back to index |
drilling: (HAAS University videos) drill bits: at least 2 diameters of flute length outside of hole "stub" and "jobber" lengths, use shortest that does the job due to rigidity top angle: 118 (general purpose HS for mild steel, Al...) or 135 deg (for harder materials) helix angle: usually 30 deg; down to 10 deg (harder to break, high-torq) for special apps - harder steels, Al alloys; up to 40 deg for difficult materias like stainless (low torque) self-center point - many cobalt, most carbide, few plain as it is harder to grind that (so they "walk" and need spot drilling) steel drills just 2-3 times their diameter carbide up to 5 times then it's peck-drill (increases edge wear as drilling is started more times) deep drills: pilot hole with stup hole to 1.5 d, then low rpm to insert to hole and then go full speed slow to 50% rpm and feed rate for last 2mm of hole as thin material won't conduct away enough heat and overheats, work hardens, wears tool unthreaded part of the bolt = "grip" should not extend more than 2 threads into the hole, otherwise thread edges act as reamers on vibrating parts
https://ruko.de/en/blog/structure-and-application-of-countersinks 60deg deburring; on some larger metric (over M20; M22 and over); some rivets 70deg some rivets 75deg rivet heads (less common? not in wikipedia article) 78deg aircraft rivets AN425 80deg (not in wikipedia) screw countersinks, DIN standard 82deg common for screws, US standard, common on Unified Thread screws 90deg common for screws, metric/ISO standard, common on metric screws; US wood screws (82deg for metal)? 100deg on aircraft/AN/milspec rivets and structural screws, AN426/427; with thin-skinned missiles and aircraft; often "reduced head" (smaller head dia) 110deg uncommon 120deg sheetmetal rivets, flat-head sunk sheetmetal screws, some small-head screws 156deg rivets for honeycomb composites 180deg flat; counterboring wafer heads: 70deg center part, 16deg topmost part; preferred for self-tapping screws bugle heads: concave shape, for drywall/plasterboard
https://books.google.cz/books?id=TYtoMguVdl0C&pg=PA46&lpg=PA46&dq=pre-war+thread+standards&source=bl&ots=3Qi6dDoapT&sig=ACfU3U2mBGCe1CW-Ow2mTT04CX9vO5YQiQ&hl=en&sa=X&ved=2ahUKEwiqs-r5mK7oAhVWi1wKHcQgDToQ6AEwE3oECAgQAQ#v=onepage&q=pre-war%20thread%20standards&f=false
M2 M2.5 (M3.5?)
1/4-36 SMA connectors, 6.35x0.706 ! 9/32"-40tpi chuck mount thread, common, Dremel chuck/collet nut thread, 7.14mm @! 5/16-32 UNEF 5.5mm power jacks, ball inflator needles, 7.94x0.794 @ 3/8-32 UNEF connectors F, TNC, BNC, bulkhead nuts; 9.53x0.794mm, close to 9v1 valve @! 3/8-24 UNF small CO2 canisters, chuck mount 3/8-20 BSF thread on fishing rod holders and fishing equipment, "M" size, misnamed as "M3/8" @!! 7/16-28 UNEF LPG gas cartridges (male on cartridge), Lindal B188 valve, usual in camping, "EN 417" (incorrectly); TNC coax connectors; 11.1x0.907 7/16-20 UNF piping on some sensors, eg. pressure for refrigeration 1/2-20 UNF drill chucks, air valves, larger CO2/N2O canisters, 12.7x1.27 1/2-13 UNC thread on stands and rods for fishing, larger size
! 5/8-27 microphone/camera stands, 15.9x0.941 5/8(-11) UNC large geodetic tripods W21.8-14 BS341, DIN477, pressure cylinders with O2, Ar, some food-grade CO2 bottles (see also G3/4, converters available) 1-32 UNS C/CS lens mount 1-14 UNF marine antenna mount
M7x0.5 e-cig 510 thread (M8x0.5) lenses
! M7(x1) standard M7, for 3d printers M8x0.75 chuck mounts, bulkhead nuts M8x1 metric pipe thread ! M10x1 welding gas cartridges, common pipe thread ! M18x1.5 spark plugs, lambda sensors
M20x1.25 stage equipment bottom stand ! M20x1.5 cable glands, oil sights, oil filters, common pressure sensors M20(x2.5) stage equipment bottom stand
!1/4-20 UNC - tripod thread small, consumer cameras, male on tripod !3/8-16 UNC - tripod thread large, bigger profesional cameras, European standard microphone holder thread, male on tripod 7/8-?? ...see "tribrach" attachment plates [ ref], [ ref]
Royal Photographic Society old suggestion: 3/16-24 BSW (3/16 inch nominal diameter, 24 threads per inch), or 1/4-20 BSW[4] for smaller cameras and 3/8-16 BSW for larger cameras and pan/tilt heads UNC threads are a 60-degree angle and flattened, whereas the BSW are a 55-degree angle and rounded crest.
!5/8-11 UNC - geodetic survey equipment, large geodetic-class tripods, drawbolt, male on the tripod???, geodetic rods ...some have three grooves for alignment pins 3.1/2-8 US Special (now generally obsolescent) - survey instruments, unused now
3/8-16 1/2-14 NPT (pipe thread) 5/8-27 - US standard microphone holder thread (15.9mm dia, 1.06mm pitch) M20x2.5 - standard thread for subwoofer mount poles, tripod stand bases (JBL EON, PRX, STX, VRX and SRX818) M20x1.25 - standard for microphone rods (and some base plates?) 7/8-27 - microphone holders, stage stands M10 M8 25mm bolt diameter? M17x1 - Neutrik gear, microphone attachment connectors - Neutrik's very popular X Series and D Series connectors, both widely recognized as industry standard most common portable stands: telescopic rod diameters: inner: 5/8", outer: 7/8" threadless sockets: 1.3/8" diameter rods into matching holes (34.925mm) 1.1/2" diameter rods (38.1mm) 1" diameter rods (25.4mm) usually 3" insert depth wobbly
M17x1 "M17" circular connectors, signal, common with microphones, Neutrix; M18x0.75 and M20x1.5 as back mounting threads M23x1 "M23" circular connectors, common with electrical drives and servo-motors in industrial automation applications; M25x1 as common shell M40x1.5 "M40" circular connectors M58x2 "M58" circular connectors cable glands M16x1.5 M20x1.5 M25x1.5 M32x1.5 M40x1.5 M50x1.5 M63x1.5 M22x2 Hirschmann "CA" connectors
[ ref]
1"-14 UNF - "standard marine", marine antenna mounts, male on tripod/mount, male or female antenna
3/8-24 UNF - antenna mounts, female on tripod, male on antenna, VHF or CB, also mini-UHF connector thread
M16 - marine antenna mounts? male on mount?
1.1/4"-11 pipe - male on stand, male on antennas? - for bigger antennas
SO-239 coax connectors - can double as antenna attachments
G3/4-14 - on a GPS antenna, Garmin standard - G3/4x14 - 14 TPI, 26.4mm outer, 24.5 inner
N240F - 1.1/4-11 mounting nut
1/4-36 UNF - SMA connectors
3/8-32 UNEF - F connectors
7/16-28 UNEF - TNC connectors
5/8-24 NEF - SO-239 UHF connector
5/8-24 UNEF - Type-N connector
M29x1.5 - HN connectors, "business end" securing threads on 7/16 DIN coaxial RF connectors
M5.5x0.5 - some fiber optic and RF connectors
M8x0.75 - some fiber optic and RF connectors
threads on antennas:
10-24 - female on mount
1/4-20 - standard small tripod
5/8-24 - standard panel nuts, common
5/8-11 - "standard survey", geodetic GPS tripod antennas
M4
M5x0.8 - female on mount
M6x1 - male on mount, small whip antennas, car antennas
M7x1 - male on mount
adapters for a M6f antenna: M7f..M6m, M5m..M6m, 10-24m..M6m, 1/4-20m..M6m
1"-14 specs: SAE/NF, Major dia. 1.00" Minor dia. .9072 Pitch dia. .9536 Tap Drill 15/16" 60 degree thread form
http://merkur.kreteni.cz/90sroubky-90historie.php https://meccanoman.co.uk/catalog/information.php?info_id=1 6BA Meccano construction sets, UK, on some early electrical parts #6-32 Erector set, USA, some set screws, usually 3/16" long; standard screw size used is #8-32 #7-32 Meccano construction sets, USA (after 1916-1922); usually 1/4" (6mm) long slotted cheesehead; for UK and pre-1922 see 5/32 BSW #8-32 Erector set, USA; usually 1/4" long slotted head; also some 6-32 set screws 5/32 BSW Meccano construction sets, USA (to 1916-22, then #7-32) and UK; usually 1/4" (6mm) long slotted cheesehead; 5/32 bolt won't fit #7 nut; other systems use M4 (Marklin), M3.5 (Merkur) M3.5 Merkur construction sets (Czech); usually 6mm long slotted cheesehead; other systems use 5/32 BSW (Meccano), #7-32 (US Meccano), M4 (Marklin) 1/8 BSW set screws in vintage Merkur construction sets (Czech, pre-WW2) Meccano hole spacing: 1/2" (some parts 1/4"); 1/2" wide strips, narrow strips ~11/32" wide Meccano axle diameter: 8SWG, 4.1mm; larger axles 5/16", 7.94mm Meccano gear module: 38dp (38 teeth on 1" diameter, measured at pitch) also 30DP (special from Tony Bolton), 20DP ("Large Tooth Parts") from Meccano compatibles, 16DP (trad. Geared Roller Bearings, Large tooth Quadrants, some recent Junior Meccano plastic parts) Meccano gear bosses: 3/8" dia (some 1/2" dia) Merkur hole spacing: 10mm Merkur gears: 0.5mm module (0.6mm by one source), some 1mm module (some worm gears) Merkur set screws: M3, M4, 1/8 BSW (old) Erector sets:
http://www.mettex.co.uk/wp-content/uploads/2014/11/Fabory-Fasteners-Technical-Information.pdf ISO 1478, EN 21478, DIN 7970 ST2.2(x0.8) ISO #2 ST2.6(x0.9) ISO #3 ST2.9(x1.1) ISO #4 ST3.3(x1.3) ISO #5 ST3.5(x1.3) ISO #6 ST3.9(x1.3) ISO #7 ST4.2(x1.4) ISO #8 ST4.8(x1.6) ISO #10 ST5.5(x1.8) ISO #12 ST6.3(x1.8) ISO #14
http://www.mettex.co.uk/wp-content/uploads/2014/11/Fabory-Fasteners-Technical-Information.pdf DIN 906 M8x1 M10x1 M12x1.5 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M24x1.5 M30x1.5 M36x1.5 M42x1.5
Size1) Length (in) Gauge Nominal Shank Diameter (in) Nominal Shank Length (in) Number of Nails in a pound 2d 1 15 0.072 1 876 3d 1¼ 14 0.083 1.25 568 4d 1½ 12½ 0.109 1.5 316 5d 1¾ 12½ 0.109 1.75 271 6d 2 11½ 0.12 2 181 8d 2½ 10¼ 0.134 2.5 106 10d 3 9 0.148 3 69 12d 3¼ 9 0.148 3.25 64 16d 3½ 8 0.165 3.5 49 20d 4 6 0.203 4 31 30d 4½ 5 0.22 4.5 24 40d 5 4 0.238 5 18 60d 6 2 0.238 6 11
http://kanco.ir/wp-content/uploads/2015/08/AWWA-C-800-2013.pdf size copper rdbrass steel corpstop speccoup flarcopp inlet intaper 1/8 0.405 1/4 0.375 0.540 3/8 0.500 0.675 1/2 0.625 0.840 0.840 0.604-12 31/32-14 1.004-14 0.819-14 1.75 7:48 5/8 0.750 0.735-12 1.3/32-14 1.160-14 1.016-14 1.75 7:48 3/4 0.875 1.050 1.050 0.855-12 1.1/4-14 1.259-14 1.104-14 1.75 7:48 1 1.125 1.315 1.315 1.089-12 1.1/2-12 1.593-11.5 1.332-12 1.75 7:48 1.1/4 1.375 1.660 1.660 1.374-10 2.055-11.5 1.728-11.5 1 1:12 1.1/2 1.625 1.900 1.900 1.666-8 2.465-11.5 2.004-11.5 1 1:12 2 2.125 2.375 2.375 2.165-8 3.185-11.5 2.577-11.5 1 1:12 corpstop - internal driving thread for corporation stops speccoup - special purpose coupling threads for corporation stops flarcopp - fitting thread for flared copper service tube inlet - standard AWWA corporation stop inlet thread, diameter at small end, tapered intaper - inlet thread taper, inches per foot, across diameter plug-type corporations (corporation valves) are for 100 psi in 1/2", 3/4" and 1" size, 80 psi in 1.1/4..2" AWWA aka CC thread is similar to NPT, with steeper taper
interchangeability: 1/8 #5 5/32 #8 3/16 #10 7/32 #12 1/4 1/4 5/16 5/16 3/8 3/8
% pitch dias 1 1 3 1 1.25 ? 6 2 1.3/4, 2 3 2.5 1.1/2 5 3 1.1/4, 2.1/4 38 4 3/4, 7/8, 1, 1.1/8, 1.1/4, 1.3/8, 1.1/2, 1.3/4, 2, 2.1/4 10 5 3/4, 1, 1.1/4 7 6 5/8, 7/8, 1.1/8 1 6.5 ? 17 8 1/2, 5/8, 3/4 1 9 ? 8 10 1, 1.1/4, 1.1/2, 1.3/4 2 12 ? plumbers' fine threads: fine threads on thin brass tubes, many standards, to be unified condenser tube ferrules: differing standards valve stem threads: mostly truncated 60deg modified ACME instrument screws: many vendor-specific standards, some use of NF instrument tubes: French standard for threaded brass tubes for optical instruments set in Dec 1916
HM1 HM1-32 HM1.5 HM2 HM3 HM4 HM10 HM18 HM20 HM30 HM125
K1 line: internal: M1.5 external: conical, 2-start, 1.8mm (0.9mm) pitch; narrow core internal: M1.8 external: conical, 2-start, 1.8mm (0.9mm) pitch; regular and wide core mount screws inside the implant: M1.5 M1.8 M2 http://dentalstudio.co.kr/en/abutment-alignment-pin/?cat=115/ http://www.neoimpladr.com/fixture-screw-remover/fixture-remover-screw M1.4 M1.54 rare, NobelActive M1.6 most standard size M1.8 1-72 UNF M2 most standard size M2.5 https://www.lasak.cz/wp-content/uploads/2019/01/2019_BioniQ_katalog_CZ_bez_cen_web.pdf implant external threads, BioniQ S2.9 S3.5 S4.0, T4.0 S5.0, T5.0 M1.6, M2 - common for attachment spheres
https://www.celofixings.es/import/catalogue_celo_industry.pdf 2x1 2.5x1.15 3x1.35 3.5x1.55 4x1.75 4.5x2 5x2.25 6x2.65 7x3.1 8x3.5 Remform II threadforming screws, for plastic; 30deg asymmetric 1.8x0.8 rest as Remform II Remform F with finer pitch Plastite 48-2 2.2x0.9 2.5x1.06 2.9x1.27 3.5x1.34 3.9x1.41 4.2x1.59 4.5x1.7 4.8x1.81 5.5x2.3 2.2x0.9 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 2.5x1.06 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 2.9x1.27 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 3.5x1.34 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 3.9x1.41 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 4.2x1.59 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 4.5x1.7 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 4.8x1.81 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread 5.5x2.3 thread-forming screws, Plastite 48-2, for plastic; 48deg twin thread Plastite 45 2.5x1.4 3x1.5 3.5x1.65 4x1.75 4.5x2 5x2.2 6x2.5 2.5x1.4 thread-forming screws, Plastite 45, for plastic; 45deg thread 3x1.5 thread-forming screws, Plastite 45, for plastic; 45deg thread 3.5x1.65 thread-forming screws, Plastite 45, for plastic; 45deg thread 4x1.75 thread-forming screws, Plastite 45, for plastic; 45deg thread 4.5x2 thread-forming screws, Plastite 45, for plastic; 45deg thread 5x2.2 thread-forming screws, Plastite 45, for plastic; 45deg thread 6x2.5 thread-forming screws, Plastite 45, for plastic; 45deg thread PCB screw, for plastic self-tapping screws, IBI-ZAS; asymmetric 40deg thread 3x0.8 3.5x0.95 4x1.05 5x1.25 6x1.4 Pushtite II, thread-forming screws, push-in screw-out, for plastic; asymmetric 10+70 deg thread 2x1.05 2.5x1.15 3x1.2 3.5x1.35 4x1.55 4.5x1.7 5x1.8 6x2.1 Uni-Alloy, self-tapping, for aluminium and zinc alloys https://www.unisteeltech.com/self-tapping-screws/uni-alloy.html 0.8x0.2 1x0.2 1.2x0.25 1.4x0.3 1.6x0.35 1.8x0.4 2x0.45 2.2x0.5 2.5x0.6 2.6x0.6 3x0.7 Uni-Mag, self-tapping, for magnesium alloys https://www.unisteeltech.com/self-tapping-screws/uni-mag.html 0.8x0.35 1x0.4 1.2x0.45 1.4x0.5 1.6x0.55 1.8x0.6 2x0.65 2.2x0.7 2.5x0.8 3x1 Delta PT, self-tapping, for plastics, wide range of thermoplastic materials https://www.unisteeltech.com/self-tapping-screws/delta-pt.html 1x0.44 1.2x0.51 1.4x0.57 1.6x0.64 1.8x0.71 Remform II https://www.unisteeltech.com/self-tapping-screws/remform-f.html 2.5x1.15 Remform II threadforming screws, for plastic; 30deg asymmetric, round thread tip 1x0.55 1.2x0.65 1.4x0.75 1.6x0.85 1.8x0.85 2x1 Taptite 2000, for metals, trilobular, matches standard metric thread https://www.unisteeltech.com/self-tapping-screws/taptite-2000.html M1x0.25 1.2x0.25 1.4x0.30 1.6x0.35 1.8x0.35 2x0.4
https://www.portlandbolt.com/technical/thread-pitch-chart/ https://www.gewinde-normen.de/en/8-un-thread.html 8UN thread is commonly used for petrochemical fasteners like stud bolts. 1-8 1.1/16-8 1.1/8-8 1.3/16-8 1.1/4-8 1.5/16-8 1.3/8-8 1.7/16-8 1.1/2-8 1.9/16-8 1.5/8-8 1.11/16-8 1.3/4-8 1.13/16-8 1.7/8-8 1.15/16-8 2-8 2.1/8-8 2.1/4-8 2.3/8-8 2.1/2-8 2.5/8-8 2.3/4-8 2.7/8-8 3-8 3.1/8-8 3.1/4-8 3.3/8-8 3.1/2-8 3.5/8-8 3.3/4-8 3.7/8-8 4-8 4.1/8-8 4.1/4-8 4.3/8-8 4.1/2-8 4.5/8-8 4.3/4-8 4.7/8-8 5-8 5.1/8-8 5.1/4-8 5.3/8-8 5.1/2-8 5.5/8-8 5.3/4-8 5.7/8-8 6-8 1-8 8UN 8-thread series,
most common: 8UN 12UN 16UN less common: 4UN 2.5..6" 6UN 1.?..6" 20UN 28UN 32UN 1/2..1" 4UN: 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 6UN: 1.3/8 1.7/16 1.1/2 1.9/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 12UN: 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 16UN: 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 3.1/8 3.1/4 3.3/8 3.1/2 3.5/8 3.3/4 3.7/8 4 4.1/8 4.1/4 4.3/8 4.1/2 4.5/8 4.3/4 4.7/8 5 5.1/8 5.1/4 5.3/8 5.1/2 5.5/8 5.3/4 5.7/8 6 20UN: 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 1.9/16 1.3/4 1.13/16 1.7/8 1.15/16 2 2.1/8 2.1/4 2.3/8 2.1/2 2.5/8 2.3/4 2.7/8 3 28UN: 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4 1.5/16 1.3/8 1.7/16 1.1/2 32UN: 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1
https://www.verkon.cz/technicke-sklenene-teplomery/ M20x1.5 usual housings for liquid-filled thermometers, https://www.verkon.cz/technicke-sklenene-teplomery/
3/8-20 BSF (also confusingly "M3/8" - for M=mid, also S and L?) - do not confuse with UNC, UNC is 60deg, BSF is 55deg 1/2-13 UNC
[ ref]
BSF nut, BSF bolt: no play, match
BSF nut, UNC bolt: overly tight fit, needs force, can seize
UNC nut, BSF bolt: some small play, can wiggle out over time
UNC nut, UNC bolt: no play, match
8-32 archery arrow tips; male on tip, industry standard (all inserts except Easton Deep Six) 1/4-20 5/16-24 ...1/4-20 to 5/16-24 - Doinker Adapter Screw
8-32 archery, arrow tips; male on tip/arrowhead, industry standard (all inserts except Easton Deep Six) 10-24 archery, typical mounting holes for sights on bows 1/4-20 archery, some stabilizers on bows; adapter to more common 5/16-24 exists 5/16-24 archery, typical stabilizer and arrow rest mounting holes on bows; adapters to 1/4-20 exist diameters of arrow field points (not threads): 11/32 (8.73mm), 21/64 (8.33mm), 5/16 (7.94mm), 9/32 (7.14mm) masses: 100, 125, 145, 150, 175 grains (6.48g, 8.01g, 9.40g, 9.72g, 11.34g) diameters of arrow shafts: wood, 11/32 and 5/16 crossbow arrows: usual length 20", can be 16..26, usual 18 and 20
1/4-28 billiard/pool cue joining pin (also 5/16-14, 3/8-11, 3/8-10), unusual 5/16-18 billiard/pool cue joining pin (also 5/16-14, 3/8-11, 3/8-10), common 5/16-14 billiard/pool cue joining pin (also 5/16-18, 3/8-11, 3/8-10); some inserts with 7/16-20 thread 3/8-16 on billiard/pool cues 3/8-11.5 on some billiard/pool cue joining pins, nonstandard? 3/8-11 billiard/pool cue joining pin, also 5/16-14, 5/16-18, 3/8-10; uncommon? 3/8-10 billiard/pool cue joining pin; also 5/16-14, 5/16-18; standard 7/16-11 billiard/pool cue joining pin, less common 3/4-16 billiard/pool cue joining pin, less common 3/8-11.5
muzzle end threads: [ ref] [ ref] 11/32-48 barrel end thread, Smith and Wesson 422, 622 and 2206 3/8-24 barrel end thread, Kel-Tec PMR-30 (.22 cal) 1/2-36 barrel end thread, common at 9mm cal; Troy M5 PCC carbine, AR-15 (9mm), M-16 (9mm), AR-180 (9mm) Colt AR 9mm, some Diamondback 9mm PCC carbine, CMMG Wasp 9mm 1/2-30 Factory Heckler-Koch MP5-N (9mm) !1/2-28 UNEF barrel end thread, most common at 9mm cal, .223 (5.56 NATO), .22 LR, .22 MAG, .17 HMR, 5.56 == .223; standard AR-15 (.223), M16 (.223), AR-180 (.223), older CZ EVO Scorpio (9mm), Ruger 10/22 Tactical (.22), newer Mini 14 (.223), MPA57 (5.7x28), MPA Mini (9mm) 1/2-20 barrel end thread, Tec 22 (.22), CZ-452/455 (.22/17 HMR) 1/2-18 barrel end thread, rarely seen 9/16-36 some 9mm glocks, rare 9/16-32 some 9mm Glocks, for compensators !9/16-24 barrel end thread, most common at .40 cal; Ruger Mini (5.56), AR Grendal (6.50), older Mini 14 (.223), L1-a1 (.308), Glock 20 (10mm), HK94 (9x19mm), MP5 (9mm) 9/16-24 left barrel end thread, FN FAL (.308) .578-28 barrel end thread, most common at .45 cal, threaded 1911 (.45) !5/8-24 barrel end thread, most common at .30 cal (US, see also M18x1 for Eur), .308/7.62mm and .338LM (Lapua Magnum), many .30; standard AR-10 (.308), M-14 (.308), AR-15 (7.62x39), UZI Carbine/SMG (9mm), Ruger Mini 30 (.30), CMMG chrome-lined 9mm barrels, Nemo Omen (.300 Win Mag), FN SCAR 17 (.308), 300 Blackout (.300) 5/8-11 barrel end thread, M11/M12 (.380) 11/16-24 barrel end thread, alternative at .308 cal, alternative at bull barrel, .450 Bushmaster mb450 11/16-16 barrel end thread, MPA .45 cal rifles 3/4-24 barrel end thread, Desert Tactical Arms (.338LM), Barrett MRAD (.338LM), .450 Bushmaster 3/4-10 barrel end thread, M10/M11 (9mm) 7/8-14 barrel end thread, common at .50 BMG; Barrett, EDM 7/8-9 barrel end thread, MPA10 (.45) 1"-14 barrel end thread, common at .50 BMG; McMillian TAC-50 (.50), Armalite AR50 (.50), AR450 (.50) 7/16-32 7/16-28 1/2-32 9/16-28 5/8-32 barrel end thread, .450 Bushmaster 11/16-32 3/4-32 3/4-28 1-32 1/2-28 UNEF firearms, common .22LR gun/pistol silencers, US standard (also 1/2-20). Ruger SR22 1/2-20 UNF firearms, common .22LR gun/pistol silencers, European standard (also 1/2-28) 9/16-28 .40S&;W or .45ACP, .30 rifles (uncommon) 5/8-28 5/8-18 5/8-32 458 socom, 450 bushmaster, etc M8x0.75 barrel end thread, Walter P22 (.22), M-P 22 (.22), Colt/Umarex 1911 A1 (.22), Colt Gold Trophy (.22) M9x0.75 barrel end thread, on .22 LR Sig Mosquito, Glock 44-1/2, SIG 1911-22, first generation ISSC M22 M10x0.6 barrel end thread, female on barrel, on Walther PP Sport, Manurhin PP Sport pistols M10x1 barrel end thread, male on barrel, on .22 LR ISSC M22 Gen 2 threaded pistol, Artemis CP2 M10x1 barrel end thread, female on barrel M11x1 barrel end thread, female on barrel, on WE pistols M11.5x1 barrel end thread, female on barrel, on MP7A1 HK M12x1 barrel end thread, female on barrel M12x1 barrel end thread, male on barrel, Sig P226 Air pistol M13x0.75 barrel end thread, male on barrel, on Browning Hells Canyon Speed in .30-06 M13x1 barrel end thread, Galil (.223, .308), older Glock 26 (9x19mm) M13x1 left barrel end thread, Steyr Aug (5.56) M13x1.25 barrel end thread, male on barrel, on Browning X-bolt Hells Canyon Speed M13.5x1 left barrel end thread, Heckler-Koch 9mm, Sig Sauer P228/P229/P239 (9mm) M14x1 barrel end thread, male on barrel, most Oberland Arms AR15 (?), VZ58 (7.62x39), AK-47 (7.62x39), Yugo SKS (7.62x39), "AK-type commie firearms" M14x1 left barrel end thread, male on barrel, AK-47 (.308), common accessories M14.5x1 left barrel end thread, Heckler-Koch .40 M15x0.75 barrel end thread, on metric M14 (Norinco M305) M15x0.75 left barrel end thread, on Saiga 410 shotgun M15x1 barrel end thread, Heckler-Koch 93/33/G-53 (5.56), Heckler-Koch 91/G3 (7.62x39) M16x1 barrel end thread, Heckler-Koch Mark 23 (Socom) (.45) M16x1 left barrel end thread, threaded Heckler-Koch .45 barrel; Heckler-Koch USP Tactical (.45), Heckler-Koch Mark 23 (.45); Kriss Vector, "euro stuff" M17x1 barrel end thread, MAS 1949-56 (.308) M18x1 barrel end thread, Sako TRG (.308, .338LM), newer CZ EVO Scorpio (9mm); most common for .30 cal in Europe (see also 5/8-24) M18x1.5 barrel end thread, Accuracy International (.308, .338LM) M22x0.75 barrel end thread, Saiga 12ga shotgun M24x1.5 barrel end thread, AK-74 (7.62x39, 7.62x54, 5.45x39, 5.56x45) M26x1.5 left barrel end thread, PAP M92/M85 (7.62x39/.223 Remington), Zastava Yugo M92 and M85 ("Krinkov") M28x1.5 barrel end thread, female on barrel, on Diana 56 Target Hunter air rifle oil filters: 3/4-16 UNF vehicle oil filter thread, popular for improvised silencers; Ford, Dodge, Jeep, non-diesel Toyota/Lancia/Nissan, most Volvo, Suzuki... 13/16-16 UNF vehicle oil filter thread, popular for improvised silencers; Chevy, GM 3/4-14 NPT standard pipe fitting, popular for improvised silencers; Napa 4003 fuel filter, Wix 24003 fuel filter ...all three can be on one adapter
other dimensions: M22x1.5 vehicle oil filter thread M20x1.5 vehicle oil filter thread; some Ford, HOnda, Hyundai, Lada Niva Diesel, Mazda, Mitsubishi, some Peugeot, Subaru, some Volvo... M18x1.5 vehicle oil filter thread 1/2" BSP vehicle oil filter thread M16x1.5 vehicle oil filter thread 1.3/16-16 firearm barrel buffer tube thread, AR lower thread adapters: 1/2-28 to: 13/16-16, 3/4-NPT, 1"-14, gunsmithing taps: 1/2-20 ---- $24.99 1/2-32 ---- $23.99 1/2-36 ---- $19.99 3/4-16 ---- $26.99 M15x1.0RH ---- $24.99 M14x1.0RH ---- $19.99 3/4-20 ---- $25.99 M9x0.75R ---- $29.99 11/16-24 ---- $36.99 m16x1.0LH ---- $29.99 m18X1.0RH ---- $39.99 m18x1.5RH ---- $26.99 m12x1.25RH ---- $14.99 m13.5x1.0LH ---- $58.99 9/16-24 ---- $26.99 MagLite threads (bodies popular for silencers) 5/8-27 MagAA 1 1/8-20 MagC - NOT!! 1 1/2-20 MagD - PROBABLY NOT! Barrel & Receiver Threads; https://www.brownells.co.uk/RECEIVER-TAPS-Rem-700-Tap-BROWNELLS-Remington-High-Speed-Steel-Plug-080598116 .980"-12 tpi fits Small Ring Mauser (plug tap cuts full-depth threads on small ring 98s with internal shoulders) 1.00"-16 tpi fits FN-FAL; 1.10"-12 tpi fits Large Ring Mauser 11⁄16"-16 tpi fits Remington 700 and XP-100 1.055"-20 tpi fits Savage 110/112. two most important threads on the AR-15/M16 receivers: 1.250"-18 tpi - Corrects out of spec or cross-threaded upper receivers and barrel nuts. 1-3/16"-16 tpi - Makes receiver extension (recoil buffer) tube and lower receiver threads uniform for easier installation. Semi-auto pistol custom compensators for reduced recoil and better control: Unthreaded comps should be drilled with 3-5/64" HSS drill then reamed to .551" before threading with either tap. Turn barrels to approximately .002" smaller than thread diameter. .575"-40 thread matches most commercial, tapered-sleeve or integral, cone-style comps. .581"-40 thread is same as used on Wilson, Brown and Storm Lake Machine barrels and bushing style comps. .685"-40 thread is used to fit compensators to threaded Bull and Hybrid barrels. Popular revolvers: https://www.brownells.co.uk/REVOLVER-BARREL/FRAME-TAPS-N-Frame-Tap-BROWNELLS-Smith-Wesson-High-Speed-Steel-Plug-080598670 Colt Single Action, .695"-20 thread, 1-½" dia. die J Frame, .500"-36 threads. 1" dia. die K Frame, .540"-36 threads. 1" dia. die L Frame, .562"-36 thread, 1-½" dia. die N Frame, .670"-36 thread, 1-½" dia. die Ruger® Single Action (centerfire), .680" - 24 thread, 1-½" dia. die GP-100®, .625"-24 thread, 1-½" dia. die Redhawk® (all models): .750 "-20, 1-½" dia. die 0.500-36 (M12.7x0.706) firearm revolver barrel/frame thread; J Frame 0.540-36 (M13.72x0.706) firearm revolver barrel/frame thread; K Frame 0.562-36 (M14.27x0.706) firearm revolver barrel/frame thread; L Frame 0.575-40 (M14.605x0.635) firearm semiauto pistol recoil compensator thread; most commercial, tapered-sleeve or integral, cone-style comps 0.581-40 (M14.757x0.635) firearm semiauto pistol recoil compensator thread; used on Wilson, Brown and Storm Lake Machine barrels and bushing style comps 0.625-24 (M15.875x1.06, 5/8-24) firearm revolver barrel/frame thread; GP-100 0.670-36 (M17.02x0.706) firearm revolver barrel/frame thread; N Frame 0.680-24 (M17.27x1.06) firearm revolver barrel/frame thread; Ruger Single Action (centerfire) 0.685-40 (M17.399x0.635) firearm semiauto pistol recoil compensator thread; used to fit compensators to threaded Bull and Hybrid barrels 11⁄16-16 (M17.46x1.59) firearm rifle barrel/receiver thread; fits Remington 700 and XP-100 0.695-20 (M17.65x1.27) firearm revolver barrel/frame thread; Colt Single Action 0.750-20 (M19.05x1.27, 3/4-20) firearm revolver barrel/frame thread; Redhawk (all models) 0.980-12 (M24.89x2.12) firearm rifle barrel/receiver thread; fits Small Ring Mauser (plug tap cuts full-depth threads on small ring 98s with internal shoulders) 1.00-16 (M25.4x1.59) firearm rifle barrel/receiver thread; fits FN-FAL; 1.10"-12 tpi fits Large Ring Mauser 1.055-20 (M26.80x1.27) firearm rifle barrel/receiver thread; fits Savage 110/112. 1.3/16-16 (M30.16x1.59) firearm rifle barrel/receiver thread; AR15/M16 receiver extension (recoil buffer) tube and lower receiver threads 1.1/4-18 (M31.75x1.41) firearm rifle barrel/receiver thread; AR15/M16 upper receivers and barrel nuts suppressor adapters https://trosusa.com/suppressor-thread-adapters/ muzzle brakes: https://harrellsprec.com/sc_images/muzzle-brake-chart-4-10.png Maglite: http://www.candlepowerforums.com/vb/showthread.php?39990-Mag-tailcap-thread-pitch-and-diameter 5/8-27 Maglite flashlight tubes, AA-size, internal (tailcap) 1.3/16-24 Maglite flashlight tubes, B-size, internal (tailcap) 1.????-20 Maglite flashlight tubes, C-size, internal (tailcap) (possibly M28x1.5?) 1.1/8-20 too big, 1.1/16-20 too small 1.7/16-20 Maglite flashlight tubes, D-size, internal (tailcap) full-C and ML sizes have different threads 1.3/8-24 firearms, many QD-mount end caps, Phantom QD silencer system 1.11/16-20 SDTA Option A tubes, 1.75" tubes 1.180-24 firearm silencer mounts, male on mount, eg. MMW Reflex, SDTA
3/8 WW1 US MkI grenade (8x4 segments) filling hole 9/16-12 14.3mm, WW2 US MkII "Pineapple" grenade (8x5 segments), fuze and filling hole; WW1 MkI grenade (8x4 segments) fuze SpM15.45-13 AF-11 (FD-1), AF-12 (FD-1P), AF-13 (FD-2) fuze for offensive/defensive hand grenades, AF-17 for smoke grenades M20x2 AF-14 (FID-1) fuze for smoke, flashbang hand grenades M217 fuze, M26A2 grenade, M57, M59, M33A1, M68 grenade, 5/8-11 M204A1, M204A2 fuze, M215 fuze, M26, M26A1, M61, MK2 ("pineapple") grenade 5/8-11 M213 fuze, M33, M67 frag grenade (2.5" sphere); M228 fuze, M69 practice grenade 9/16-12 UNC-1A M201A1 fuze, AN-M8 smoke grenade, M18 smoke grenade, AN-M14 incendiary grenade, M7, M7A1 CN-gas riot grenade, M7A3 CS-gas grenade, M58 CS-gas grenade, M83 practice smoke M206A1, M206A2 fuze, M15 WP smoke grenade, M34 WP smoke grenade, MK3A2 offensive grenade M227 fuze, M48 nonlethal training smoke grenade, training aid for M47 grenade; M47 CS-gas riot grenade 9/16-12 M205A1,M205A2 fuze, M30 training grenade (equiv. M26,M26A1), M62 9/16-12 UNC US standard grenade fuze well thread M10x1 German WW2 grenade M39, fuze BZE 39 "The fuze is what gives it away as a novelty grenade. The fuze on your grenade is either an M213 or an M228 fuze (the crooked spoon and the notch for the "jungle clip" tell us this.) A real MKII uses an M10 series fuze (i.e., M10, M10A1, M10A2, M10A3) or an M6 series fuze. The M21 (a practice grenade version of the MKII) practice grenade uses the M205 practice fuze. You can also verify this (i.e, your grenade being a novlety vs a real one) if you have access to either a MKII or an M21. The threads on the M10 series, M6 series, and M205 practice fuzes are the same and they are a different thread pitch than the M213 and M228 fuzes and they will not interchange. The M10/M6 fuzes will not fit the repro/novelty grenades." illum.grenade: 25-sec burn, 55000 candlepower, 200m-diameter area illuminated, 3.5oz light composition cinnamic acid: training simulant for CS gas (L97A1 grenade) http://bulletpicker.com/pdf/TM%2043-0001-29,%20Grenades.pdf#page=72
https://www.krusik.rs/en/wp-content/uploads/2016/10/UPALJACI_eng.pdf M33x2 UTI-M84 fuze for 128mm cal. missiles M63, M87, Plamen-D SpW36.18-10 Br-1 57mm honeycomb-launcher rocket warhead fuze UTI-1, UTI-2; 128mm rocket "Munja" warhead fuze; UTIU-M72B1 fuze for cal.85,100,122,130,152 HE grenades; UTIU-M85 fuze for cal.100,115,125 grenades sp36.18-10 AF-61, M6 mortar fuze; AF-67 mortar fuze M36.18-10 UTI-M84P1 fuze for 107mm cal. M15 rocket M38x2 UT-M68P1 mortar shell fuze 1.5-12 UNF-1A 38.1x2.12, ETU, M365, for 60, 81/82, 120mm mortar shells; UT-M88P1; PD UTU M93-N; AF-66 for HE80, HE84LD, HE70LD, FRAG-82LD; AF-62 (M6-N), AF-64 (M52-B3) M43x2 UT-M88P2 mortar shell fuze; PD-UTU M93P1 SpM44.96x2 MRV-U M85 fuze for 122mm "Grad" rocket warhead M45x2Sd9 UTU-M78 mortar shell fuze 2"-12 NS UTIU-M15 fuze for 155mm M107 HE howitzer projectile M52x2 UTU-M77 128mm "Oganj" HE warhead M52x3 AUFK-M91 fuze for aircraft bombs M54x1.5 TP-M67P1, for 60mm cal. mortar shells M72x1.5 TP-M67P1, for 81/82mm cal. mortar shells M97x2 TP-M87, for 120mm mortar shells fuze safeties: mortar shell: 12000g, drop safety 3m; moisture proof typ. 0.5..1 bar; delays 30..50 msec mortar shell: 400..13000g (electronic) mortar shell: inertial, MIL-STD-1316B, 400..13000g mortar 122mm: 700g "Oganj" missile: 200g Br-1 57mm misile: inertia, 10-15s self-destruct time "Munja" rocket: 150g M63/M87/Plamen-D missile: 8000..14000 rpm, MIL-STD-316B, drop-safety 3m 107mm M15 rocket: over 12000 rpm, drop-safe 3m 85,100,122,130,152mm grenades: 3000g, 4000 rpm, drop-safe 1.75m 100,115,125mm grenades: 3000g, drop-safe 1.75m 155mm M107 projectile: 3000g, 3100 rpm, drop-safe 3m, delay 0 or 20..50 msec "Grad" missile: 20g, drop-safe 3m, safed during active motor burn; delay 0 or 1..5 msec or 7..13 msec
M6x1 old Russian
M9x1 newer Russian
M9.5x1 MEC, Gehmann, Anschütz, Centr... [ ref]
3/8-24 UNF
M18x0.5 "M18", fits ANSCHUTZ, Diana, Walther and Feinwerbau 601 or other M18 frontsights, Gehmann adjustable aperture front sight
M18x0.75
M19x0.75
M22x0.5 "M22"
M8x1 M9x1 M10x1 M10x1.25
M8x1 M10x1 M12x1.25 M19x1.25
http://www.eurodiesel.com/files/Nozzle_Cap_Nuts.pdf M15x0.5 Omap, Bosch, Lucas, Siemens M15x0.75 Omap, KHD M15.3x0.5 Delphi M16x0.75 Bosch, Caterpillar M16x1 Denso M16x1.5 Bosch M17x0.5 Denso, Toyota, Mitsubishi, Nissan, Subaru, Mazda M17x0.75 Mercedes common rail, Bosch M19x0.75 Omap, Lombardini, Stanadyne, Bosch, Iveco, KHD, Lucas, Isuzu M19x1 Zexel M19x1.25 Cav, Iveco, Omap, Fiat, Lucas M19x1.5 Fiat, Bosch, Isuzu M20x1.25 M20x1.5 VM, Omap, Bosch, Denso M22x1.5 Omap, Lombardini, Bosch, Kubota, Toyota, Perkins, Diesel Kiki, Denso M23x1 Bosch M24x1 Bosch M24x1.5 Omap, Deutz M24x2 Omap, Bosch, Kubota, Diesel Kiki, Denso M25x0.75 Bosch M28x1 Delphi 0.605-40 UNS Stanadyne, Perkin, Lister Petter, Isotta Fraschini, Ambac 3/4-16 UNF Omap, Stanadyne, Ambac, Mac, Perkin, Caterpillar, Deutz Mack, Zexel, Bosch
M11x1.5 gas diffuser nozzle M9x1.25 1/4-28 wire guide insert M6 wire guide insert
M3x0.3 M4x0.4 M5x0.5 M6x0.6 M8x0.7 M10x0.9
air gun nozzles: 1/8 NPSM (male NPS) 1/8 MNPT (male NPT) NPT: tapered NPS: straight 1/2-27 UNS air blow guns, air nozzles, female on handpiece, male on nozzle, TYPHOON guns M12x1.25 air blow guns, air nozzles, female on handpiece, male on nozzle nozzles: M4x0.5 female or male on nozzle M5x0.5 male on nozzle M6x0.75 male on nozzle 1/8 BSPF 1/4 BSPF 3/4 BSPM 1 BSPM 1 BSPF 1-1/4 BSPF 1-1/4 BSPM 1/2-27 gas burner orifice thread 3/8-27 gas burner orifice thread https://www.practicalmachinist.com/vb/general/how-cut-27-tpi-threads-lathe-343738/ 27 pitch is used almost exclusively for small tapered pipe threads, some mike stands, and the straight brass pipe thread used in lighting fixtures. If the engagement is short and the thread is a set used like in a light fixture where mechanical strength is of little consequence you can use 28 threads per inch and bore or thread for clearance. It won;t fit right but it will do the job.
inflator needles: ~38mm long, 1.88mm outer dia thread: 5/16-32 UNEF basketball needle: outer 0.27", inner 0.16" also: 1/8" NPT bicycle valve standards: "Presta", "Schrader" air valve threads: 1/8-27 NPT air M10x1 air, fuel 1/2-20 UNF-3A high pressure, shock absorber valve 5/16-32 UNEF-2A air, fuel 5/16-18 UNC-2A fuel 1/8-28 British A/C caps: .305-32 Schrader external .482-26 7/16-20 UNF 2A tank valves: [ ref] 1/4-18 NPT 1/8-27 NPT ...
cap thread tank thread .305-32 1/8-27 NPT .305-32 1/8-27 NPT .305-32 1/4-18 NPT .305-32 M10x1 .305-32 5/16-32 UNEF 2A .482-26 1/2-20 UNF 3A 7/16-20 UNF 1/8 NPT 7/16-20 UNF 2A 1/8-28 British 7/16-20 UNF 2A 5/16-18 UNC 2A .485-26 .305-32 - most common Schrader valve caps 3/8-24 NPT for 3/16 flared tube 1/8 NPT 7/16-20 for 1/4 flared tube
https://en.wikipedia.org/wiki/Valve_stem
most car and motorbike tires, wide bicycle tires, refrigeration, HVAC, plumbing, fuel systems, SCUBA regulators, aircraft hydraulics for detaching hoses in use, for quick pressure checks different stem diameters, usually 8mm and more external thread: 0.305"-32 (7.747-0.7938mm) internal thread: 0.209"-36 (5.309-0.7056mm)
most bicycles, especially racing bikes stem outer dia 6mm thread dia 5V2 (5.2x1.058mm) - ISO 4570 outer thread of hreaded valves 6V1 (6.0x0.8mm - M6????)
bicycles, used mainly on cheaper bikes in many countries ext thread 0.305-32 (7.747-0.7938mm), same as Schrader can be inflated with Presta pumps
similar to Presta, used mainly in Italy
rim holes: 8.5mm (Schrader, Dunlop), 6.5mm (Presta)
gas cylinder valve inlet threads: 3/8-18 NGT (LPG), 1/2 NGT (small oxygen), 3/4-14 NGT (most common), 1-11.5 NGT, GB8335 PZ27.8 [ ref]
http://pages.cs.wisc.edu/~bolo/workshop/thread.html 0.15-55 Holtzapfels R, historical, 3.81x0.462 0.162-39.9 Holtzapfels Q, historical, 4.115x0.637 0.18-36.1 Holtzapfels 0, historical, 4.572x0.704 0.185-55 Holtzapfels S, historical, 4.699x0.462 0.19-39.9 Holtzapfels P, historical, 4.826x0.637 0.2-36.1 Holtzapfels N, historical, 5.08x0.704 0.21-28.9 Holtzapfels L, historical, 5.334x0.879 0.24-36.1 Holtzapfels M, historical, 6.096x0.704 0.25-25.7 Holtzapfels K, historical, 6.35x0.990 0.29-25.7 Holtzapfels J, historical, 7.36x0.990 0.33-25.7 Holtzapfels I, historical, 8.382x0.990 0.36-19.9 Holtzapfels H, historical, 9.144x1.277 0.41-19.9 Holtzapfels G, historical, 10.414x1.277 0.45-16.5 Holtzapfels F, historical, 11.43x1.539 0.5-13.1 Holtzapfels E, historical, 12.7x1.940 0.56-13.1 Holtzapfels D, historical, 14.224x1.940 0.625-13.1 Holtzapfels DD, historical, 15.875x1.940 0.75-9.5 Holtzapfels C, historical, 19.05x2.688 0.875-8.3 Holtzapfels B, historical, 22.225x3.079 1-6.6 Holtzapfels A, historical, 25.4x3.860
1x0.25 1.2x0.25 1.4x0.3 1.7x0.35 2x0.4 2.3x0.4 2.6x0.45 3x0.5 3.5x0.6 4x0.7 4.5x0.75 5x0.8 5.5x0.9 6x1 7x1.1 8x1.2 9x1.3 10x1.4 12x1.6 14x1.8 16x2 18x2.2
0.4x0.1 4 0.45x0.1 4 1/2 0.5x0.125 5 0.55x0.125 5 1/2 0.6x0.15 6 0.65x0.15 6 1/2 0.7x0.175 7 0.75x0.175 7 1/2 0.8x0.2 8 0.85x0.2 8 1/2 0.9x0.225 9 0.95x0.225 9 1/2 1x0.25 10 1.1x0.275 11 1.2x0.3 12 1.3x0.325 13 1.4x0.35 14 1.5x0.375 15 1.6x0.457 16 1.7x0.486 17 1.8x0.514 18 1.9x0.543 19 2x0.571 20
0.03-140 0.76x0.181, 12 Swiss 0.033-140 0.84x0.181, 11 Swiss 0.034-110 0.86x0.231, 10 Swiss 0.035-110 0.89x0.231, 10A Swiss 0.036-113 0.91x0.225, 10 US 0.036-110 0.91x0.231, 10B 0.039-110 0.99x0.231, 9 Swiss 0.041-120 1.03x0.212, 9 Elgin 0.043-100 1.09x0.254, 8 0.047-110 1.19x0.231, 3, 6, 7 0.051-84 1.29x0.302, 4 0.054-84 1.36x0.302, 5 0.058-84 1.47x0.302, 2 (pin lever) 0.06-80 1.55x0.318, 2 (pocket) 0.074-72 1.88x0.353, 1 0.89-60 2.26x0.423, 0
2.58-90 10/0, 2.58x0.282 3.2-80 5/0, 3.2x0.318 3.9-66 0, 3.9x0.385 4.4-66 12-6, 4.4x0.385 5-60 16, 5x0.423 5.9-50 18, 5.9x0.508
1.2-110 5/0-10/0, 1.2x0.231 1.53-80 12-6-0, 1.53x0.318 1.93-72 16, 1.93x0.353 2.28-60 18.0, 2.28x0.423
0.35-254 23, 0.35x0.1 0.45-240 21, 0.45x0.106 0.55-220 19, 0.55x0.115 0.65-200 17, 0.65x0.127 0.83-180 15, 0.83x0.141 0.93-160 9, 0.93x0.159 1-180 13, 1x0.141 1-140 7, 1x0.181 1.1-120 5, 1.1x0.212 1.2-110 3, 1.2x0.231 1.34-170 11, 1.34x0.149 1.5-110 1, 1.5x0.231
0.0132-360 0.33x0.0112 0.0148-320 0.37x0.012 0.0168-260 0.42x0.0132 0.0208-220 0.52x0.0168 0.0228-260 0.57x0.0188 0.0248-220 0.62x0.02 0.0268-180 0.67x0.022 0.0288-220 0.72x0.0248 0.0308-180 0.77x0.0248 0.0308-220 0.77x0.0268 0.0368-140 0.92x0.028 0.0368-220 0.92x0.0268 0.0408-120L 1.02x0.03 0.0408-200 1.02x0.0348 0.0428-120 1.07x0.0328 0.0448-110 1.12x0.034 0.0468-110 1.17x0.0348 0.0488-140 1.22x0.04 0.0488-200 1.22x0.0436 0.0508-110L 1.27x0.0388 0.0548-180 1.37x0.0488 0.0608-110 1.52x0.0488 0.0608-110L 1.52x0.0488 0.0708-180L 1.77x0.0648 0.0768-110L 1.92x0.0708 0.0772-80L 1.93x0.0612 0.0892-80L 2.23x0.0712
H 0.254x0.072 Swiss screw thread, historical, size 25, 0.01-353.8 H 0.289x0.080 Swiss screw thread, historical, size 24, 0.0114-318.3 H 0.328x0.089 Swiss screw thread, historical, size 23, 0.0129-286.7 H 0.372x0.099 Swiss screw thread, historical, size 22, 0.0146-257.9 H 0.426x0.109 Swiss screw thread, historical, size 21, 0.0168-233 H 0.479x0.122 Swiss screw thread, historical, size 20, 0.0189-208.2 H 0.543x0.135 Swiss screw thread, historical, size 19, 0.0214-188.1 H 0.616x0.150 Swiss screw thread, historical, size 18, 0.0243-169.3 H 0.699x0.167 Swiss screw thread, historical, size 17, 0.0275-152.1 H 0.794x0.185 Swiss screw thread, historical, size 16, 0.0313-137.3 H 0.901x0.206 Swiss screw thread, historical, size 15, 0.0355-123.3 H 1.102x0.229 Swiss screw thread, historical, size 14, 0.0434-110.9 H 1.16x0.254 Swiss screw thread, historical, size 13, 0.0457-100 H 1.32x0.282 Swiss screw thread, historical, size 12, 0.052-90.1 H 1.49x0.314 Swiss screw thread, historical, size 11, 0.0587-80.9 H 1.64x0.349 Swiss screw thread, historical, size 10, 0.0646-72.8 H 1.92x0.387 Swiss screw thread, historical, size 9, 0.0756-65.6 H 2.18x0.430 Swiss screw thread, historical, size 8, 0.0858-59.1 H 2.48x0.478 Swiss screw thread, historical, size 7, 0.0976-53.1 H 2.81x0.531 Swiss screw thread, historical, size 6, 0.1106-47.8 H 3.19x0.590 Swiss screw thread, historical, size 5, 0.1256-43.1 H 3.62x0.656 Swiss screw thread, historical, size 4, 0.1425-38.7 H 4.11x0.729 Swiss screw thread, historical, size 3, 0.1618-34.8 H 4.66x0.810 Swiss screw thread, historical, size 2, 0.1835-31.4 H 5.29x0.900 Swiss screw thread, historical, size 1, 0.2083-28.2 H 6x1.000 Swiss screw thread, historical, size 0, 0.2362-25.4 H 6.81x1.100 Swiss screw thread, historical, size -1, 0.2681-23.1 H 7.73x1.230 Swiss screw thread, historical, size -2, 0.3043-20.7 H 8.77x1.370 Swiss screw thread, historical, size -3, 0.3453-18.5 H 9.95x1.520 Swiss screw thread, historical, size -4, 0.3917-16.7 H 11.3x1.690 Swiss screw thread, historical, size -5, 0.4449-15 H 12.8x1.880 Swiss screw thread, historical, size -6, 0.5039-13.5 H 14.5x2.090 Swiss screw thread, historical, size -7, 0.5709-12.2 H 16.5x2.320 Swiss screw thread, historical, size -8, 0.6496-10.9 H 18.7x2.580 Swiss screw thread, historical, size -9, 0.7362-9.8 H 21.2x2.870 Swiss screw thread, historical, size -10, 0.8346-8.9 H 24.11x3.190 Swiss screw thread, historical, size -11, 0.9492-8 H 27.4x3.540 Swiss screw thread, historical, size -12, 1.0787-7.2 H 31x3.930 Swiss screw thread, historical, size -13, 1.2048-6.5 H 35.2x4.370 Swiss screw thread, historical, size -14, 1.3858-5.8 H 40x4.860 Swiss screw thread, historical, size -15, 1.5748-5.2 H 45.4x5.400 Swiss screw thread, historical, size -16, 1.7874-4.7 H 51.5x6.000 Swiss screw thread, historical, size -17, 2.0276-4.2 H 58.4x6.660 Swiss screw thread, historical, size -18, 2.2992-3.8 H 66.3x7.400 Swiss screw thread, historical, size -19, 2.6102-3.4 H 75.2x8.230 Swiss screw thread, historical, size -20, 2.9606-3.1
H 0.148-32 gas (brass pipe) thread, size 0.148", 3.759x0.794 H 0.196-32 gas (brass pipe) thread, size 0.196", 4.978x0.794 H 0.246-27 gas (brass pipe) thread, size No.4", 6.248x0.941 H 0.26-27 gas (brass pipe) thread, size 1/4", 6.604x0.941 H 0.342-27 gas (brass pipe) thread, size 5/16", 8.687x0.941 H 0.39-27 gas (brass pipe) thread, size 3/8", 9.906x0.941 H 0.459-27 gas (brass pipe) thread, size 7/16", 11.659x0.941 H 0.515-27 gas (brass pipe) thread, size 1/2", 13.081x0.941 H 0.578-27 gas (brass pipe) thread, size 9/16", 14.681x0.941 H 0.637-27 gas (brass pipe) thread, size 5/8", 16.18x0.941 H 0.77-27 gas (brass pipe) thread, size 3/4", 19.558x0.941 H 0.885-27 gas (brass pipe) thread, size 7/8", 22.479x0.941 H 1.006-27 gas (brass pipe) thread, size 1", 25.552x0.941
H 3/8(-24) Admiralty thread, 9.525x1.058 H 7/16(-24) Admiralty thread, 11.113x1.058 H 1/2(-20) Admiralty thread, 12.7x1.270 H 9/16(-20) Admiralty thread, 14.111x1.270 H 5/8(-20) Admiralty thread, 15.875x1.270 H 11/16(-20) Admiralty thread, 17.463x1.270 H 3/4(-14) Admiralty thread, 19.05x1.814 H 13/16(-14) Admiralty thread, 20.638x1.814 H 7/8(-14) Admiralty thread, 22.225x1.814 H 15/16(-14) Admiralty thread, 23.813x1.814 H 1(-12) Admiralty thread, 25.4x2.117 H 1.1/16(-12) Admiralty thread, 26.988x2.117 H 1.1/8(-12) Admiralty thread, 28.575x2.117 H 1.3/16(-12) Admiralty thread, 30.163x2.117 H 1.1/4(-12) Admiralty thread, 31.75x2.117 H 1.5/16(-12) Admiralty thread, 33.338x2.117 H 1.3/8(-12) Admiralty thread, 34.925x2.117 H 1.7/16(-12) Admiralty thread, 36.513x2.117 H 1.1/2(-12) Admiralty thread, 38.1x2.117
@ 0.01-400 Whitworth Instrument, size 10, 0.254x0.064 @ 0.011-400 Whitworth Instrument, size 11, 0.279x0.064 @ 0.012-350 Whitworth Instrument, size 12, 0.305x0.073 @ 0.013-350 Whitworth Instrument, size 13, 0.33x0.073 @ 0.014-300 Whitworth Instrument, size 14, 0.356x0.085 @ 0.016-300 Whitworth Instrument, size 16, 0.406x0.085 @ 0.017-250 Whitworth Instrument, size 17, 0.432x0.102 @ 0.018-250 Whitworth Instrument, size 18, 0.457x0.102 @ 0.019-250 Whitworth Instrument, size 19, 0.483x0.102 @ 0.02-210 Whitworth Instrument, size 20, 0.508x0.121 @ 0.022-210 Whitworth Instrument, size 22, 0.559x0.121 @ 0.024-210 Whitworth Instrument, size 24, 0.61x0.121 @ 0.026-180 Whitworth Instrument, size 26, 0.66x0.141 @ 0.028-180 Whitworth Instrument, size 28, 0.711x0.141 @ 0.03-180 Whitworth Instrument, size 30, 0.762x0.141 @ 0.032-180 Whitworth Instrument, size 32, 0.813x0.141 @ 0.034-150 Whitworth Instrument, size 34, 0.864x0.169 @ 0.036-150 Whitworth Instrument, size 36, 0.914x0.169 @ 0.038-120 Whitworth Instrument, size 38, 0.965x0.212 @ 0.04-120 Whitworth Instrument, size 40, 1.016x0.212 @ 0.045-120 Whitworth Instrument, size 45, 1.143x0.212 @ 0.05-100 Whitworth Instrument, size 50, 1.27x0.254 @ 0.055-100 Whitworth Instrument, size 55, 1.397x0.254 @ 0.06-100 Whitworth Instrument, size 60, 1.524x0.254 @ 0.065-80 Whitworth Instrument, size 65, 1.651x0.318 @ 0.07-80 Whitworth Instrument, size 70, 1.778x0.318 @ 0.075-80 Whitworth Instrument, size 75, 1.905x0.318 @ 0.08-60 Whitworth Instrument, size 80, 2.032x0.423 @ 0.085-60 Whitworth Instrument, size 85, 2.159x0.423 @ 0.09-60 Whitworth Instrument, size 90, 2.286x0.423 @ 0.09-50 Whitworth Instrument, size 95, 2.286x0.508 @ 0.1-50 Whitworth Instrument, size 100, 2.54x0.508
http://www.oldengine.org/members/diesel/Tables/copper1.htm @ 0.248(-28) copper pipe thread, 1/8" inner dia; W6.3x0.907 @ 0.389(-20) copper pipe thread, 1/4" inner dia; W9.88x1.27 @ 0.514(-20) copper pipe thread, 3/8" inner dia; W13.05x1.27 @ 0.639(-20) copper pipe thread, 1/2" inner dia; W16.23x1.27 @ 0.764(-20) copper pipe thread, 5/8" inner dia; W19.41x1.27 @ 0.889(-20) copper pipe thread, 3/4" inner dia; W22.58x1.27 @ 1.104(-20) copper pipe thread, 7/8" inner dia; W28.04x1.27 @ 1.155(-20) copper pipe thread, 1" inner dia; W29.34x1.27 @ 1.405(-20) copper pipe thread, 1-1/4" inner dia; W35.69x1.27 @ 1.655(-20) copper pipe thread, 1-1/2" inner dia; W42.04x1.27 @ 1.929(-16) copper pipe thread, 1-3/4" inner dia; W49.00x1.59 @ 2.179(-16) copper pipe thread, 2" inner dia; W55.35x1.59x1.59 @ 2.429(-16) copper pipe thread, 2-1/4" inner dia; W61.70x1.59 @ 2.679(-16) copper pipe thread, 2-1/2" inner dia; W68.05x1.59 @ 2.929(-16) copper pipe thread, 2-3/4" inner dia; W74.40x1.59 @ 3.203(-16) copper pipe thread, 3" inner dia; W81.36x1.59
@ 1/2-18 B.S. electrical conduit thread, Whitworth, 55deg @ 5/8-18 B.S. electrical conduit thread, Whitworth, 55deg @ 3/4-16 B.S. electrical conduit thread, Whitworth, 55deg @ 1-16 B.S. electrical conduit thread, Whitworth, 55deg @ 1.1/4-16 B.S. electrical conduit thread, Whitworth, 55deg @ 1.1/2-14 B.S. electrical conduit thread, Whitworth, 55deg @ 2-14 B.S. electrical conduit thread, Whitworth, 55deg @ 2.1/2-14 B.S. electrical conduit thread, Whitworth, 55deg BSW,BSF 1.1/8-7,9 1.1/4-7,9 1.3/8-(6),8 1.1/2-6,8 1.5/8-(5),8 1.3/4-5,7 1.7/8-(4.5) 2-(4.5),7 2.1/8-(4.5) 2.1/4-4,6 2.3/8-(4) 2.1/2-4,6 2.5/8-(4) 2.3/4-3.5,6 2.7/8-(3.5) 3-3.5,5 3.1/8-(3.5) 3.1/4-3.25,5 3.3/8-(3.25) 3.1/2-3.25,4.5 3.5/8-(3.25) 3.3/4-3,4.5 3.7/8-(3) 4-3,4.5 4.1/8-(3) 4.1/4-(2.875),4 4.3/8-(2.875) 4.1/2-(2.875) 4.3/4-(2.75) 5-(2.75) 5.1/4-(2.375) 5.1/2-(2.375) 5.3/4-(2.375) 6-(2.375)
0.056-62 0.064-62 0.072-62 0.08-62 0.092-56 0.104-44 1/8-40 0.154-40 5/32-32 0.175-32 3/16-32 7/32-26 1/4-26 17/64-26 9/32-26 5/16-26 3/8-26 7/16-26 1/2-26 9/16-26 0.9675-30 1-26 1.29-24 left 1.37-24 1.7/16-24 left 1.1/2-24 H 0.056-62 CEI Original Cycle, British bicycles, historical H 0.064-62 CEI Original Cycle, British bicycles, historical H 0.072-62 CEI Original Cycle, British bicycles, historical H 0.08-62 CEI Original Cycle, British bicycles, historical H 0.092-56 CEI Original Cycle, British bicycles, historical H 0.104-44 CEI Original Cycle, British bicycles, historical H 1/8-40 CEI Original Cycle, British bicycles, historical H 0.154-40 CEI Original Cycle, British bicycles, historical H 5/32-32 CEI Original Cycle, British bicycles, historical H 0.175-32 CEI Original Cycle, British bicycles, historical H 3/16-32 CEI Original Cycle, British bicycles, historical H 7/32-26 CEI Original Cycle, British bicycles, historical H 1/4-26 CEI Original Cycle, British bicycles, historical H 17/64-26 CEI Original Cycle, British bicycles, historical H 9/32-26 CEI Original Cycle, British bicycles, historical H 5/16-26 CEI Original Cycle, British bicycles, historical H 3/8-26 CEI Original Cycle, British bicycles, historical H 7/16-26 CEI Original Cycle, British bicycles, historical H 1/2-26 CEI Original Cycle, British bicycles, historical H 9/16-26 CEI Original Cycle, British bicycles, historical H 0.9675-30 CEI Original Cycle, British bicycles, historical H 1-26 CEI Original Cycle, British bicycles, historical H 1.37-24 CEI Original Cycle, British bicycles, historical H 1.1/2-24 CEI Original Cycle, British bicycles, historical H 1.29-24 CEI left H 1.7/16-24 CEI left
0.0825-56 0.0905-56 0.1025-56 0.1145-56 1/8-40 0.1291-44 0.1423-40 5/32-32 0.1583-40 0.1776-32 3/16-32 7/32-26 1/4-24 17/64-26 9/32-26 5/16-26 3/8-26 7/16-26 1/2-26 9/16-26 5/8-26 11/16-26 3/4-26 7/8-24 31/32-30 1-24 1.1/8-26 1.29-24 left 1.9/16-24 1.5/8-24 @ 0.0825-56 BSC British Standard Cycle, bicycles; less common size? @ 0.0905-56 BSC British Standard Cycle, bicycles; less common size? @ 0.1025-56 BSC British Standard Cycle, bicycles; less common size? @ 0.1145-56 BSC British Standard Cycle, bicycles; less common size? @ 1/8-40 BSC British Standard Cycle, bicycles @ 0.1291-44 BSC British Standard Cycle, bicycles; less common size? @ 0.1423-40 BSC British Standard Cycle, bicycles; less common size? @ 5/32-32 BSC British Standard Cycle, bicycles @ 0.1583-40 BSC British Standard Cycle, bicycles; less common size? @ 0.1776-32 BSC British Standard Cycle, bicycles; less common size? @ 3/16-32 BSC British Standard Cycle, bicycles @ 7/32-26 BSC British Standard Cycle, bicycles @ 1/4-24 BSC British Standard Cycle, bicycles @ 17/64-26 BSC British Standard Cycle, bicycles @ 9/32-26 BSC British Standard Cycle, bicycles @ 5/16-26 BSC British Standard Cycle, bicycles @ 3/8-26 BSC British Standard Cycle, bicycles @ 7/16-26 BSC British Standard Cycle, bicycles @ 1/2-26 BSC British Standard Cycle, bicycles @ 9/16-26 BSC British Standard Cycle, bicycles @ 5/8-26 BSC British Standard Cycle, bicycles @ 11/16-26 BSC British Standard Cycle, bicycles @ 3/4-26 BSC British Standard Cycle, bicycles @ 7/8-24 BSC British Standard Cycle, bicycles @ 31/32-30 BSC British Standard Cycle, bicycles @ 1-24 BSC British Standard Cycle, bicycles @ 1.1/8-26 BSC British Standard Cycle, bicycles @ 1.29-24 BSC left British Standard Cycle, bicycles @ 1.9/16-24 BSC British Standard Cycle, bicycles @ 1.5/8-24 BSC British Standard Cycle, bicycles
1/8 0.405 1/4 0.540 3/8 0.675 1/2 0.840 3/4 1.050 1 1.315 1.1/4 1.660 1.1/2 1.900 2 2.375 2.1/2 2.875 3 3.500 3.1/2 4.000 4 4.500 5 5.563 6 6.625 8 8.625 10 10.75 12 12.75 14 14.00 16 16.00 18 18.00 20 20.00 22 22.00 24 24.00
NPS 5/8, DN 18, ASTM copper 18mm NPS 4.1/2, DN 115, AWWA 114.3
Whitworth, Heilmann-Ducommun, and Steinlen, Armengaud, Bodmer, Reuleux, and Redtenbacher many systems use pitch as basis of stepping, with 1mm as base, to which 6mm dia matches best; explains prevalence of M6x1
http://www.thecrosbygroup.com/html/en/pdf/pgs/145.pdf thread hook/gate no. max load (tons) 1/2-13 UNC #2 .90 9/16-12 UNC #3 1.27 5/8-11 UNC #4 1.54 3/4-10 UNC #5 2.09 7/8-9 UNC #6 3.63 1-8 UNC #7 3.81 1.1/8-7 UNC #8 5.00 1.1/4-7 UNC #9 6.53 1.1/2-6 UNC #11 8.35 1.5/8-5.5 UNC #12 11.15 1.3/4-5 UNC #13 13.6 2-4.5 UNC #14 16.8 2.3/4-4 UNC #16/#16A 22.4/29.4 4-4 UNC #17/#17A 44.9/59.5 1 .45 — — — — 11 8.35 38 1-1/2 - 6 UNC 7.9 7.8/8.10 2 .90 12.70 1/2 - 13 UNC 3.2 3.15/3.30 12 11.15 41.2 1-5/8 - 5-1/2 UNC 7.9 7.8/8.10 3 1.27 14.20 9/16 - 12 UNC 3.2 3.15/3.30 13 13.6 44.4 1-3/4 - 5 UNC 9.5 9.40/9.7 4 1.54 15.80 5/8 - 11 UNC 3.2 3.15/3.30 14 16.8 50.7 2 - 4-1/2 UNC 9.5 9.40/9.7 5 2.09 19.00 3/4 - 10 UNC 4.0 3.94/4.05 16 22.4 69.8 2-3/4 - 4 UNC 12.7 12.5/12.95 6 3.63 22.20 7/8 - 9 UNC 4.75 4.70/4.90 16-A 29.9 69.8 2-3/4 - 4 UNC 12.7 12.5/12.95 7 3.81 25.30 1 - 8 UNC 4.75 4.70/4.90 17 44.9 101.5 4 - 4 UNC 19.1 18.9/19.30 8 5.00 28.50 1-1/8 - 7 UNC 6.35 6.25/6.50 17-A 59.9 101.5 4 - 4 UNC 19.1 18.9/19.30 9 6.53 31.70 1-1/4 - 7 UNC 6.35 6.25/6.50 — — — — — — 1/2-13 UNC on crane hooks; minimum size for #2 hook/crane, workload limit .90 tons (Crosby/Bullard) 9/16-12 UNC on crane hooks; minimum size for #3 hook/crane, workload limit 1.27 tons (Crosby/Bullard) 5/8-11 UNC on crane hooks; minimum size for #4 hook/crane, workload limit 1.54 tons (Crosby/Bullard) 3/4-10 UNC on crane hooks; minimum size for #5 hook/crane, workload limit 2.09 tons (Crosby/Bullard) 7/8-9 UNC on crane hooks; minimum size for #6 hook/crane, workload limit 3.63 tons (Crosby/Bullard) 1-8 UNC on crane hooks; minimum size for #7 hook/crane, workload limit 3.81 tons (Crosby/Bullard) 1.1/8-7 UNC on crane hooks; minimum size for #8 hook/crane, workload limit 5.00 tons (Crosby/Bullard) 1.1/4-7 UNC on crane hooks; minimum size for #9 hook/crane, workload limit 6.53 tons (Crosby/Bullard) 1.1/2-6 UNC on crane hooks; minimum size for #11 hook/crane, workload limit 8.35 tons (Crosby/Bullard) 1.5/8-5.5 UNC on crane hooks; minimum size for #12 hook/crane, workload limit 11.15 tons (Crosby/Bullard) 1.3/4-5 UNC on crane hooks; minimum size for #13 hook/crane, workload limit 13.6 tons (Crosby/Bullard) 2-4.5 UNC on crane hooks; minimum size for #14 hook/crane, workload limit 16.8 tons (Crosby/Bullard) 2.3/4-4 UNC on crane hooks; minimum size for #16/#16A hook/crane, workload limit 22.4/29.4 tons (Crosby/Bullard) 4-4 UNC on crane hooks; minimum size for #17/#17A hook/crane, workload limit 44.9/59.5 tons (Crosby/Bullard)
Army Ammunition Data Sheets for Land Mines (FSC 1345). TM-43-001-36 0.4375-20 UNC-2A small firing devices 0.5625-12 UNC-1A standard firing devices, common grenade/mine fuze 0.75-18 UNS 3/4-18 secondary fuze well 0.6875-12 NC 11/16-12 secondary fuze well 1.375-18 NEF-2A booster cavity 0.5625-12 UNC female, 0.75-18 UNS male or 0.6875-12 male - on booster charges for antitank mines 0.75" - M1,M2 boosters/activators for mines, typ. secondary/boobytrap/antitamper fuzes 0.5625-12 detonator holder assembly on antitank mine fuze M606 (10" diameter wheel) 0.5625-12 - initiator well on M4 Burster, igniter; on M6A1 antipersonnel mine fuze, M10 mine fuzes 0.625-11 UNC-1A M605 fuze for M16 mines 0.75-12 NS-2A M607 fuze for M21 antitank mines 2.3125-14 UNS-1A M608 fuze for M6A2 and M15 antitank mines, M23 chemical mine; M624 fuze for M15 mine (M607 fuze+adapter) 2.3125-14+0.6875-12 on chemical mines 2.3125-14+0.75-12 on M15 antitank mine, fuze wells 0.5625-12+0.75-18 on M19 nonmetallic antitank mine 1.375-18+0.75-?? on M21 antitank mine 0.5625-12 on M2A4 bouncing antipersonnel mine; on M3 antipersonnel mine; on M18A1 "claymore" 0.4375-20 on M14 antipersonnel mine 0.625-11 on M16 mines 0.6875-12 NS SPEC + 0.5625-12 NS SPEC male/female adapter for fuze for practice mines https://www.practicalmachinist.com/vb/general/uk-source-used-7-8-bspt-tap-256705/ 7/8"-14 BSPT fuze well on old (1890's) artillery shells 7/8-14 BSW(?) primer threads on brass shell cases http://www.corbins.com/kit-224.htm 7/8-14 common reloading press dies W M10 friction igniter for pyrotechnics, male on igniter, TZ-2, Czechoslovak W M12 friction igniter for pyrotechnics, male on igniter, TZ-M, Czechoslovak W M12 electrical igniters, male on igniter (as "sleeve bolt", loose with wires through the center), EPIC/EPIO/EPIP, Czechoslovak; igniter itself 7mm dia, 47mm long W 0.4375-20 UNC-2A 7/16-20, on US mines/grenades, small fuzes/initiators; eg. on M14 antipersonnel mine W 0.5625-12 UNC-1A 9/16-12, on US mines/grenades, most common fuze/initiator; eg. M19 nonmetallic antitank mine, often with 0.75-18 or 0.6875-12 as secondary fuze well, or 9/16 f to 11/16 or 1/2 m for booster/activator W 0.625-11 UNC-1A 5/8-11, on US mines/grenades, eg. M605 fuze for M16 mines; eg. M605 fuze for M16 mines W 0.6875-12 NC 11/16-12, on US mines, common as secondary fuze well (also can be 0.75-18, 0.75-12); eg. on chemical mines, with 2.3125-14 W 0.75-18 UNS 3/4-18, on US mines, common as secondary fuze well (also can be 0.75-12, 0.6875-12); eg. on M19 mine with 0.5625-12 W 0.75-12 NS-2A 3/4-12, on US mines, eg. M607 fuze on M21 antitank mine; common as secondary fuze well (also can be 0.75-18, 0.6875-12); eg. on M15 antitank mine with 2.3125-14 W 1.375-18 NEF-2A 1.3/8-18, on US mines; booster cavity on M21 antitank mine W 2.3125-14 UNS-1A 2.5/16-14, on US mines; common large fuze, eg. M608 fuze on M6 and M15 antitank ines, M23 chemical mine; M624 fuze (M607 fuze in adapter) W 7/8-14 BSW(?) primer threads on old British brass shell cases? W 7/8-14 BSPT fuze well on old (1890's) British artillery shells http://www.geocities.ws/toy_bienn/robe-espoletas.html M10x1 LH WW2 German artillery fuze, point detonation, in tip, standard for 2cm/3cm HE/HEI flak and aircraft cannon grenades, female for booster pellet; also M15x1 for grenade body M13x1 LH WW2 German artillery fuze, Bd.Z.1513, in grenade base, for AP 2cm aircraft gun shells M15x1 WW2 German artillery fuze, point detonation, in tip, standard for 2cm/3cm HE/HEI/HC flak and aircraft cannon grenades, external; also M10x1 LH female for booster pellet M22x1.5 LH WW2 German artillery fuze, Bd.Z.5103*, in grenade base, for armor piercing 3.7cm, 5cm, 7.5cm, 7.62cm M25x1.5 WW2 German artillery fuze, 3,7cm Bd.Z.P34(t), base fuze, for AP 3,7cm Pzgr.34 (t) W39-10 WW2 German artillery fuze, Bd.Z.C/38, in grenade base, for capped HE Navy Shells 15cm, 21cm, 24cm, 28cm, 30.5cm, 38cm, 40.5cm M40x2 WW2 German artillery fuze, Bd.Z.f.15cm Gr.19 Be, in grenade base, armor piercing high explosive 15cm/21cm grenades M46x3 WW2 German artillery fuze, Bd.Z.f.10cm Pzgr., in grenade base, armor piercing high explosive 10cm/10.5cm grenades M46x3 WW2 German artillery fuze, Bd.Z.f.7,5cm Pzgr., in grenade base, armor piercing high explosive 7.5cm grenades M54x3 WW2 German artillery fuze, Bd.f.8,8cm Pzgr., in grenade base, armor piercing high explosive 8.8cm grenades M28x1.5 WW2 German artillery fuze, 3,7cm Kpf.Z.Zerl.P/Fg/Pv, point detonation self destruction, in tip, for HE/HEI shells 3,7cm Flak 18 and 36 M50x3 E.Kz.C/28, point detonation, HE navy shells 7.5cm, 8.8cm and 10.5cm M40x2 Kz C/36, point detonation, TP navy shells 8.8cm 50-8 Kz C/27 (Lm), point detonation, capped HE Navy Shells 12,7cm, 15cm, 20,3cm, 21cm, 28cm and 30,5cm W M10x1 LH WW2 German artillery fuze, point detonation, in tip, standard for 2cm/3cm HE/HEI flak and aircraft cannon grenades, female for booster pellet; also M15x1 for grenade body W M13x1 LH WW2 German artillery fuze, Bd.Z.1513, in grenade base, for AP 2cm aircraft gun shells W M15x1 WW2 German artillery fuze, point detonation, in tip, standard for 2cm/3cm HE/HEI/HC flak and aircraft cannon grenades, external; also M10x1 LH female for booster pellet W M22x1.5 LH WW2 German artillery fuze, Bd.Z.5103*, in grenade base, for armor piercing 3.7cm, 5cm, 7.5cm, 7.62cm W M25x1.5 WW2 German artillery fuze, 3,7cm Bd.Z.P34(t), base fuze, for AP 3,7cm Pzgr.34 (t) W W39-10 WW2 German artillery fuze, Bd.Z.C/38, in grenade base, for capped HE Navy Shells 15cm, 21cm, 24cm, 28cm, 30.5cm, 38cm, 40.5cm W M40x2 WW2 German artillery fuze, Bd.Z.f.15cm Gr.19 Be, in grenade base, armor piercing high explosive 15cm/21cm grenades W M46x3 WW2 German artillery fuze, Bd.Z.f.10cm Pzgr., in grenade base, armor piercing high explosive 10cm/10.5cm grenades W M46x3 WW2 German artillery fuze, Bd.Z.f.7,5cm Pzgr., in grenade base, armor piercing high explosive 7.5cm grenades W M54x3 WW2 German artillery fuze, Bd.f.8,8cm Pzgr., in grenade base, armor piercing high explosive 8.8cm grenades W M28x1.5 WW2 German artillery fuze, 3,7cm Kpf.Z.Zerl.P/Fg/Pv, point detonation self destruction, in tip, for HE/HEI shells 3,7cm Flak 18 and 36 W M50x3 WW2 German artillery fuze, E.Kz.C/28, point detonation, in tip, HE navy shells 7.5cm, 8.8cm and 10.5cm W M40x2 WW2 German artillery fuze, Kz C/36, point detonation, in tip,, TP navy shells 8.8cm W 50-8 WW2 German artillery fuze, Kz C/27 (Lm), point detonation, in tip,, capped HE Navy Shells 12,7cm, 15cm, 20,3cm, 21cm, 28cm and 30,5cm AZ 1532, artillery fuze for grenade tip, point detonation, HE 13mm for aircraft MG 131/13, external thread; also M10x1 LH female for booster pellet M10x1 LH WW2 German artillery fuze, AZ 1532, artillery fuze for grenade tip, point detonation, HE 13mm for aircraft MG 131/13, internal thread for booster pellet; also M15x1 for screwing to grenade also: 2cm Kpf.Z.45, for HE, HEI 2cm Flak 28/29, Flak 30/38, Flakvierling, Flak Madsen also: AZ 47, for HE, HEI 2cm Flak 28/29, Flak 30/38, Flakvierling, Flak Madsen AZ 49, point detonation, HE, HEI 2cm Flak 30/38 und Flakvierling AZ 48, point detonation, HE, HEI 2cm Flak 30/38 und Flakvierling 2cm Kpf.Z.Zerl.Fg., Point detonation self destruction, for HE, HEI 2cm Flak 28/29, Flak 30/38, Flakvierling also: ZZ 1505A, Point detonation self destruction, Mine shells (HC) 2cm for aircraft guns MG FF/FFM and MG 151/20 also: ZZ 1589A, Point detonation self destruction, for Mine shells (HC) 3cm for aircraft guns MK 101, MK 103 and MK 108 https://bulletpicker.com/pdf/TM%2043-0001-28,%20Artillery%20Ammunition.pdf 1.02-1SNS-3 LH base detonating fuze M58, for 37mm subcaliber guns, practice 1.18-14 NS-2 point, MK27, for 40mm gun HE ammo 1.5-12 NS-1 point, M527, XM719, for 60mm mortar WP cartridges; M717, for 60mm mortar HE; M745, for 60mm smoke cartridge M722; M751, practice, for 81mm cartridge; 1.5-12 NS1 LH base detonating fuze M62, for 75 and 105mm recoilless rifle with HEAT and HEP cartridges; for 165mm guns with HEP cartridges 1.5-12 NS1 LH base detonating fuze M91, for 105mm howitzers with HEAT-T, or 106mm guns with HEP 1.5-12 UNF-1A timer/point, M776, on 60mm illumination cartridge M721; multioption, M734, for mortars 1.7-14 NS-2A point, M8, for 4.2inch mortar gas and smoke cartridges; point, M49, for 4.2inch mortar HE cartridges 1.7-14 NS-1 point, M503A2, for 57mm rifle ammo 1.7-14 NS-1 timer/point, M501, for 105mm and 155mm howitzers and 4.2in mortars 1.8-12 UNS-2A LH M534A1, for 105mm guns with HEP-T and W-T 1.8-12 UNS-2A M578, for 105mm cannons with HEP 1.8-16 UNS-1A timer, M592, for 106mm flechette-loaded cartridge M581 1.9-16 UNS-1A timer, M571, for 105mm flechette-loaded cartridge M494; M711, for flechette-loaded 90mm cartridge M580 2-12 NS-1 timer/point, M520, for 90 to 280mm cannons except 175mm 2-12 NS-1 timer/point, M548 2-12 NS-1 timer/point, M564, with 105mm/155mm/8in projectiles 2-12 UNS-1 timer, M562, for 4.2-inch mortars with illuminating shells "" timer, M565, for 105 to 8 inch cannons except 175mm 2-10 NS1 LH base detonating fuze M68, for 90mm gun 2.095-18 NS-1 female thread, point, M90, for 57mm HEAT projectile 2.4-18 NS-1 time, M84, for 81mm illuminating mortars 2-12 male, 1.7-14 female booster, M21A4 W 50-8 WW2 German artillery fuze, Kz C/27 (Lm), point detonation, in tip,, capped HE Navy Shells 12,7cm, 15cm, 20,3cm, 21cm, 28cm and 30,5cm W 1.18-14 NS-2 US artillery fuze, MK27, point detonation, for 40mm gun HE ammo W 1.5-12 NS-1 US artillery fuze, M527/XM719/M717/M745/M722, generally for 60mm mortars; M751, for 81mm mortars W 1.5-12 NS-1 LH US artillery fuze, base detonating, M62, for 75/105mm recoilless rifle HEAT-T cartridges, 165mm gun HEP cartridges; M91, base detonating, 105mm HEAT-T howitzers, 106mm HEP guns W 1.5-12 UNF-1A US artillery fuze, timer/point, M776 for 60mm illuminating cartridge M721, multioption M734 for mortars W 1.7-14 NS-1/2A US artillery fuze, point detonation, M8 for 3.2inch mortar gas/smoke cartridges, M49 for 4.2inch mortar HE, point M5302 for 57mm rifle ammo, timer/point M776 for illum M721, mutioption M734 for mortars W 1.8-16 UNS-1A US artillery fuze, timer M592 for 106mm flechette M581 W 1.8-12 UNS-2A LH US artillery fuze, M534A1 for 105mm gun HEP-T and W-T W 1.8-12 UNS-2A US artillery fuze, M578 for 105mm cannons with HEP W 1.9-16 UNS-1A US artillery fuze, timer M571 for 105mm flechette M494, M711 for flechette 90mm cartridge M580 W 2-12 NS-1 US artillery fuze, very common; timer/point M548, M520 for 90-180 (except 175mm) cannons; timer/point M564 for 105mm/155mm/8in projectiles; M562, 4.2in illum mortars; M565, 105mm-8in cannons W 2-10 NS-1 LH US artillery fuze, base detonating M68, for 90mm gun W 2.095-18 NS-1 US artillery fuze, point detonation, M90 for 57mm HEAT projectile; female thread, whole front cap W 2.4-18 NS-1 US artillery fuze, timer M84 for 81mm illuminating mortars
w 24x12.4. 24-2, dia 24mm, minor dia 16mm, length 135mm, square head, P49A sleeper screw, thread-rolled sleeper bolts: wood thread, attach rails to sleepers fish bolt: metal thread, attach fish plates to rails fish plates standards: GB standard BS standard, BS 47-1 JIS E standard, JIS E1102-2001 AREMA standard, AREMA2007; apertures 1.0625, 1.1875, 1.3125 UIC standard DIN standard http://www.railroadpart.com/rail-joints/fish-bolts.html Russian fish bolt: 27x160, GOST 11530 square head: M20, DIN5903-2 Type B button head oval neck, US: 1/2, 5/8, 3/4, 7/8, 1, 1.1/16, 1.1/8 diamond neck, US: 7/8 (4.5, 5.5 in long), 1 (5.25, 5.75 in long) standards: BS 20M, 30M, 35M, 35R, 50 O, 60A, 75R, 80R, 80A, 95RBH, and 113A; DIN S10, S14, S18, S20, S24, S30, S49, UIC54, UIC60; and AREMA 40ASCE, 60ASCE, 75ASCE, 90ARA, 115RE M20 fish bolt, square head, DIN5903-2 Type B http://railwayfasteningssuyu.sell.everychina.com/p-107692627-grade-8-8-bridge-railway-bolt-fish-bolts-for-fasten-rail-joints.html fish bolts: M18, M20, M22, M24 Cup head oval neck fish bolt, AS 1085.4,6,7 3/4", 13/16", 7/8",15/16",1", L=3-7/8", 4-3/8", 4-5/16", 5", 6-1/4" British standard track bolt, BS64 5/8"-1-1/2", Length1-1/2"-13 BHON track bolt, AREMA, SAE J429 15/16"-1-1/2", Length1-1/2"-13" BHDN track bolt, AREMA, SAE J429 A30, B30, A37, B37, A50, B50, B40N Day mark fish bolt, JIS E1107 7/8" x BSF4-7/8”, or BSW4-1/8" British standard track bolt, BS64 5/16" x BSF4-1/2", or BSW4-7/8" 5/16" x BSF4-1/2", or BSW4-7/8", BS64, Application areas: British countries 3/4"-1-1/8", Length1-1/2"-6-1/2" BHON track bolt, Square head frog bolt, AREMA, SAE J429 3/4"-1-3/8" Heavy Hex Head Frog Bolts, ASTM A325 anchor bolts: M16 to M48, L=100 to 500mm Anchor bolt, DIN529, ISO898-1, Anchored in concrete sleeper for K type fastening system. 30mm B30 Bolt for Metro http://www.rail-fastener.com/Track-Bolt.html 3/4", 13/16", 7/8",15/16",1", L=3-7/8", 4-3/8", 4-5/16", 5", 6-1/4" AGICO Track Bolt, British standard track bolt I, BS64 7/8" x BSF4-7/8”, or BSW4-1/8" AGICO Track Bolt, British standard track bolt II, BS64 15/16" x BSF4-1/2", or BSW4-7/8" AGICO Track Bolt, British standard track bolt III, BS64 M22, L=110mm, 120mm, M24, L=105 to 200mm German standard track bolt, DIN5903-2 Type C M20 German standard track bolt II, DIN5903-1 15/16 BSF railroads, fish bolt (on fish plates on rails); 4.7/8" long, AGICO track bolt, British standard track bolt, BS64 15/16 BSW railroads, fish bolt (on fish plates on rails); 4.1/8" long, AGICO track bolt, British standard track bolt, BS64 7/8 BSF railroads, fish bolt (on fish plates on rails); 4.7/8" long, AGICO track bolt, British standard track bolt, BS64 7/8 BSW railroads, fish bolt (on fish plates on rails); 4.1/8" long, AGICO track bolt, British standard track bolt, BS64 M18 railroads, insert bolt, anchored in concrete sleeper, with nuts/washers for spring blade fastening; NF F50-010 M18 railroads, fish bolt (on fish plates on rails); cup head oval neck fish bolt, AS 1085.4,6,7 M20 railroads, fish bolt (on fish plates on rails); cup head oval neck fish bolt, AS 1085.4,6,7 M20 railroads, fish bolt (on fish plates on rails); German standard track bolt, DIN 5903-1 M22 railroads, fish bolt (on fish plates on rails); German standard track bolt, DIN 5903-3 Type C, lengths 110/120mm M22 railroads, insert bolt, anchored in concrete sleeper, with nuts/washers for spring blade fastening; NF F50-010 M22 railroads, fish bolt (on fish plates on rails); cup head oval neck fish bolt, AS 1085.4,6,7 M24 railroads, fish bolt (on fish plates on rails); German standard track bolt, DIN 5903-3 Type C, lengths 105..200mm M24 railroads, fish bolt (on fish plates on rails); cup head oval neck fish bolt, AS 1085.4,6,7 M27 railroads, fish bolt (on fish plates on rails); Russian standard, 160mm long, GOST 11530
https://idaho.swagelok.com/AboutUs/~/media/Distributor%20Media/H-K/Idaho/Services/Thread%20Size.ashx Tube Size 1/16” 1/8” 3/16” 1/4” 5/16” 3/8” 1/2” 5/8” 3/4” 7/8” 1” ‘-1/4” 1-1/2” 2” Fitting Series 100 200 300 400 500 600 810 1010 1210 1410 1610 2000 2400 3200 % 3/16-32 NF Swagelok fittings, series 100, 1/16" tubes % 5/16-20 NC Swagelok fittings, series 200, 1/8" tubes % 3/8-20 NC Swagelok fittings, series 300, 3/16" tubes % 7/16-20 NF Swagelok fittings, series 400, 1/4" tubes % 1/2-20 NF Swagelok fittings, series 500, 5/16" tubes % 9/16-20 NF Swagelok fittings, series 600, 3/8" tubes % 3/4-20 NF Swagelok fittings, series 810, 1/2" tubes % 7/8-20 NF Swagelok fittings, series 1010, 5/8" tubes % 1-20 NF Swagelok fittings, series 1210, 3/4" tubes % 1.1/8-20 NF Swagelok fittings, series 1410, 7/8" tubes % 1.5/16-20 NF Swagelok fittings, series 1610, 1" tubes % 1.5/8-20 NS-3 Swagelok fittings, series 2000, 1.1/4" tubes % 1.15/16-20 UN-3 Swagelok fittings, series 2400, 1.1/2" tubes % 2.5/8-20 UN-3 Swagelok fittings, series 3200, 2" tubes % 7/16-20 NF Swagelok fittings, SAE/MS, heavy duty, series 400, 1/4" tubes % 9/16-18 NF Swagelok fittings, SAE/MS, heavy duty, series 400, 1/4" tubes % 7/16-20 NF Swagelok fittings, SAE/MS, heavy duty, series 600, 3/8" tubes % 9/16-18 NF Swagelok fittings, SAE/MS, heavy duty, series 600, 3/8" tubes % 7/16-20 NF Swagelok fittings, SAE/MS, heavy duty, series 800, 1/2" tubes % 9/16-18 NF Swagelok fittings, SAE/MS, heavy duty, series 800, 1/2" tubes % 7/16-20 NF Swagelok fittings, SAE/MS, heavy duty, 6mm/10mm/12mm tubes % 9/16-18 NF Swagelok fittings, SAE/MS, heavy duty, 6mm/10mm/12mm tubes % NPT 1/4 Swagelok fittings, NPT, 1/4" 3/8" 1/2" tubes % NPT 1/2 Swagelok fittings, NPT, 1/2" 3/4" 1" tubes % NPT 3/4 Swagelok fittings, NPT, 1" tubes % 1/4-28 UNF LH Swagelok fittings, medium-pressure cone-and-thread, 1/4" 6mm tubes % 3/8-24 UNF LH Swagelok fittings, medium-pressure cone-and-thread, 3/8" 10 tubes % 9/16-18 UNF LH Swagelok fittings, medium-pressure cone-and-thread, 1/2" 3/4" 12mm tubes % 3/4-16 UNF LH Swagelok fittings, medium-pressure cone-and-thread, 1" tubes % 1-14 UNF LH Swagelok fittings, medium-pressure cone-and-thread, 1" tubes Thread Size 3/16 - 32 NF 5/16 - 20 NC 3/8 - 20 NC 7/16 - 20 NF 1/2 - 20 NF 9/16 - 20 NF 3/4 - 20 NF 7/8 - 20 NF 1 - 20 NF 1-1/8 - 20 NF 1-5/16 - 20 NF 1-5/8 - 20 NS-3 1-15/16 - 20 UN-3 2-5/8 - 20 UN-3
tube: by outer diameter pipe: by inner diameter (outer dia is bigger) MTP: Model Taper Pipe, derived from NPT formulas UST: Universal Straight and Taper (P.M. Research Inc. Tapered Thread, compatible with straight UNS); pitch dia 0.005in larger than MTP, incompatible METP: Model Engineer Taper Pipe (British Equivalent of MTP)
@ 3/16-40 UST Universal Straight and Taper; for model steam engines, variant of MTP with 0.005" larger pitch diameter, incompatible with MTP, compatible with straight UNS; by P.M. Research Inc.
@ 1/4-40 UST Universal Straight and Taper; for model steam engines, variant of MTP with 0.005" larger pitch diameter, incompatible with MTP, compatible with straight UNS; by P.M. Research Inc. @ 1/4-32 MTP Model Taper Pipe; unusual pitch, on some Stuart Beam valves
3/16-32? 1/4-32? 5/16-24? 3/16-40 UST 1/4-40 UST PM Model: 3/16-40 UST/MTP/ME, 1/4-40 UST/MTP/ME, 1/4-32 ME, 5/16-27 MTP == 1/16 NPT Mini Steam: 3/16-40 UST/MTP, 1/4-40 UST/MTP, 5/16-27 MTP == 1/16 NPT common MTP sizes (Godshall's, American Model Engineering): 1/8-56, 5/32-48, 3/16-40, 1/4-40, 5/16-27; American Model Engineering: also 5/16-40, 3/8-40 MTP sizes (other vendor): 1/8-56, 5/32-48, 3/16-40, 1/4-40, 5/16-27, 5/16-40, 3/8-40 someone uses: 1/8 MTP, 1/4 MTP, 5/16 MTP other: MTP 1/8-56, 3/16-40, 1/4-40 and 5/16-27 1/4-32 rare, on Stuart Beam brass tap sets: 1/4x26 + 5/16x26 + 3/8x26 + 7/16x26 + 1/2x26 BSB
3/4-14 NGT 0,715x1/14 1:8 BS341 25T BS341 1991 W1” 1:8 BS341 1962 W19,8 DIN477 17E BS EN ISO 18T BS EN ISO W28,8 DIN477 25E BS EN ISO 1/2-14 NGT
7/16-28 UNEF backpacking canisters: popular resealables with 7/16-28 UNEF thread (male on canister), Lindal B188 valve, compatible with female EN 521 fittings, "universal EN417" canisters
EasyClic mounting similar but without thread [ ref]
https://www.ring-plug-thread-gages.com/PDChart/Tire-Valve-thread-data.html Vg5 5v1, 5.15x0.706, 0.2"-36 Vg5,2 5v2, 5.2x1.058, 0.2"-24 Vg6 6v1, 6x0.794, 0.235"-32, 15/64-32 Vg7,8 30 tpi Vg8 8v1, 7.7x0.794, 7.7-32 Vg9,6 10v1, 9.6x1 Vg10 10v2, 10.3x0.907, 0.405"-28 Vg12 12v1, 12.2x0.977, 0.48"-26
This International Standard specifies limit dimensions and tolerances for three series of tyre valve threads: — 5V1, 5V2, 6V1 and 8V1; — 9V1, 10V2, 12V1, 13V1; — 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, 17V3, 19V1 and 20V1. 60-deg angle [ ref] type also tpi pitch dia series 5v1 Vg5 36 0.705 5.2 1 .210-36 car-bike tire valve, Schrader/AV/American internal thread, 5.309x0.7056mm, also .209-26 5v2 Vg5,2 24 1.058 5.2 1 bicycle tire valve, Presta/SV/French/Sclaverland thread 6v1 Vg6 31.75 0.8 6.0 1 M6?, bicycle tire valve, Presta/SV/French/Sclaverland outer thread 8v1 Vg8 32 0.794 7.7 1 .305-32 car-bike tire valve, Schrader/AV/American external thread, most common cap size, 7.747x0.7938mm (8v1?); also Dunlop/DV/Woods/English bicycle tire valve 8v2 24 1.058 7.9 3 5/16-24 9v1 32 0.794 9.4 2 10v1 Vg9,6 25.4 1.0 9.6 3 10v2 Vg10 28 0.907 10.3 2 11v1 20 1.270 11.1 3 12v1 Vg12 26 0.977 12.2 2 .485-26 tire valve caps, less common large size, also .482-26 13v1 20 1.270 12.6 2 .500-20 13v2 32 0.794 12.7 3 15v1 25.4 1.0 15.0 3 M15x1? 16v1 27 0.941 15.8 3 17v1 25.4 1.0 17.0 3 M17x1? 17v2 24 1.058 17.5 3 17v3 16 1.588 17.5 3 19v1 16 1.588 19.0 3 20v1 25.4 1.0 20.5 3 M20.5x1? 5v1 tire valve, ISO 4570 series 1, 5.2x0.705 (36 tpi) 5v2 tire valve, ISO 4570 series 1, 5.2x1.058 (24 tpi) 6v1 tire valve, ISO 4570 series 1, 6.0x0.8 (M6?) 8v1 tire valve, ISO 4570 series 1, 7.7x0.794 (32 tpi) 8v2 tire valve, ISO 4570 series 3, 7.9x1.058 (24 tpi) 9v1 tire valve, ISO 4570 series 2, 9.4x0.794 (32 tpi) 10v1 tire valve, ISO 4570 series 3, 9.6x1.0 (25.4 tpi) 10v2 tire valve, ISO 4570 series 2, 10.3x0.907 (28 tpi) 11v1 tire valve, ISO 4570 series 3, 11.1x1.270 (20 tpi) 12v1 tire valve, ISO 4570 series 2, 12.2x0.977 (26 tpi) 13v1 tire valve, ISO 4570 series 2, 12.6x1.270 (20 tpi) 13v2 tire valve, ISO 4570 series 3, 12.7x0.794 (32 tpi) 15v1 tire valve, ISO 4570 series 3, 15.0x1.0 (25.4 tpi) 16v1 tire valve, ISO 4570 series 3, 15.8x0.941 (27 tpi) 17v1 tire valve, ISO 4570 series 3, 17.0x1.0 (25.4 tpi) 17v2 tire valve, ISO 4570 series 3, 17.5x1.058 (24 tpi) 17v3 tire valve, ISO 4570 series 3, 17.5x1.588 (16 tpi) 19v1 tire valve, ISO 4570 series 3, 19.0x1.588 (16 tpi) 20v1 tire valve, ISO 4570 series 3, 20.5x1.0 (25.4 tpi) tire designs: https://s3.amazonaws.com/ytc-prod/PDF/OTR_Library/otr_databook_2011.pdf liquid ballast can be added to tires to increase weight, lower center of gravity of tractors [ ref] (water (freezes), calcium chloride (corrosive but dense and cheap), beet juice (expensive), windshield washer fluid (not dense), antifreeze (expensive) usually about 75% fill CO2 is highly soluble in butyl rubber, tire inflated with a CO2 canister will quickly lose pressure air-inflated car tires lose about 1 psi (6.7kPa) per month, more at hot days weight capacity is pressure times volume
for thin brass tubes all 26 tpi, 55-deg 1/8(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1/4(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 3/8(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1/2(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 5/8(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 3/4(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 7/8(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1.1/8(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1.1/4(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 1.1/2(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 9/32(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 5/16(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 7/16(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg 9/16(-26) BSB British Standard Brass; for thin-walled brass tubes, 55-deg
Whitworth-based 1/8-40 ME Model Engineer, some model boiler fittings, rare 5/32-40 ME Model Engineer, some model boiler fittings, rare 3/16-40 ME Model Engineer, some model boiler fittings, rare 7/32-40 ME Model Engineer, some model boiler fittings, rare 1/4-40 ME Model Engineer, some model boiler fittings, rare 9/32-40 ME Model Engineer, some model boiler fittings, rare 5/16-40 ME Model Engineer, some model boiler fittings, rare 3/8-40 ME Model Engineer, some model boiler fittings, rare 7/16-40 ME Model Engineer, some model boiler fittings, rare 1/2-40 ME Model Engineer, some model boiler fittings, rare 1/8-32 ME Model Engineer, some model boiler fittings, rare 5/32-32 ME Model Engineer, some model boiler fittings, rare 3/16-32 ME Model Engineer, some model boiler fittings, rare 7/32-32 ME Model Engineer, some model boiler fittings, rare 1/4-32 ME Model Engineer, some model boiler fittings, rare 9/32-32 ME Model Engineer, some model boiler fittings, rare 5/16-32 ME Model Engineer, some model boiler fittings, rare 3/8-32 ME Model Engineer, some model boiler fittings, rare 7/16-32 ME Model Engineer, some model boiler fittings, rare 1/2-32 ME Model Engineer, some model boiler fittings, rare
BA 25 0.25x0.072, 47.5 deg, British Association standard, obsolete BA 24 0.29x0.080, 47.5 deg, British Association standard, obsolete BA 23 0.33x0.090, 47.5 deg, British Association standard, obsolete BA 22 0.37x0.098, 47.5 deg, British Association standard, obsolete BA 21 0.42x0.11, 47.5 deg, British Association standard, obsolete BA 20 0.48x0.12, 47.5 deg, British Association standard, obsolete BA 19 0.54x0.14, 47.5 deg, British Association standard, obsolete BA 18 0.62x0.15, 47.5 deg, British Association standard, obsolete BA 17 0.70x0.17, 47.5 deg, British Association standard, obsolete BA 16 0.79x0.19, 47.5 deg, British Association standard, obsolete BA 15 0.90x0.21, 47.5 deg, British Association standard, obsolete BA 14 1.00x0.23, 47.5 deg, British Association standard, obsolete BA 13 1.20x0.25, 47.5 deg, British Association standard, obsolete BA 12 1.30x0.28, 47.5 deg, British Association standard, obsolete BA 11 1.50x0.31, 47.5 deg, British Association standard, obsolete BA 10 1.70x0.35, 47.5 deg, British Association standard, obsolete BA 9 1.90x0.39, 47.5 deg, British Association standard, obsolete BA 8 2.20x0.43, 47.5 deg, British Association standard, obsolete BA 7 2.50x0.48, 47.5 deg, British Association standard, obsolete BA 6 2.80x0.53, 47.5 deg, British Association standard, obsolete BA 5 3.20x0.59, 47.5 deg, British Association standard, obsolete BA 4 3.60x0.66, 47.5 deg, British Association standard, obsolete BA 3 4.10x0.73, 47.5 deg, British Association standard, obsolete BA 2 4.70x0.81, 47.5 deg, British Association standard, obsolete BA 1 5.30x0.90, 47.5 deg, British Association standard, obsolete BA 0 6.00x1.00, 47.5 deg, British Association standard, obsolete
GL 8 (x2) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 10 (x2) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 12 (x2) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 14 (x2.5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 16 (x2.5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 18 (x3) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 20 (x3) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 22 (x3) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 25 (x3) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 25 (x3.5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 28 (x3) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 32 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 36 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 40 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 45 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 50 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 56 (x4) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 63 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 70 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 80 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 90 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 100 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 112 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external GL 125 (x5) on glass containers, knuckle thread DIN 168; 60deg internal, 30deg external ...also nonstandard:
GL 54 (x4?) GL 60 RD 10 RD 14 RD 48x3 RD 70x3 SVL 14 SVL 15 SVL 22 SVL 30 SVL 42 PP 28 some cell culture bottles
https://www.gewinde-normen.de/en/KS-KT-thread.html KS 10 (x2) for plastic containers, buttress thread DIN 6063-1, 40-deg KS 12 (x2) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KS 14 (x2.5) for plastic containers, buttress thread DIN 6063-1, 40-deg KS 16 (x2.5) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KS 18 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg KS 20 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KS 22 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg KS 24 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KS 25 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KS 26 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KS 28 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KS 30 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KS 32 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KS 36 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KS 40 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KS 45 (x4) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KS 50 (x4) for plastic containers, buttress thread DIN 6063-1, 30-deg KS 60 (x6) for plastic containers, buttress thread DIN 6063-1, 30-deg
https://www.gewinde-normen.de/en/KS-KT-thread.html KT 10 (x2) for plastic containers, trapezoidal thread DIN 6063-2 KT 12 (x2) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 14 (x2.5) for plastic containers, trapezoidal thread DIN 6063-2 KT 16 (x2.5) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 18 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 20 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 22 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 24 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 25 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 26 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 28 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 30 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 32 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 36 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 40 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KT 45 (x4) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KT 50 (x4) for plastic containers, trapezoidal thread DIN 6063-2 KS 10 (x2) for plastic containers, buttress thread DIN 6063-1, 40-deg KT 10 (x2) for plastic containers, trapezoidal thread DIN 6063-2 KS 12 (x2) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KT 12 (x2) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 14 (x2.5) for plastic containers, buttress thread DIN 6063-1, 40-deg KT 14 (x2.5) for plastic containers, trapezoidal thread DIN 6063-2 KS 16 (x2.5) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KT 16 (x2.5) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 18 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg KT 18 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 20 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg; less used dimension KT 20 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 22 (x3) for plastic containers, buttress thread DIN 6063-1, 40-deg KT 22 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 24 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KT 24 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 25 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KT 25 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 26 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KT 26 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 28 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KT 28 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 30 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KT 30 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 32 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KT 32 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 36 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KT 36 (x3) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 40 (x3) for plastic containers, buttress thread DIN 6063-1, 30-deg KT 40 (x3) for plastic containers, trapezoidal thread DIN 6063-2 KS 45 (x4) for plastic containers, buttress thread DIN 6063-1, 30-deg; less used dimension KT 45 (x4) for plastic containers, trapezoidal thread DIN 6063-2; less used dimension KS 50 (x4) for plastic containers, buttress thread DIN 6063-1, 30-deg KT 50 (x4) for plastic containers, trapezoidal thread DIN 6063-2 KS 60 (x6) for plastic containers, buttress thread DIN 6063-1, 30-deg
1/4-16 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 5/16-14 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 3/8-12 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 7/16-12 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1/2-10 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 5/8-8 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 3/4-6 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 7/8-6 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1"-5 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1.1/8-5 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1.1/4-5 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1.3/8-4 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1.1/2-4 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 1.3/4-4 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 2"-4 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 2.1/4-3 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 2.1/2-3 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 2.3/4-3 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 3"-2 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 3.1/2-2 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 4"-2 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 4.1/2-2 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg 5"-2 ACME for leadscrews, Acme trapezoidal thread, angle 29-deg
Tr10(x2) for leadscrews, metric trapezoidal thread, angle 30-deg Tr12(x3) for leadscrews, metric trapezoidal thread, angle 30-deg Tr14(x4) for leadscrews, metric trapezoidal thread, angle 30-deg Tr16(x4) for leadscrews, metric trapezoidal thread, angle 30-deg Tr24(x5) for leadscrews, metric trapezoidal thread, angle 30-deg Tr28(x5) for leadscrews, metric trapezoidal thread, angle 30-deg Tr32(x6) for leadscrews, metric trapezoidal thread, angle 30-deg Tr36(x6) for leadscrews, metric trapezoidal thread, angle 30-deg Tr40(x7) for leadscrews, metric trapezoidal thread, angle 30-deg Tr44(x7) for leadscrews, metric trapezoidal thread, angle 30-deg Tr48(x8) for leadscrews, metric trapezoidal thread, angle 30-deg Tr52(x8) for leadscrews, metric trapezoidal thread, angle 30-deg Tr60(x9) for leadscrews, metric trapezoidal thread, angle 30-deg Tr70(x10) for leadscrews, metric trapezoidal thread, angle 30-deg Tr80(x10) for leadscrews, metric trapezoidal thread, angle 30-deg Tr90(x12) for leadscrews, metric trapezoidal thread, angle 30-deg Tr100(x12) for leadscrews, metric trapezoidal thread, angle 30-deg
M5(x0.8) - some filament quick couplers M6x0.75 - UM3 nozzle M6(x1) - E3D nozzles, heater blocks, heatbreak hot end, E3Dv5 heatbreak top, usual filament quick-coupler M7(x1) - E3d v10 nozzles, E3D v6+ heatbreak top G1/8 - some filament quick couplers (9.6mm) M10(x1.5) - some filament quick couplers
M8x1, M8, M10x1, M10 - socket base, often uses hollow tube to lead the wires through; M10x1 most common, M8x1 little less common 3/8 IPS - 5/8-14 - socket base, US 1/2-26 - on lamps, hollow tubes for wires; on lamp hooks, lampholders; common in UK M13x1 - socket base, uncommon M16x1 - socket base, uncommon M25x1 - internal thread on some E14 socket throats, rare M28x2 - outside on E14 sockets, standard M33x1.5 - on "UNO" lampshades and sockets, standard M40x2.5 - outside on E27 sockets, standard hollow pipe: "lamp pipe" http://www.mylampparts.com/BVModules/Themes/MLP%20Responsive/images/faq/threads.jpg 6-32 approx.dia 1/8"; socket threads and switch plates 8-32 approx.dia 5/32"; lanter assemblies holder screws, cross bars, canopy lock ups 1/4-27 approx.dia 1/4"; shade risers, finals 1/8(-27) IPS 1/8-27 NPS, approx.dia 3/8; most common for table lamps and lamp sockets 1/4(-18) IPS 1/4-18 NPS, approx.dia 1/2; residential ceiling fixtures, floor lamps 3/8(-18) IPS 3/8-18 NPS, approx.dia 5/8; commercial ceiling fixtures, floor lamps https://grandbrass.zendesk.com/hc/en-us/articles/203607534-Thread-Size-Chart- #4-36 3/32 dia; socket thread #6-32 1/8 dia; socket thread, lantern assemblies #8-32 5/32 dia; lantern assemblies, drawer pulls #10-32 lantern assemblies, drawer pulls, where 8-32 not enough #10-24 lantern assemblies, common on hooksets 1/4-27 1/4 dia; lamp finals, shade risers 1/4-20 1/4 dia; heavy lockup thread; trophy products, drawer pulls, giftware assemblies 5/16-27 5/16 dia, hollow 1/8 IPS hollow; most common in lamp and lighting industry 1/4 IPS hollow; like 1/8 IPS where more strength is needed 3/8 IPS hollow; like 1/8 IPS, for very heavt duty fixture mounts https://grandbrass.zendesk.com/hc/en-us/articles/207350170-Lamp-Socket-Thread-Sizes ...also specifies
1/2 IPS hollow; M20x2 (on some lampshades) 3/8 IPS: This was the size of the outlets for gas lighting; the system of sizes used for the pipes that brought gas to gas lights was adopted for electric lights. In older ceiling fixtures (the outlet box is perfectly round instead of square) the light is attached to a 3/8 IP stud, just as a gas light was. Today an adapter, called a “hickey,” is used to get from the 3/8 IP stud to the fixture's 1/8 IP.
M8x1 M10x1 M12(x1.75) M16(x2) M20(x2.5) 3/8-16 1/8 IPS 1/4 IPS 3/8 IPS
AN3,4,5,6,8,10,12 M6x1 M8x1 M10x1 M10x1.25 M10x1.5 M12x1 M12x1.25 M12x1.5 M14x1.25 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M24x1.5 ORB-06 (o-ring boss, similar to AN3 but with oring instead of taper) ORB-08 ORB-10 1/8 BSP 1/4 BSP 1/2 BSP 3/4 BSP 3/8 BSP 1/8 NPT 1/4 NPT 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 25" (???) 1/8 NPT - common attachments for manometers and fuel pressure sensors
AN3 AN4 M10x1 M10x1.25 (less common) M12x1 M12x1.25 (less common?) 7/16-24
3/4-16UNF M18 x 1,5 M20 x 1,5 M22 x 1,5 3 / 4-16UNF pasuje na: Alfa Romeo, Audi, BMW (modely se šroubovatelným filtrem), Chrysler (kromě naftových motorů), DAF, Daimler Benz, Fiat (kromě diesel motorů), Ford (kromě Probe), Jeep, Lada, Lancia (kromě naftových motorů), Nissan (kromě naftových motorů), Opel corsa, Peugeot 205, Porsche 924 (motory 2.0 + turbo) Renault všechny modely do r.v. 06/84, Rover, Saab (kromě 2.5 V6,3.0 V6), Seat, Suzuki, Toyota (kromě naftových motorů), VW (kromě VR6), Volvo (kromě 440/480). M18 x 1,5 pasuje na: Citroen (některé modely) DEAWOO General Motors (všechny motory V6) Opel (některé modely) Saab (motory 2.5 V6, 3.0 V6) M20 x 1,5 pasuje na: Citroen (AX, BX, CX, XM, Visa GTi) Ford (Probe) Honda Hyundai Isuzu Jeep Cherokee Lada (Niva 1.9 Diesel) Mazda Mitsubishi Peugeot (některé modely) Porsche (944, 928, 968) Renaut všechny modely od r.v. 07/84 Subaru Volvo (440/480)
M8x1 M10x1 M12x1 M14x1 M16x1 M18x1 M22x1 M30x1.5 M40x1.5 7/16-16 UN 1/2-20 UNF
G1/4 female on sensor 1/4 NPT male on sensor 1/8 NPT male on sensor also G1/2 thermowells: 1/2 NPT G1/2
M8x1 M8 Picofast M12x1 M12 Eurofast 7/8-16 UN 7/8 Minifast M23x? M23 Multifast
#6-18 #7-16 #8-15 #10-12 #12-11 #20-9 #24-9
2-32 3-28 4-24 5-20 6-20 7-19 8-18 10-16 12-14 1/4-14 5/16-12 3/8-12 https://uk.misumi-ec.com/vona2/detail/221000547629/ type 1A 2-32 2.3-32 2.5-28 2.6-28 3-24 3.5-18 4-16 4.5-14 5-12 6-10 8-9 type B 1.4x0.45 1.6x0.5 1.7x0.5 2x0.6 2.5x0.9 https://uk.misumi-ec.com/vona2/detail/221005018425/?rid=rid3 type 0 type 2 type P M1.4x0.5 M1.6x0.64 M1.7x0.64 M2x0.79 M2.5x1.06 https://uk.misumi-ec.com/vona2/detail/221000547034/ https://uk.misumi-ec.com/vona2/detail/221000546976/ https://uk.misumi-ec.com/vona2/detail/221000547775/ type B0, B1 2-40 2.3-32 2.5-28 2.6-28 3-24 3.5-20 4-18 4.5-16 5-16 6-14 https://uk.misumi-ec.com/vona2/detail/221005017930/ P type 2-32 2.3-28 2.6-24 3-20 3.5-18 4-16 5-14 6-12 2-40 2x0.64; self-tapping screws type B 2-32 2x0.79; self-tapping screws type A; type P 2.3-32 2.3x0.79; self-tapping screws type A; type B 2.3-28 2.3x0.91; self-tapping screws type P 2.5-28 2.5x0.91; self-tapping screws type A; type B 2.6-28 2.6x0.91; self-tapping screws type A; type B 2.6-24 2.6x1.06; self-tapping screws type P 3-24 3x1.06; self-tapping screws type A, type B 3-20 3x1.27; self-tapping screws type P 3.5-20 3.5x1.27; self-tapping screws type B 3.5-18 3.5x1.41; self-tapping screws type A; type P 4-18 4x1.41; self-tapping screws type B 4-16 4x1.59; self-tapping screws type A; type P 4.5-16 4.5x1.59; self-tapping screws type B 4.5-14 4.5x1.81; self-tapping screws type A 5-16 5x1.59; self-tapping screws type B 5-14 5x1.81; self-tapping screws type P 5-12 5x2.12; self-tapping screws type A 6-14 6x1.81; self-tapping screws type B 6-12 6x2.12; self-tapping screws type P 6-10 6x2.54; self-tapping screws type A 8-9 8x2.82; self-tapping screws type A http://uploads.cycleapp.com/gusizl3xp/file.pdf 1.8x0.8 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 2.2x1 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 2.5x1.4 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 3x1.5 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 3.5x1.65 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 4x1.75 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 5x2.3 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 6x2.5 thread-rolling screws, Plas-Fix, for plastic, 45deg thread 2-28 2x0.91; thread-rolling screws, Plas-Fix, for plastic, 60deg thread 4-20 4x1.27; thread-rolling screws, Plas-Fix, for plastic, 60deg thread 6-19 6x1.34; thread-rolling screws, Plas-Fix, for plastic, 60deg thread 8-16 8x1.59; thread-rolling screws, Plas-Fix, for plastic, 60deg thread 10-14 10x1.81; thread-rolling screws, Plas-Fix, for plastic, 60deg thread 2.2x0.98 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 2.5x1.12 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 3x1.34 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 3.5x1.57 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 4x1.79 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 5x2.24 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 6x2.69 thread-forming screws, Plas-Tech 30, for plastic, 30deg thread 3x1.2 thread-forming screws, Polymate, for plastic, 40deg twin thread 3.5x1.4 thread-forming screws, Polymate, for plastic, 40deg twin thread 4x1.6 thread-forming screws, Polymate, for plastic, 40deg twin thread 5x2 thread-forming screws, Polymate, for plastic, 40deg twin thread 6x2.4 thread-forming screws, Polymate, for plastic, 40deg twin thread #5-20 thread-forming screws, high-low, for plastic, twin thread #6-19 thread-forming screws, high-low, for plastic, twin thread #8-18 thread-forming screws, high-low, for plastic, twin thread #10-16 thread-forming screws, high-low, for plastic, twin thread #11-16 thread-forming screws, high-low, for plastic, twin thread
https://www.smptthailand.com/Flat_rolling_Dies/57428184619192b8de7ae0bb square/hex lagscrews 10-11 1/4-10 5/16-9 3/8-7 7/16-7 1/2-6 5/8-5 3/4-4.5 wood screw m/m 1.6x0.8 1.8x0.9 2.1x1.0 2.4x1.1 2.7x1.2 3.1x1.3 3.5x1.4 3.8x1.6 4.1x1.8 4.5x2 4.8x2.1 5.1x2.2 5.5x2.4 5.8x2.6 6.2x2.7 6.8x3.1 7.5x3.3 8x3.3 9.5x3.8 wood screw DIN 1.4x0.6 1.6x0.7 1.7x0.8 2x0.9 2.4x1 2.7x1.2 3x1.35 3.5x1.6 4x1.8 4.5x2 5x2.2 5.5x2.4 6x2.6 7x3.2 8x3.5 9x4 10x4.5 12x5 16x6 wood screw asa 9-14 10-13 12-11 14-10 16-9 18-8 20-8 24-7 selftapping DIN 7970 M2.2x0.79 M2.9x1.06 3.5x1.27 3.9x1.34 4.2x1.41 4.8x1.59 5.5x1.81 6.3x1.81 8x2.12 selftapping W.T. type A 3/32-32 1/8-24 5/32-16 3/16-12 1/4-10 5/16-9 3/8-7 1/2-6 thread-rolling http://www.uturnfasteners.com/commercial-fasteners/screws/thread-rolling-screws/ 0-40 thread-rolling screws, Plastite alternative, 48deg 2-lead 2-56 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 2-28 thread-rolling screws, Plastite style, 48deg 2-lead 3-48 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals, uncommon 3-24 thread-rolling screws, Plastite style, 48deg 2-lead 4-40 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 4-20 thread-rolling screws, Plastite style, 48deg 2-lead 5-40 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals, uncommon diameter 5-20 thread-rolling screws, Plastite style, 48deg 2-lead, uncommon diameter 6-32 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 6-19 thread-rolling screws, Plastite style, 48deg 2-lead 7-18 thread-rolling screws, Plastite style, 48deg 2-lead, rare 8-32 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 8-16 thread-rolling screws, Plastite style, 48deg 2-lead 10-32 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 10-24 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 10-14 thread-rolling screws, Plastite style, 48deg 2-lead 12-24 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 12-11 thread-rolling screws, Plastite style, 48deg 2-lead 1/4-20 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 1/4-10 thread-rolling screws, Plastite style, 48deg 2-lead 5/16-18 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 5/16-9 thread-rolling screws, Plastite style, uncommon 3/8-16 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals 1/2-13 thread-rolling screws, Taptite style, machine thread; for drilled, punched or corred holes in ductile and punch extruded metals M1.6x0.67 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M2-0x89 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M2.2x0.98 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M2.2x1.0 thread-rolling screws, PLAS FIX 45 style, 45deg M2.5x1.4 thread-rolling screws, PLAS FIX 45 style, 45deg M2.5x1.12 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M3x1.5 thread-rolling screws, PLAS FIX 45 style, 45deg M3x1.34 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M3.5x1.57 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M3.5x1.65 thread-rolling screws, PLAS FIX 45 style, 45deg M4x1.75 thread-rolling screws, PLAS FIX 45 style, 45deg M4x1.79 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M5x2.3 thread-rolling screws, PLAS FIX 45 style, 45deg M5x2.24 thread-rolling screws, EJOT PT style, for thermoplastics, 30deg M6x2.5 thread-rolling screws, PLAS FIX 45 style, 45deg Tapcon masonry screws, for concrete, hi-lo thread 3/16-11 1/4-14, hi-lo 3/16-16, hi-lo LD, large-diameter Tapcon 3/8 1/2 5/8 3/4 1/4-4.5 wedge concrete anchor 1/4-8 wedge concrete anchor 3/8-3 wedge concrete anchor 1/2-2.5 wedge concrete anchor DRYWALL, DUROCK AND METAL PARTITION SCREWS https://www.reliablefasteners.com/ca/en/category/screws-and-fasteners/screws/drywall-durock-and-metal-partition-screws/1057485?imgMode=t&sort=&nbPerPage=48 ; #6-20 metal bulkhead screws, self-tapping #6-20 drywall screws, fine thread #6-18 drywall screws, fine thread #6-18 metal screws, self-tapping #6-15, #7-15, #8-15 drywall screws, fine thread #6-9 drywall screws, coarse thread #7-9 drywall screws, coarse thread #8-18 K-Lath (stucco) screw, self-tapping #8-18 cement panel screw, fine thread #8-15 K-Lath (stucco) screw, self-tapping #8-15 cement panel screw, fine thread #8-10 drywall screws, large thread #8-8 drywall screws, coarse thread #10-9 laminating screw, coarse thread ...unsorted, todo: look up these gauge numbers
#9-14 wood screws, ASA #14-10 wood screws, ASA #16-9 wood screws, ASA #18-8 wood screws, ASA #20-8 wood screws, ASA #24-7 wood screws, ASA
M1 on nosepads M1.2 common-ish (second most common?); on internal-thread screws (1.6mm outer dia); also some Ray-Ban 1.2x? selftapping M1.3x? uncommon M1.4 most common; hinges, some eyewires; also on internal-thread screws (1.8mm outer dia) 1.5x? uncommon M1.6 some hinges, some eyewires 1.8x? uncommon M2 2.35x? spacers, external thread (M1.4 internal); screws into material 2.85x? spacers, external thread (M1.4 internal); screws into material 1.16x? Ray-Ban 1.37x? Ray-Ban 1.8x? second most common self-tapping? 2x? self-tapping for plastic/wood frames, hinges; most common? 2.2x? 2.5x? M1.35 generic watch back case screw https://www.tabcooptical.com/screws-sorted-by-thread-size/ 00-90 also 1.16mm; lens/rimless screw, eyewires, hinges (USA), nuts for nose studs 0-64 often used on traditional B&;L frames; thread size 0-64 thread is used primarily in Optical eyewear and Jewelry M0.8 smallest nosepad screws M1 nosepad screws, standard, 1.4mm-dia head M1.1 nosepad screws 1.16x? rimless screw (SA112), eyewire; Ray-Ban nose pads and trim screws; Ray-Ban, B&;L 1.27-90(?) USA, typical hinge screw, eyewire, oversized 00-90, 00-90+, or 0.05-90; Ray-Ban hinge screw M1.2 eyewires, softwing nosepads, nuts; common on rimless; 2mm head and 4.7/6.7/8.7mm length == typical "eyewire screw" for smaller frames M1.3 hinges, eyewires, uncommon M1.4 hinges (most common), eyewires, nosepads, front/bridge, nuts; 9mm long for large frames; 2mm head and 3/3.5/4/5mm length == typical "eyewire screw" for smaller frames M1.5 hinges, eyewires, nuts; uncommon M1.6 some hinges (oversize), eyewires, uncommon M1.7 some hinges taps for repairs: M1.2, M1.3, M1.4, M1.5, M1.6 M0.9 watch winding stem/crown M1.2 watch winding stem/crown also M0.8, M1, M1.1 M1.2,M1.4,M1.6,M2 - Casio watch case screws M1,M1.2,M1.4 - watch case generic screws M1.3 - rarely used 0.9..1.4mm (by 0.1mm) - generics clock screws: M1 M1.2 M1.4 0.5mm, 0.6mm, 0.7mm, 0.8mm, 0.9mm, 1mm, 1.1mm, 1.2mm 0.55mm, 0.6mm, 0.65mm, 0.8mm, 0.9mm, 1mm watch pallet cock screw 0.6/0.8/0.9/1.1/1.3/1.4 watch pillar screws 0.6/0.7/0.8/0.9/1/1.1/1.2/1.3/1.4
4-40 15/25A 6-32 15/30A 8-32 15A 10-32 15/30A M1.6 2.54mm/0.1" pitch, 6A M2 7mm pitch (each other in 3.5mm), 10A/6A; 3.5mm pitch, 3.81mm/0.15" pitch, 13.5A/10A M2.5 15..130A; 5mm pitch, 5.08mm pitch, 8A M2.6 5mm pitch, 5.08mm pitch, 18A M3 15..130A; 10.16/0.4" pitch, 14A/20A; 10mm pitch, 24A; 9.53/0.375" pitch, 30A/5A; 8mm pitch, 20A; 7.62mm pitch, 18A/15A/10A; 7.5mm/20A; 6.35mm/0.25", 20/30A; 5mm pitch, 5.08mm/0.2" pitch, 10/15A; 4.5mm, 10A; 3.85mm, 12A M3.5 8mm pitch, 30A; 7.62mm/0.3" pitch, 30A; 6.35mm/0.25", 30A M4 15..180A; 12.7mm/0.5" pitch, 65A; 10.16/0.4" pitch, 60A M4.5 12.7mm/0.5" pitch, 65A M5 30..180A; 15mm pitch, 85A/115A/130A M6 160/250A; 17.48mm pitch, 160A M8 240/350A; 20mm pitch, 200A M10 320/350A https://www.wurth.ca/media/en/documents/catalogue/sections/fasteners.pdf
3/8 UNC 7/16 UNC 1/2 UNC 5/8 UNC standard body bolts 5/16-18 Ford, GM, 3/8-16 GM 1/4-20 Chrysler standard carriage bolts 1/4-20 5/16-18 3/8-16 7/16-14 1/2-13 5/8-11 standard elevator bolts 1/4-20 5/16-18 3/8-16 bottom rail bolt, buttonhead Torx 3/8-16 locking exhaust nuts, copper-coated, to 400'C M8x1 unusual M8x1.25 M10x1.25 M10x1.5 standard floorboard 1/4 UNC 5/16 UNC Tek Screws self-drilling ASD, BSD - coarse pitch CSD - matches UNC pitch
https://www.fastenerdata.co.uk/products/inserts/thread/metric-coarse-thread-insert-steel-din7965.html 6x2 M3 threaded insert, DIN 7965; 60deg, lesser dia 4.5mm 8x2.5 M4 threaded insert, DIN 7965; 60deg, lesser dia 5.5mm 10x3.5 M5 threaded insert, DIN 7965; 60deg, lesser dia 7.5mm 12x4 M6 threaded insert, DIN 7965; 60deg, lesser dia 9.5mm 16x5 M8 threaded insert, DIN 7965; 60deg, lesser dia 12.5mm 18.5x5 M10 threaded insert, DIN 7965; 60deg, lesser dia 15mm 22x5 M12 threaded insert, DIN 7965; 60deg, lesser dia 18mm 25x5 M16 threaded insert, DIN 7965; 60deg, lesser dia 20.5mm 29x5 M20 threaded insert, DIN 7965; 60deg, lesser dia 24mm
60deg V usual off the shelf 90deg V traditional, stronger (use declined in 19th century) https://www.lakeerietoolworks.com/collections/wooden-vise-screw-kits/products/la-forge-royale-miter-jack-hard-maple-screw-and-nut 90 degree (flatter) threads are less likely to chip on smaller threaded vises and are the type that we use on our Moxon screws as well. 60 degree threads (steeper) work better for larger screws with lower turns per inch (bigger threads) as they have more surface area for the screw and nut to engage. Popular Mechanics, 1944 https://books.google.cz/books?id=I98DAAAAMBAJ&pg=RA1-PA126&lpg=RA1-PA126&dq=wooden+thread+dimensions&source=bl&ots=3WkHh6IMP6&sig=ACfU3U3hnWeVtdHhCZbVGw2NJ_JVL7Sa9Q&hl=en&sa=X&ved=2ahUKEwjVz5iP9bLoAhUGfMAKHb1yDuo4ChDoATACegQICRAB#v=onepage&q=wooden%20thread%20dimensions&f=false ; 3/8-10,12,16* 1/2-8,10,12*,13* 5/8-8,10,11*,12* 3/4-6,8,18*,12* 7/8-6,8,9*,12* 1-4,6,8*,12* 1.1/8-4,7*,8 1.1/4-4,7*,8 1.1/2-4,6*,8 1.3/4-4,5*,8 2-4,4.5*,8 https://www.amazon.com/Beall-Basic-Size-Wood-Threading/dp/B008CQE0CI 1/2-8 3/4-6 1-6 http://www.bealltool.com/products/threading/threader.php 1/2-8 5/8-7 3/4-6 1-6 1.1/4-5 1.1/2-5 large wooden vise: https://forestryforum.com/board/index.php?topic=49489.0 2.1/4-2 https://www.fine-tools.com/gewind.html 3/8-9 10mm 1/2-8 13mm 5/8-7 16mm 3/4-6 19mm 7/8-5.5 22mm 1"-5 25mm 1.1/8-4.5 28mm 1.1/4-4 32mm 1.1/2-3.5 38mm 1.3/4-3 44mm 2-2.5 50mm 2.1/2-2 62mm https://www.axminster.co.uk/axminster-wood-thread-cutting-kit-ax21303 1/2-8 3/4-6 1-6 1.1/2-6 carbatex 1/2-8 3/4-6 1-6 1.1/4-6 1.1/2-6 Peugeot Freres, ancient 2-3.5
https://www.fass.it/en/manici-fissi-2/ diameters: 21,22,25mm threads: Greek less common?, trapezoid, moderate pitch, straight Italian half-round, tapered, large pitch, very common?, "euro"; maybe 90deg v as well? German V, very tapered, small pitch French V, very slight taper if any, small pitch USA 3/4-5 ACME (half-round); also long USA, same dia with hole (?) https://www.fimm.cloud/site/en/products-en/metal-handles/threads also: Mexican half-round, very large pitch, very small taper Australian trapezoid, sligthly smaller pitch than greek, very slight taper universal V (slightly asymmetric), small pitch, tapered Italian Pro (Italian with hole) DIN 68345:1968 DE, :2016 - thread specification https://webstore.ansi.org/cover-pages/small/DIN/1303760.jpg bottom dia 20.5mm taper 7deg40' male, 8deg female top dia 24mm pitch 2.5mm profile triangular, 0.2mm radius rounded tip, 1mm deep - large flat roots (same profile for female, inverted, also large flat roots) female thread socket 10mm deep 24x2.5 taper broomstick handle, German, DIN 68345; 24mm top dia, 20.5mm bottom dia, 2.5mm pitch, 7deg40' taper male, 8deg taper female, 60deg V profile 1mm deep, 0.2mm crest radius euro thread: 22mm? other US: 1.080"-4, ACME "Vikan thread" https://patents.google.com/patent/EP1252978A1/en French thread, Italian thread (actually southern Europe, with Spain and Portugal), German thread (actually northern European country), American thread D = external diameter of the thread (mm), d = diameter at the bottom of the thread (mm), h = height (mm), p = screw pitch (mm). For D and d, the two extreme values for conical threads are mentioned below. France : Germany: - D = from 23.7 to 22.7 (taper), - D = 24.7 to 22 (taper), - d = 22.7 to 21.7 (taper), - d = 22.7 to 20 (taper), - h = 24 (variable), - h = 20 (variable), - p = 2. - p = 2 Italy: USA: - D = 21 to 19 (taper), - D = 18.3, - d = 19 to 17 (taper), - d = 14.7, - h = 22 (variable), - h = 21, - p = 4. - p = 4 France Germany Italy USA USA top external dia 22.7 23.7 24.7 22.0 19.0 21.0 18.3 3/4" bottom external dia 21.7 22.7 22.7 20.0 17.0 19.0 14.7 3/4" height ~ 24 ~ 20 ~ 22 ~ 21? pitch 2 2 4 4 5.08 profile V V halfround ? ACME? taper 1:24 1:10 1:11 ~ 1:5 1 standard broomstick diameter about 23 mm 23.7x2 broomstick handles, standard France; tapered, top dia 22.7..23.7mm, bottom dia 21.7..22.7mm, pitch 2mm, length about 24mm (varies) 24.7x2 broomstick handles, standard Germany/northern Europe; tapered, top dia 22.0..24.7mm, bottom dia 20.0..22.7mm, pitch 2mm, length about 20mm (varies) 24.7x2 broomstick handles, standard Italy/southern Europe/Spain/Portugal; tapered, top dia 19..21mm, bottom dia 17..19mm, pitch 4mm, length about 22mm (varies) For France, Germany and Italy, the values of D1 and d mentioned are the values at each end. For Germany, the dimensional characteristics are appreciably identical to those of France, but with a greater taper. For the USA, the dimensional characteristics are appreciably identical to those of Italy, but with a greater taper. toilet brush handle: M12, male on handle also 9.5mm thread, trapezoid/acme? relaxdays-only? also M6 M12, also wire chimney brushes M12, espresso machines, filter handles, also M10 5/16-18 pellet stove brush 8-32 gun chamber/bore brushes
@ Rd10(x3) round/knuckle thread, DIN 20400 @ Rd12(x3) round/knuckle thread, DIN 20400 @ Rd14(x3) round/knuckle thread, DIN 20400 @ Rd16(x4) round/knuckle thread, DIN 20400 @ Rd18(x4) round/knuckle thread, DIN 20400 @ Rd20(x4) round/knuckle thread, DIN 20400 @ Rd22(x4) round/knuckle thread, DIN 20400 @ Rd25(x4) round/knuckle thread, DIN 20400 @ Rd28(x4) round/knuckle thread, DIN 20400 @ Rd32(x4) round/knuckle thread, DIN 20400 @ Rd36(x5) round/knuckle thread, DIN 20400 @ Rd40(x5) round/knuckle thread, DIN 20400 @ Rd42(x5) round/knuckle thread, DIN 20400 @ Rd45(x5) round/knuckle thread, DIN 20400 @ Rd48(x5) round/knuckle thread, DIN 20400 @ Rd50(x5) round/knuckle thread, DIN 20400 @ Rd53(x5) round/knuckle thread, DIN 20400 @ Rd56(x5) round/knuckle thread, DIN 20400 @ Rd60(x6) round/knuckle thread, DIN 20400 @ Rd63(x6) round/knuckle thread, DIN 20400 @ Rd67(x6) round/knuckle thread, DIN 20400 @ Rd70(x6) round/knuckle thread, DIN 20400 @ Rd75(x6) round/knuckle thread, DIN 20400 @ Rd80(x6) round/knuckle thread, DIN 20400 @ Rd85(x6) round/knuckle thread, DIN 20400 @ Rd90(x8) round/knuckle thread, DIN 20400 @ Rd95(x8) round/knuckle thread, DIN 20400 @ Rd100(x8) round/knuckle thread, DIN 20400 @ Rd106(x8) round/knuckle thread, DIN 20400 @ Rd112(x8) round/knuckle thread, DIN 20400 @ Rd118(x8) round/knuckle thread, DIN 20400 @ Rd125(x8) round/knuckle thread, DIN 20400 @ Rd133(x10) round/knuckle thread, DIN 20400 @ Rd140(x10) round/knuckle thread, DIN 20400 @ Rd150(x10) round/knuckle thread, DIN 20400 @ Rd160(x10) round/knuckle thread, DIN 20400 @ Rd170(x10) round/knuckle thread, DIN 20400 @ Rd180(x12) round/knuckle thread, DIN 20400 @ Rd190(x12) round/knuckle thread, DIN 20400 @ Rd200(x12) round/knuckle thread, DIN 20400 @ Rd212(x12) round/knuckle thread, DIN 20400 @ Rd224(x12) round/knuckle thread, DIN 20400 @ Rd236(x16) round/knuckle thread, DIN 20400 @ Rd250(x16) round/knuckle thread, DIN 20400 @ Rd265(x16) round/knuckle thread, DIN 20400 @ Rd280(x16) round/knuckle thread, DIN 20400 @ Rd300(x16) round/knuckle thread, DIN 20400 buttress thread, coarse, DIN 513 @ S10x2 buttress thread, coarse, DIN 513; flank angle 33 deg @ S12x3 buttress thread, coarse, DIN 513; flank angle 33 deg @ S14x3 buttress thread, coarse, DIN 513; flank angle 33 deg @ S16x4 buttress thread, coarse, DIN 513; flank angle 33 deg @ S18x4 buttress thread, coarse, DIN 513; flank angle 33 deg @ S20x4 buttress thread, coarse, DIN 513; flank angle 33 deg @ S22x5 buttress thread, coarse, DIN 513; flank angle 33 deg @ S24x5 buttress thread, coarse, DIN 513; flank angle 33 deg @ S26x5 buttress thread, coarse, DIN 513; flank angle 33 deg @ S28x5 buttress thread, coarse, DIN 513; flank angle 33 deg @ S30x6 buttress thread, coarse, DIN 513; flank angle 33 deg @ S32x6 buttress thread, coarse, DIN 513; flank angle 33 deg @ S34x6 buttress thread, coarse, DIN 513; flank angle 33 deg @ S36x6 buttress thread, coarse, DIN 513; flank angle 33 deg @ S38x7 buttress thread, coarse, DIN 513; flank angle 33 deg @ S40x7 buttress thread, coarse, DIN 513; flank angle 33 deg @ S42x7 buttress thread, coarse, DIN 513; flank angle 33 deg @ S44x7 buttress thread, coarse, DIN 513; flank angle 33 deg @ S46x8 buttress thread, coarse, DIN 513; flank angle 33 deg @ S48x8 buttress thread, coarse, DIN 513; flank angle 33 deg @ S50x8 buttress thread, coarse, DIN 513; flank angle 33 deg @ S52x8 buttress thread, coarse, DIN 513; flank angle 33 deg @ S55x9 buttress thread, coarse, DIN 513; flank angle 33 deg @ S60x9 buttress thread, coarse, DIN 513; flank angle 33 deg @ S65x10 buttress thread, coarse, DIN 513; flank angle 33 deg @ S70x10 buttress thread, coarse, DIN 513; flank angle 33 deg @ S75x10 buttress thread, coarse, DIN 513; flank angle 33 deg @ S80x10 buttress thread, coarse, DIN 513; flank angle 33 deg @ S85x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S90x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S95x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S100x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S105x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S110x12 buttress thread, coarse, DIN 513; flank angle 33 deg @ S115x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S120x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S125x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S130x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S135x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S140x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S145x14 buttress thread, coarse, DIN 513; flank angle 33 deg @ S150x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S155x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S160x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S165x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S170x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S175x16 buttress thread, coarse, DIN 513; flank angle 33 deg @ S180x18 buttress thread, coarse, DIN 513; flank angle 33 deg @ S185x18 buttress thread, coarse, DIN 513; flank angle 33 deg @ S190x18 buttress thread, coarse, DIN 513; flank angle 33 deg @ S195x18 buttress thread, coarse, DIN 513; flank angle 33 deg @ S200x18 buttress thread, coarse, DIN 513; flank angle 33 deg @ S210x20 buttress thread, coarse, DIN 513; flank angle 33 deg @ S220x20 buttress thread, coarse, DIN 513; flank angle 33 deg @ S230x20 buttress thread, coarse, DIN 513; flank angle 33 deg @ S240x22 buttress thread, coarse, DIN 513; flank angle 33 deg @ S250x22 buttress thread, coarse, DIN 513; flank angle 33 deg @ S260x22 buttress thread, coarse, DIN 513; flank angle 33 deg @ S270x24 buttress thread, coarse, DIN 513; flank angle 33 deg @ S280x24 buttress thread, coarse, DIN 513; flank angle 33 deg @ S290x24 buttress thread, coarse, DIN 513; flank angle 33 deg @ S300x24 buttress thread, coarse, DIN 513; flank angle 33 deg buttress thread, fine, DIN 514 @ S12x2 buttress thread, fine, DIN 514; flank angle 33 deg @ S14x2 buttress thread, fine, DIN 514; flank angle 33 deg @ S16x2 buttress thread, fine, DIN 514; flank angle 33 deg @ S18x2 buttress thread, fine, DIN 514; flank angle 33 deg @ S20x2 buttress thread, fine, DIN 514; flank angle 33 deg @ S22x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S24x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S26x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S28x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S30x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S32x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S34x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S36x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S38x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S40x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S42x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S44x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S46x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S48x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S50x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S52x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S55x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S60x3 buttress thread, fine, DIN 514; flank angle 33 deg @ S65x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S70x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S75x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S80x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S85x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S90x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S95x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S100x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S105x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S110x4 buttress thread, fine, DIN 514; flank angle 33 deg @ S115x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S120x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S125x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S130x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S135x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S140x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S145x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S150x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S155x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S160x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S165x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S170x6 buttress thread, fine, DIN 514; flank angle 33 deg @ S175x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S180x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S185x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S190x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S195x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S200x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S210x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S220x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S230x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S240x8 buttress thread, fine, DIN 514; flank angle 33 deg @ S250x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S260x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S270x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S280x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S290x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S300x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S320x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S340x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S360x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S380x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S400x12 buttress thread, fine, DIN 514; flank angle 33 deg @ S420x18 buttress thread, fine, DIN 514; flank angle 33 deg @ S440x18 buttress thread, fine, DIN 514; flank angle 33 deg @ S460x18 buttress thread, fine, DIN 514; flank angle 33 deg @ S480x18 buttress thread, fine, DIN 514; flank angle 33 deg @ S500x18 buttress thread, fine, DIN 514; flank angle 33 deg @ S520x24 buttress thread, fine, DIN 514; flank angle 33 deg @ S540x24 buttress thread, fine, DIN 514; flank angle 33 deg @ S560x24 buttress thread, fine, DIN 514; flank angle 33 deg @ S580x24 buttress thread, fine, DIN 514; flank angle 33 deg @ S600x24 buttress thread, fine, DIN 514; flank angle 33 deg @ S100x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S106x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S112x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S118x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S125x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S132x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S140x5 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S150x6 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S160x6 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S170x6 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S180x6 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S190x6 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S200x8 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S212x8 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S224x8 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S236x8 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S250x8 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S265x10 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S280x10 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S300x10 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S315x10 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S335x12 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S355x12 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S375x12 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S400x16 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S425x16 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S450x16 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S475x16 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S500x16 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S530x20 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S560x20 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S600x20 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S630x20 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S670x24 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S710x24 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S750x24 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S800x32 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S850x32 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S900x32 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S950x32 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S1000x32 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S1060x40 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S1120x40 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S1180x40 buttress thread, 45 deg, DIN 2781; on hydraulic presses @ S1250x40 buttress thread, 45 deg, DIN 2781; on hydraulic presses bicycle screw, 60deg @ Fg2(-56) 2.096x0.454, bicycle screw thread, 60 deg, DIN 79012 @ Fg2.3(-56) 2.299x0.454, bicycle screw thread, 60 deg, DIN 79012 @ Fg2.6(-56) 2.604x0.454, bicycle screw thread, 60 deg, DIN 79012 @ Fg6.35(-26) 6.350x0.977, bicycle screw thread, 60 deg, DIN 79012 @ Fg7.9(-26) 7.938x0.977, bicycle screw thread, 60 deg, DIN 79012 @ Fg9.5(-26) 9.525x0.977, bicycle screw thread, 60 deg, DIN 79012 @ Fg14.3(-20) 14.288x1.27, bicycle screw thread, 60 deg, DIN 79012 @ Fg25.4(-24) 25.400x1.058, bicycle screw thread, 60 deg, DIN 79012 @ Fg32.8(-24) 32.766x1.058, bicycle screw thread, 60 deg, DIN 79012 @ Fg34.8(-24) 34.798x1.058, bicycle screw thread, 60 deg, DIN 79012 dairy thread @ DN10(-8) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN15(-8) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN20(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN25(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN32(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN40(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN50(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN65(-6) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN80(-4) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN90(-4) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN100(-4) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN125(-4) "dairy thread", knuckle/round thread, DIN 11851, common in food industry @ DN150(-4) "dairy thread", knuckle/round thread, DIN 11851, common in food industry Bodmer thread https://www.gewinde-normen.de/en/bodmer-thread.html H 3x0.625 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 3.5x0.625 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 4x0.715 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 4.5x0.715 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 5x0.834 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 5.5x0.834 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 6x0.834 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 7x1 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 8x1 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 9x1.25 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 10x1.25 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 11x1.25 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 12x1.471 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 13x1.471 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 14x1.724 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 15x1.724 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 16x2 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 18x2 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 20x2.5 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 22x2.5 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 24x2.78 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 26x2.78 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 28x3.125 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 30x3.125 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 32x3.571 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 34x3.571 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 38x4.167 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 42x4.167 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 46x5 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments H 50x5 Bodmer Thread, historical, 50 deg; for mechanical and optical instruments French thread H 6x1 S.F. No.0, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 8x1 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 10x1.5 S.F. No.1, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 12x1.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 14x2 S.F. No.2, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 16x2 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 18x2.5 S.F. No.3, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 20x2.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 22x2.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 24x3 S.F. No.4, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 26x3 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 28x3 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 30x3.5 S.F. No.5, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 32x3.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 34x3.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 36x4 S.F. No.6, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 38x4 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 40x4 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 42x4.5 S.F. No.7, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 44x4.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 46x4.5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 48x5 S.F. No.8, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 50x5 French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 56x5.5 S.F. No.9, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 64x6 S.F. No.10, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 72x6.5 S.F. No.11, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 80x7 S.F. No.12, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 88x7.5 S.F. No.13, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 96x8 S.F. No.14, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 106x8.5 S.F. No.15, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 116x9 S.F. No.16, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 126x9.5 S.F. No.17, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 136x10 S.F. No.18, French thread, S.F., System Francais; 60deg; historical, before introduction of SI H 148x10.5 S.F. No.19, French thread, S.F., System Francais; 60deg; historical, before introduction of SI VDI Thread H 6x1 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 7x1.1 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 8x1.2 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 9x1.3 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 10x1.4 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 12x1.6 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 14x1.8 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 16x2 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 18x2.2 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 20x2.4 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 22x2.8 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 24x2.8 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 26x3.2 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 28x3.2 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 30x3.6 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 32x3.6 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 36x4 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 H 40x4.4 VDI thread, 53.8 deg, historical; standardized in Germany in 1888, replaced with SI thread in 1989 S.J. thread H 6x1 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 7x1 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 8x1.25 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 9x1.25 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 10x1.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 11x1.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 12x1.75 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 14x2 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 16x2 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 18x2.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 20x2.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 22x2.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 24x3 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 27x3 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 30x3.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 33x3.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 36x4 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 39x4 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 42x4.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 45x4.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 48x5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 52x5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 56x5.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 60x5.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 64x6 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 68x6 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 72x6.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 76x6.5 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H 80x7 S.J. thread, 60 deg, historical; standardized in 1898, precursor of metric ISO thread H W14x1/12" Whitworth Fine Thread DIN 30284, 55deg, constant pitch, historical; used in locomotive construction until about 1975 H W15x1/12" Whitworth Fine Thread DIN 30284, 55deg, constant pitch, historical; used in locomotive construction until about 1975 H W17x1/12" Whitworth Fine Thread DIN 30284, 55deg, constant pitch, historical; used in locomotive construction until about 1975 H W18x1/12" Whitworth Fine Thread DIN 30284, 55deg, constant pitch, historical; used in locomotive construction until about 1975 H W20x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W23x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W23x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W26x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W26x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W28x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W30x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W30x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W32x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W33x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W33x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W34x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W34x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W36x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W36x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W37x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W37x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W39x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W40x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W40x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W42x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W42x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W43x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W43x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W46x1/12" Whitworth Fine Thread DIN LON 282, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W46x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W50x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W53x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W56x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W56x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W60x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W60x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W60x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W63x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W64x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W64x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W66x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W68x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W68x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W70x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W72x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W72x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W73x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W76x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W76x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W76x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W80x1/10" LON Whitworth Fine Thread DIN LON 286, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W80x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W80x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W84x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W84x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W89x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W89x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W94x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W94x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W99x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W99x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W104x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W104x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W109x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W109x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W114x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W114x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W119x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W119x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W124x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W124x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W129x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W129x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W134x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W134x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W139x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W139x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W144x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W144x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W149x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W149x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W154x1/6" LON Whitworth Fine Thread 2 DIN LON 287, 55 deg, constant pitch, historical; used in locomotive construction until about 1975 H W154x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W159x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W164x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W169x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W174x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W179x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W184x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W189x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W194x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W199x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W204x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W209x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W214x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W219x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W224x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W229x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W234x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W239x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W244x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W249x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W254x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W259x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W264x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W269x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W274x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W279x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W284x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W289x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W294x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W299x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W304x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W309x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W314x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W319x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W324x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W329x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W334x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W339x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W344x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W349x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W354x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W359x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W364x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W369x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W374x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W379x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W384x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W389x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W394x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W399x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W404x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W409x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W414x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W419x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W424x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W429x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W434x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W439x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W444x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W449x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W454x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W459x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W464x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W469x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W474x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W479x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W484x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W489x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W494x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W499x1/4" Whitworth Fine Thread 1 DIN 239, 55 deg, constant pitch, historical H W20x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W22x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W24x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W27x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W30x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W33x1/10" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W36x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W39x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W42x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W45x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W48x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W52x1/8" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W56x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W60x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W64x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W68x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W72x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W76x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W80x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W84x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W89x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W94x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W99x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W104x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W109x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W114x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W119x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W124x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W129x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W134x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W139x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W144x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W149x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W154x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W159x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W164x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W169x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W174x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W179x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W184x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical H W189x1/6" Whitworth Fine Thread 2 DIN 240, 55 deg, historical Ducommun Steinle thread H 3x0.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 4x0.75 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 5x0.75 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 6x1 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 7x1.25 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 8x1.25 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 9x1.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 10x1.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 12x1.75 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 15x2 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 18x2.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 20x2.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 23x3 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 25x3 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 28x3 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 30x3.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 32x3.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 35x4 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 38x4 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 40x4 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 45x4.5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 48x5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 50x5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 55x5 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 60x6 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 65x6 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 70x7 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 75x7 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments H 80x7 Ducommun Steinle thread, 60 deg, historical; established in 1873; for mechanical and optical instruments UNR - UN with controlled root radius 5/16-28 5/16-20 3/8-28 3/8-20 7/16-32 7/16-16 1/2-32 1/2-16 9/16-32 9/16-28 9/16-20 9/16-16 5/8-32 5/8-28 5/8-20 5/8-16 5/8-12 11/16-32 11/16-28 11/16-20 11/16-16 11/16-12 3/4-32 3/4-28 3/4-12 13/16-32 13/16-28 13/16-16 13/16-12 7/8-32 7/8-28 7/8-16 7/8-12 15/16-32 15/16-28 15/16-16 15/16-12 1-32 1-28 1-16 1.1/16-28 1.1/16-20 1.1/16-16 1.1/16-12 1.1/16-8 1.1/8-28 1.1/8-20 1.1/8-16 1.1/8-8 1.3/16-28,20,16,12,8 1.1/4-28,20,16,8 1.5/16-28,20,16,12,8 1.3/8-28,20,16,8 1.7/16-28,20,16,12,8,6 1.1/2-28,20,16,8 1.9/16-20,16,12,8,6 1.5/8-20.16.12.8.6 1.11/16-20,16,12,8,6 1.3/4-20,16,12,8,6 1.13/16-20,16,12,8,6 1.7/8-20,16,12,8,6 1.15/16-20,16,12,8,6 2-20,16,12,8,6 2.1/8-20,16,12,8,6 2.1/4-20,16,12,8,6 2.3/8-20,16,12,8,6 2.1/2-20,16,12,8,6 2.5/8-20,16,12,8,6 2.3/4-20,16,12,8,6 2.7/8-20,16,12,8,6 3-20,16,12,8,6 3.1/8-16,12,8,6 3.1/4-16,12,8,6 3.3/8-16,12,8,6 3.1/2-16,12,8,6 3.5/8-16,12,8,6 3.3/4-16,12,8,6 3.7/8-16,12,8,6 4-16,12,8,6 4.1/8-16,12,6 4.1/4-16,12,6,4 4.3/8-16,12,6 4.1/2-16,12,6,4 4.5/8-16,12,6 4.3/4-16,12,6,4 4.7/8-16,12,6 5-16,12,6,4 5.1/8-16,12 5.1/4-16,12,4 5.3/8-16,12 5.1/2-16,12,4 5.5/8-16,12 5.3/4-16,12,4 5.7/8-16,12 6-16,12,4 trapezoidal fine: L Tr8x1.5 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr9x1.5 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr10x1.5 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr11x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr12x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr14x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr16x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr18x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr20x2 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr22x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr24x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr26x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr28x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr30x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr32x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr34x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr36x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr38x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr40x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr42x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr44x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr46x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr48x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr50x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr52x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr55x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr60x3 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr65x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr70x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr75x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr80x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr85x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr90x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr95x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr100x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr105x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr110x4 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr115x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr120x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr125x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr130x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr135x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr140x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr145x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr150x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr155x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr160x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr165x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr170x6 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr175x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr180x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr185x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr190x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr195x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr200x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr210x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr220x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr230x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr240x8 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr250x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr260x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr270x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr280x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr290x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr300x12 trapezoidal fine, 30 deg, DIN 103; for leadscrews L Tr8x2 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr9x2 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr10x3 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr11x3 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr12x3 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr14x3 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr16x4 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr18x4 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr20x4 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr22x5 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr24x5 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr26x5 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr28x5 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr30x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr32x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr34x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr36x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr38x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr40x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr42x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr44x6 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr46x8 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr48x8 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr50x8 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr52x8 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr55x9 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr60x9 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr65x10 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr70x10 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr75x10 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr80x10 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr85x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr90x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr95x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr100x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr105x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr110x12 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr115x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr120x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr125x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr130x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr135x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr140x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr145x14 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr150x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr155x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr160x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr165x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr170x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr175x16 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr180x18 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr185x18 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr190x18 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr195x18 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr200x18 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr210x20 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr220x20 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr230x20 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr240x22 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr250x22 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr260x22 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr270x24 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr280x24 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr290x24 trapezoidal coarse, 30 deg, DIN 103; for leadscrews L Tr300x24 trapezoidal coarse, 30 deg, DIN 103; for leadscrews
https://www.ring-plug-thread-gages.com/PDChart/Locknut-thread-data.html others: https://www.ring-plug-thread-gages.com/ti-thread-data-charts.html https://www.rebell-tools.de/DE/gewinde.html https://www.rebell-tools.de/DE/normen.html UNJ, UNJF, UNJEF: http://bazistools.ru/assets/site/uploads/download/SAE/SAE%20AS8879B-2001.pdf
@ Glasg 74.5(x7.5) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few @ Glasg 84.5(x7.5) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few @ Glasg 99(x7.5) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few @ Glasg 123.5(x7.5) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few @ Glasg 158(x12) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few @ Glasg 188(x12) electric lighting fittings, glass lamp covers, DIN 40450; obsolete, still made by few
https://www.medin.cz/bone-screws https://www.iso.org/obp/ui/#iso:std:iso:5835:ed-1:v1:en @ HA 1.5 1.5x0.5, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 1.1mm; ISO 5835:1991 @ HA 2 2x0.6, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 1.3mm; ISO 5835:1991 @ HA 2.4 2.4x?, medical implants, bone screws, shallow thread, unusual dia; cortical bone screw; asym thread 35/3 deg rounded @ HA 2.7 2.7x1, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 1.9mm; ISO 5835:1991 @ HA 3.5 3.5x1.25, medical implants, bone screws, shallow thread; cortical bone screw, also cannulated; asym thread 35/3 deg rounded, minor dia 2.4mm; ISO 5835:1991 @ HA 4 4x1.5, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 2.9mm; ISO 5835:1991 @ HB 4 4x1.75, medical implants, bone screws, deep thread; cancellous bone screw; asym thread 25/5 deg rounded, minor dia 1.9mm; ISO 5835:1991 @ HA 4.5 4.5x1.75, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 3mm; ISO 5835:1991 @ HB 4.5 4.5x?, medical implants, bone screws, deep thread, unusual dia; navicular bone screw, also cannulated; asym thread 25/5 deg rounded @ HA 5 5x1.75, medical implants, bone screws, shallow thread; cortical bone screw; asym thread 35/3 deg rounded, minor dia 3.5mm; ISO 5835:1991 @ HB 6.5 6.5x2.75, medical implants, bone screws, deep thread; cancellous bone screw; asym thread 25/5 deg rounded, minor dia 3mm; ISO 5835:1991 @ HB 7 7x?, medical implants, bone screws, deep thread, unusual dia; cancellous bone screw, cannulated; asym thread 25/5 deg rounded cannulated: 2.7,3,3.5,4,4.5,6.5,7,7.5
https://www.gewinde-normen.de/hamann-patronen-gewinde.html https://forum.strojirenstvi.cz/viewtopic.php?t=29228 diameter usually 40mm (inner 24mm), length 40mm (Hamann machines), 31.2/20mm (Boley/Leinen machines) H 40-6.5 Hamann Patronengewinde No.1, pitch 3.907mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-40-8.75 Hamann Patronengewinde No.2, pitch 2.903mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors; pitch in mm bad in original source H 40-9.3/11 Hamann Patronengewinde No.3, pitch 2.739mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-13 Hamann Patronengewinde No.4, pitch 1.953mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-16.3/7 Hamann Patronengewinde No.5, pitch 1.546mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors; pitch in inch bad in original source H 40-20 Hamann Patronengewinde No.6, pitch 1.270mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-22 Hamann Patronengewinde No.7, pitch 1.154mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-26 Hamann Patronengewinde No.8, pitch 0.976mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-29.1/13 Hamann Patronengewinde No.9, pitch 0.873mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-36 Hamann Patronengewinde No.10, pitch 0.705mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-40 Hamann Patronengewinde No.11, pitch 0.635mm; on old Hamann lathes, 64 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-55 Hamann Patronengewinde No.12tf., pitch 0.461mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-55 Hamann Patronengewinde No.12fl., pitch 0.461mm; on old Hamann lathes, 76 deg; year 1850, historical; cartridge diameter may vary for other vendors H 40-88 Hamann Patronengewinde No.13, pitch 0.288mm; on old Hamann lathes, 50 deg; year 1850, historical; cartridge diameter may vary for other vendors
https://www.sizes.com/tools/thread_waltham.htm
http://www.mettex.co.uk/wp-content/uploads/2014/11/Fabory-Fasteners-Screw-Threads.pdf @ MFS 6x1 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 7x1 metric for interference fit in cast aluminum alloys, DIN 8141:1993; secondary size, avoid; oversized major dia @ MFS 8x1.25 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 9x1.25 metric for interference fit in cast aluminum alloys, DIN 8141:1993; secondary size, avoid; oversized major dia @ MFS 10x1.5 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 11x1.5 metric for interference fit in cast aluminum alloys, DIN 8141:1993; secondary size, avoid; oversized major dia @ MFS 12x1.75 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 14x2 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 16x2 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 18x2.5 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 20x2.5 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 22x2.5 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia @ MFS 24x3 metric for interference fit in cast aluminum alloys, DIN 8141:1993; oversized major dia
@ M5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M6 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M8x1 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M10x1 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M10x1.25 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M12x1 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M12x1.25 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M12x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M14x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M16x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M18x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M20x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M22x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M24x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M26x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M27x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M27x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M30x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M30x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M33x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M33x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M36x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M36x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M38x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M39x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M39x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M42x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M42x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M45x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M45x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M48x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M48x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M52x1.5 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M52x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M56x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples @ M60x2 keg metric pipe thread DIN 158, 1:16 taper on male, female straight (DIN 158-1) or taper (old DIN 158); sealing screws, connectors, lubrication nipples
GL10 12mm dia GL14 16mm dia GL18 20mm dia GL20 22mm dia GL22 25mm dia
https://www.kohinoor.cz/storage/3_1_EN_manual-en.pdf GL18 GL20 GL22; also dispensing closure DU2 GL28 roll-on applicators for cosmetics
speaker enclosure thread sizes: http://www.speakerspikes.net/threads.htm https://soundocity.com/what-bolt-thread-size-is-needed-to-mount-outriggers-to-your-speakers/ 1.3/8-18 usual mounting thread on tweeter speakers with 1" exit https://service.shure.com/s/article/sm58-ball-grill-thread-size-rk143g?language=en_US 1.25-28 UN usual thread for grilles for most ball-shaped dynamic microphones; eg. SM58 also for microphone capsules connection by 3 wiper/spring concentric contacts; ground (edge), power, signal (center) 5/16", 1/2" nonstandard vintage microphone mounts M8, M10, 3/8-16 for suspension of speaker cabinets Micro-Con-X connectors https://cz.mouser.com/datasheet/2/393/conxall_catalog-488.pdf 7/16-28 UNEF Micro-Con-X, 2..3 contacts 5/8-27 UNEF Mini-Con-X, 2..8 contacts 13/16-27 UNS Multi-Con-X, 2..9 contacts 1-20 UNEF Maxi-Con-X, 7,10,18..20 contacts 1.3/16-20 UN Mega-Con-X, 31 contacts 7/16-28 UNEF connectors, eg. circular Micro-Con-X Switchcraft connectors 5/8-27 UNEF connectors, eg. circular Mini-Con-X Switchcraft connectors 13/16-27 UNS connectors, eg. circular Multi-Con-X Switchcraft connectors 1-20 UNEF connectors, eg. circular Maxi-Con-X Switchcraft connectors 1.3/16-20 UN connectors, eg. circular Mega-Con-X Switchcraft connectors MIL-E-QUAL, MIL-C-5015 size fitting coupling 10SL 1/2-20 5/8-24 12S 5/8-24 3/4-20 14S 3/4-20 7/8-20 16S 7/8-20 1-20 16 7/8-20 1-20 18 1-20 1.1/8-18 20 1.1/8-18 1.1/4-18 22 1.1/4-18 1.3/8-18 24 1.3/8-18 1.1/2-18 28 1.5/8-18 1.3/4-18 MIL-C-5015 http://www.amphenol-aerospace.com/pdf/catalogs/5015_Catalog.pdf http://everyspec.com/MIL-SPECS/MIL-SPECS-MIL-DTL/download.php?spec=MIL-DTL-5015H.018627.PDF size H/accessory J/coupling 8S .5-20 UNF .5-28 UNEF 10S .625-24 UNEF .625-24 UNEF 10SL .625-24 UNEF .625-24 UNEF 12 .75-20 UNEF .75-20 UNEF 12S .75-20 UNEF .75-20 UNEF 14 .875-20 UNEF .875-20 UNEF 14S .875-20 UNEF .875-20 UNEF 16 1-20 UNEF 1-20 UNEF 16S 1-20 UNEF 1-20 UNEF 18 1.0625-18 UNEF 1.125-18 UNEF 20 1.1875-18 UNEF 1.25-18 UNEF 22 1.3125-18 UNEF 1.375-18 UNEF 24 1.4375-18 UNEF 1.5-18 UNEF 28 1.75-18 UNS 1.75-18 UNS 32 2-18 UNS 2-18 UNS 36 2.25-16 UN 2.25-16 UN 40 2.5-16 UN 2.5-16 UN 44 2.75-16 UN 2.75-16 UN 48 3-16 UN 3-16 UN 0.500-28 UNEF circular connectors, MIL-C-5015; size 8S, coupling (J) (0.5-20 UNF for accessory) 0.500-20 UNF circular connectors, MIL-C-5015; size 8S, accessory (H) (0.5-28 UNEF for coupling) 0.625-24 UNEF circular connectors, MIL-C-5015; size 10S and 10SL, coupling (J) and accessory (H) 0.750-20 UNEF circular connectors, MIL-C-5015; size 12S and 12SL, coupling (J) and accessory (H) 0.875-20 UNEF circular connectors, MIL-C-5015; size 14 and 14S, coupling (J) and accessory (H) 1-20 UNEF circular connectors, MIL-C-5015; size 16 and 16S, coupling (J) and accessory (H) 1.0625-18 UNEF circular connectors, MIL-C-5015; size 18, accessory (H) (1.125-28 UNEF for coupling) 1.125-18 UNEF circular connectors, MIL-C-5015; size 18, coupling (J) (1.0625-18 for accessory) 1.1875-18 UNEF circular connectors, MIL-C-5015; size 20, accessory (H) (1.25-18 UNEF for coupling) 1.25-18 UNEF circular connectors, MIL-C-5015; size 20, coupling (J) (1.1875-18 UNEF for accessory) 1.3125-18 UNEF circular connectors, MIL-C-5015; size 22, accessory (H) (1.375-18 UNEF for coupling) 1.375-18 UNEF circular connectors, MIL-C-5015; size 22, coupling (J) (1.3125-18 UNEF for accessory) 1.4375-18 UNEF circular connectors, MIL-C-5015; size 24, accessory (H) (1.5-18 UNEF for coupling) 1.5-18 UNEF circular connectors, MIL-C-5015; size 24, coupling (J) (1.4375-18 UNEF for accessory) 1.75-18 UNS circular connectors, MIL-C-5015; size 28, coupling (J) and accessory (H) 2-18 UNS circular connectors, MIL-C-5015; size 32, coupling (J) and accessory (H) 2.25-16 UN circular connectors, MIL-C-5015; size 36, coupling (J) and accessory (H) 2.5-16 UN circular connectors, MIL-C-5015; size 40, coupling (J) and accessory (H) 2.75-16 UN circular connectors, MIL-C-5015; size 44, coupling (J) and accessory (H) 3-16 UN circular connectors, MIL-C-5015; size 48, coupling (J) and accessory (H) MIL-C-83723 (aerospace) http://www.amphenol-aerospace.com/pdf/catalogs/83723_Matrix_Catalog.pdf size H/accessory J/mounting (panel, jam nut receptacle with bayonet) 8 .5-20 UNF .625-20 UN 10 .625-24 UNEF .75-20 UNEF 12 .75-20 UNEF .9375-20 UNEF 14 .875-20 UNEF 1-20 UNEF 16 1-20 UNEF 1.125-20 UN 18 1.0625-18 UNEF 1.25-18 UNEF 20 1.1875-18 UNEF 1.375-18 UNEF 22 1.3125-18 UNEF 1.5-20 UNEF 24 1.4375-18 UENF 1.625-18 UNEF size H/accessory mounting nut J/coupling 8 .5-20 UNF .625-20 UN .5625-24 UNEF 10 .625-24 UNEF .75-20 UNEF .6875-24 UNEF 12 .75-20 UNEF .9375-20 UNEF .875-20 UNEF 14 .875-20 UNEF 1-20 UNEF .9375-20 UNEF 16 1-20 UNEF 1.125-20 UN 1.0625-18 UNEF 18 1.0625-18 UNEF 1.25-18 UNEF 1.1875-18 UNEF 20 1.1875-18 UNEF 1.375-18 UNEF 1.3125-18 UNEF 22 1.3125-18 UNEF 1.5-20 UNEF 1.4375-18 UNEF 24 1.4375-18 UENF 1.625-18 UNEF 1.5625-18 UNEF 28 1.75-18 UNS 1.875-20 UN 1.8125-16 UN size 28 not in military standard MIL-C-83723 https://www.ametek-ecp.com/-/media/ametek-ecp/v2/files/productdownloadabledocuments/datasheets-interconnect/sealtron_mil-dtl-83723_catalog.pdf size coupling mounting shells 8 .5625-24 UNF .625-20 UNF .5-20 UNF 10 .6875-24 UNEF .750-20 UNEF .625-24 UNEF 12 .8750-20 UNEF .9375-20 UNEF .75-20 UNEF 14 .9375-20 UNEF 1-20 UNEF .875-20 UNEF 16 1.0625-18 UNEF 1.125-18 UNEF 1-20 UNEF 18 1.1875-18 UNEF 1.25-18 UNEF 1.0625-18 UNEF 20 1.3125-18 UNEF 1.375-18 UNEF 1.1875-18 UNEF 22 1.4375-18 UNEF 1.5-18 UNEF 1.3125-18 UNEF 24 1.5625-18 UNEF 1.625-18 UNEF 1.4375-18 UNEF 0.500-20 UNF circular connectors, MIL-C-83723; size 8, shell/accessory 0.563-24 UNF circular connectors, MIL-C-83723; size 8, coupling ("business end") 0.625-24 UNEF circular connectors, MIL-C-83723; size 10, shell/accessory 0.625-20 UNF circular connectors, MIL-C-83723; size 8, mounting nut 0.688-24 UNEF circular connectors, MIL-C-83723; size 10, coupling ("business end") 0.750-20 UNEF circular connectors, MIL-C-83723; size 10, mounting; size 12, shell/accessory 0.875-20 UNEF circular connectors, MIL-C-83723; size 12, coupling ("business end"); size 14, shell/accessory 0.938-20 UNEF circular connectors, MIL-C-83723; size 14, coupling ("business end"); size 12, mounting nut 1.000-20 UNEF circular connectors, MIL-C-83723; size 14, mounting; size 16, shell/accessory 1.063-18 UNEF circular connectors, MIL-C-83723; size 16, coupling ("business end"); size 18, shell/accessory 1.125-18 UNEF circular connectors, MIL-C-83723; size 16, mounting nut 1.188-18 UNEF circular connectors, MIL-C-83723; size 18, coupling ("business end"); size 20, shell/accessory 1.250-18 UNEF circular connectors, MIL-C-83723; size 18, mounting nut 1.313-18 UNEF circular connectors, MIL-C-83723; size 20, coupling ("business end"); size 22, shell/accessory 1.375-18 UNEF circular connectors, MIL-C-83723; size 20, mounting nut 1.438-18 UNEF circular connectors, MIL-C-83723; size 22, coupling ("business end");size 24, shell/accessory 1.500-18 UNEF circular connectors, MIL-C-83723; size 22, mounting nut 1.563-18 UNEF circular connectors, MIL-C-83723; size 24, coupling ("business end") 1.625-18 UNEF circular connectors, MIL-C-83723; size 24, mounting nut 1.750-18 UNS circular connectors, MIL-C-83723; size 28 (not in MIL standard?), shell/accessory 1.813-16 UN circular connectors, MIL-C-83723; size 28 (not in MIL standard?), coupling ("business end") 1.875-20 UN circular connectors, MIL-C-83723; size 28 (not in MIL standard?), mounting nut MIL-PRF-24758-2 conduit fittings http://www.advante.ru/docs/glenair/Shipboard%20interconnect%20and%20conduit%20solutions.pdf 0.438-28 UNEF conduit fittings, MIL-PRF-24758-2, size A 0.563-24 UNEF conduit fittings, MIL-PRF-24758-2, size J 0.688-24 UNEF conduit fittings, MIL-PRF-24758-2, size B 0.813-20 UNEF conduit fittings, MIL-PRF-24758-2, size K 0.938-20 UNEF conduit fittings, MIL-PRF-24758-2, size C 1.250-18 UNEF conduit fittings, MIL-PRF-24758-2, size D 1.563-18 UNEF conduit fittings, MIL-PRF-24758-2, size E 1.875-16 UN conduit fittings, MIL-PRF-24758-2, size F 2.375-16 UN conduit fittings, MIL-PRF-24758-2, size G 2.875-16 UN conduit fittings, MIL-PRF-24758-2, size H 3.375-16 UN conduit fittings, MIL-PRF-24758-2, size L MIL-PRF-24758-5 conduit-to-panel fittings 0.625-24 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size A 0.750-20 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size J 0.875-20 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size B 1.000-20 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size K 1.188-18 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size C 1.438-18 UNEF conduit-to-panel fittings, MIL-PRF-24758-5, size D 1.750-16 UN conduit-to-panel fittings, MIL-PRF-24758-5, size E 2.000-16 UN conduit-to-panel fittings, MIL-PRF-24758-5, size F 2.500-16 UN conduit-to-panel fittings, MIL-PRF-24758-5, size G 3.000-16 UN conduit-to-panel fittings, MIL-PRF-24758-5, size H 3.500-16 UN conduit-to-panel fittings, MIL-PRF-24758-5, size L stuffing tube thread 0.875-12 UN shipboard stuffing tube, ASTM F1836, US, size A 1.000-12 UN shipboard stuffing tube, ASTM F1836, US, size B 1.250-12 UN shipboard stuffing tube, ASTM F1836, US, size C,D 1.313-12 UN shipboard stuffing tube, ASTM F1836, US, size E 1.625-12 UN shipboard stuffing tube, ASTM F1836, US, size F 1.750-12 UN shipboard stuffing tube, ASTM F1836, US, size G 1.813-12 UN shipboard stuffing tube, ASTM F1836, US, size J 2.000-12 UN shipboard stuffing tube, ASTM F1836, US, size K 2.063-12 UN shipboard stuffing tube, ASTM F1836, US, size L 2.188-12 UN shipboard stuffing tube, ASTM F1836, US, size M 2.313-12 UN shipboard stuffing tube, ASTM F1836, US, size N 2.688-12 UN shipboard stuffing tube, ASTM F1836, US, size P 2.875-12 UN shipboard stuffing tube, ASTM F1836, US, size R,T 3.000-12 UN shipboard stuffing tube, ASTM F1836, US, size S,V 3.125-12 UN shipboard stuffing tube, ASTM F1836, US, size W 3.250-12 UN shipboard stuffing tube, ASTM F1836, US, size X 3.375-12 UN shipboard stuffing tube, ASTM F1836, US, size Y 3.563-12 UN shipboard stuffing tube, ASTM F1836, US, size Z 3.750-12 UN shipboard stuffing tube, ASTM F1836, US, size AA 4.000-12 UN shipboard stuffing tube, ASTM F1836, US, size BB MIL-DTL-38999 connectors: 0.625-10x3 size 9 0.750-10x3 size 11 0.875-10x3 size 13 1.000-10x3 size 15 1.1875-10x3 size 17 1.250-10x3 size 19 1.375-10x3 size 21 1.500-10x3 size 23 1.625-10x3 size 25 shells: 0.4375-28 size 9, code A 0.5625-24 size 11, code B 0.6875-24 size 13, code C 0.8125-20 size 15, code D 0.9375-20 size 17, code E 1.0625-18 size 19, code F 1.1875-18 size 21, code G 1.3125-18 size 23, code H 1.4375-18 size 25, code J coupling shell accessA nutA nutB nutC accessB 9 0.625-10x3 0.4375-28 0.6875-24 0.6875-24 0.875-20 M17x1 M12x1 11 0.750-10x3 0.5625-14 0.8125-20 0.8125-20 1.000-20 M20x1 M15x1 13 0.875-10x3 0.6875-24 0.9375-20 1.0000-20 1.125-18 M25x1 M18x1 15 1.000-10x3 0.8125-20 1.0625-18 1.125-18 1.250-18 M28x1 M22x1 17 1.1875-10x3 0.9375-20 1.1875-18 1.250-18 1.375-18 M32x1 M25x1 19 1.250-10x3 1.0625-18 1.3125-18 1.375-18 1.500-18 M35x1 M28x1 21 1.375-10x3 1.1875-18 1.4375-18 1.500-18 1.625-18 M38x1 M31x1 23 1.500-10x3 1.3125-18 1.5625-18 1.625-18 1.750-18 M41x1 M34x1 25 1.625-10x3 1.4375-18 1.6875-18 1.750-18 1.875-16 M44x1 M37x1 0.4375-28 UNEF circular connectors, MIL-DTL-38999; size 9, shell/accessory, code A, coupling is 0.625-10x3 0.5625-24 UNEF circular connectors, MIL-DTL-38999; size 11, shell/accessory, code B, coupling is 0.750-10x3 0.6875-24 UNEF circular connectors, MIL-DTL-38999; series I size 9 accessory and panel nut; size 13, shell/accessory, code C, coupling is 0.875-10x3 0.8125-20 UNEF circular connectors, MIL-DTL-38999; series I size 11 accessory and panel nut; size 15, shell/accessory, code D, coupling is 1.000-10x3 0.875-20 UNEF circular connectors, MIL-DTL-38999; series II size 9 panel nut 0.9375-20 UNEF circular connectors, MIL-DTL-38999; series I size 13 accessory; size 17 shell/accessory, code E, coupling is 1.1875-10x3 1.0000-20 UNEF circular connectors, MIL-DTL-38999; series I size 13 panel nut, series II size 11 panel nut 1.0625-18 UNEF circular connectors, MIL-DTL-38999; series I size 15 accessory; size 19 shell/accessory, code F, coupling is 1.250-10x3 1.125-18 UNEF circular connectors, MIL-DTL-38999; series I size 15 panel nut, series II size 13 panel nut 1.1875-18 UNEF circular connectors, MIL-DTL-38999; series I size 17 accessory; size 21 shell/accessory, code G, coupling is 1.375-10x3 1.250-18 UNEF circular connectors, MIL-DTL-38999; series I size 17 panel nut, series II size 15 panel nut 1.3125-18 UNEF circular connectors, MIL-DTL-38999; series I size 19 accessory; size 23 shell/accessory, code H, coupling is 1.500-10x3 1.375-18 UNEF circular connectors, MIL-DTL-38999; series I size 19 panel nut, series II size 17 panel nut 1.4375-18 UNEF circular connectors, MIL-DTL-38999; series I size 21 accessory; size 25 shell/accessory, code J, coupling is 1.625-10x3 1.500-18 UNEF circular connectors, MIL-DTL-38999; series I size 21 panel nut, series II size 19 panel nut 1.5625-18 UNEF circular connectors, MIL-DTL-38999; series I size 23 accessory 1.625-18 UNEF circular connectors, MIL-DTL-38999; series I size 23 panel nut, series II size 21 panel nut 1.6875-18 UNEF circular connectors, MIL-DTL-38999; series I size 25 accessory 1.750-18 UNS circular connectors, MIL-DTL-38999; series I size 25 panel nut, series II size 23 panel nut 1.875-16 UN circular connectors, MIL-DTL-38999; series II size 25 panel nut M12x1 circular connectors, MIL-DTL-38999; size 9 shell/accessory, code A, coupling is 0.625-10x3 M15x1 circular connectors, MIL-DTL-38999; size 11 shell/accessory, code B, coupling is 0.750-10x3 M17x1 circular connectors, MIL-DTL-38999; series III,IV size 9 panel nut M18x1 circular connectors, MIL-DTL-38999; size 13 shell/accessory, code C, coupling is 0.875-10x3 M20x1 circular connectors, MIL-DTL-38999; series III,IV size 11 panel nut M22x1 circular connectors, MIL-DTL-38999; size 15 shell/accessory, code D, coupling is 1.000-10x3 M25x1 circular connectors, MIL-DTL-38999; series III,IV size 13 panel nut; size 17 shell/accessory, code E, coupling is 1.1875-10x3 M28x1 circular connectors, MIL-DTL-38999; series III,IV size 15 panel nut; size 19 shell/accessory, code F, coupling is 1.250-10x3 M31x1 circular connectors, MIL-DTL-38999; size 21 shell/accessory, code G, coupling is 1.375-10x3 M32x1 circular connectors, MIL-DTL-38999; series III,IV size 17 panel nut M34x1 circular connectors, MIL-DTL-38999; size 23 shell/accessory, code H, coupling is 1.500-10x3 M35x1 circular connectors, MIL-DTL-38999; series III,IV size 19 panel nut M37x1 circular connectors, MIL-DTL-38999; size 25 shell/accessory, code J, coupling is 1.625-10x3 M38x1 circular connectors, MIL-DTL-38999; series III,IV size 21 panel nut M41x1 circular connectors, MIL-DTL-38999; series III,IV size 23 panel nut M44x1 circular connectors, MIL-DTL-38999; series III,IV size 25 panel nut access C 8 0.5625-24 10 0.6875-24 12 0.8125-20 14 0.9375-20 16 1.0625-18 18 1.1875-18 20 1.3125-18 22 1.4375-18 24 1.5625-18 accessA - wallmount hermetic series I, filter series I nutA - jamnut mount hermetic series I nutB - jamnut mount hermetic series II, also for sizes 8..24 (8=9...24=25) nutC - jamnut mount hermetic series III, series IV accessB - jamnut-mount hermetic series IV, wallmount series III, receptacle series III accessC - wallmount series II accessD - receptacle series III, MIL-PRF-64266 http://everyspec.com/MIL-PRF/MIL-PRF-030000-79999/MIL-PRF-64266_37947/ trapezoidal, dual-start 0.750-10x2 size 11 0.875-10x2 size 13 1.062-10x2 size 15 1.500-10x2 size 23 M15x1 size 11, backshell M18x1 size 13, backshell M22x1 size 15, backshell M34x1 size 23, backshell also MIL-PRF-28876, business-end only (backshell not specified)
10-32 AN173, AN3, 0.1900 inch dia, NF-3A 1/4-28 AN174, AN4, UNF-3A 5/16-24 AN175, AN5, UNF-3A 3..20, in 1/16 inch AN170+x - close tolerance (AN173, AN174, AN175) AN70+x - propeller (specifically AN76, hex head drilled through on each face for safety wire, hard to find, can be substituted with AN6H-45A) AN20+x - clevis bolts AN3 aircraft bolts, UNF-3A; AN23, clevis bolt; AN173, close tolerance; AN42, eye bolt (3/16 shank, 3/16 hole); NAS1103/NAS6203 shear bolts AN4 aircraft bolts, UNF-3A; AN24, clevis bolt; AN174, close tolerance; AN43, eye bolt (1/4 shank, 3/16 hole); NAS1104/NAS6204 shear bolts AN5 aircraft bolts, UNF-3A; AN25, clevis bolt; AN175, close tolerance; AN44, eye bolt (5/16 shank, 1/4 hole); AN45 eye bolt (5/16 shank, 5/16 hole); NAS1105/NAS6205 shear bolts AN6 aircraft bolts, UNF-3A; AN26, clevis bolt; AN46, eye bolt (3/8 shank, 3/8 hole); NAS1106/NAS6206 shear bolts; AN76, small aircraft propeller bolts, if hard to find use AN6H-45A AN7 aircraft bolts, UNF-3A; AN27, clevis bolt AN8 aircraft bolts, UNF-3A AN9 aircraft bolts, UNF-3A AN10 aircraft bolts, UNF-3A AN11 aircraft bolts, UNF-3A AN12 aircraft bolts, UNF-3A AN13 aircraft bolts, UNF-3A AN14 aircraft bolts, UNF-3A AN15 aircraft bolts, UNF-3A AN16 aircraft bolts, UNF-3A AN17 aircraft bolts, UNF-3A AN18 aircraft bolts, UNF-3A AN20 aircraft bolts, UNF-3A
http://victorylibrary.com/tech/thread-c.htm 1.9/64-24 chassis, fork stem, 1930-36 BT 1-24 chassis, fork stem, 1936-* BT 7/8-24 chassis, fork stem, 1929-57 45 3/8-20 chassis, star hub wheel lug, 1936-72 7/32-32 chassis, gas tank top screw, 1918-35 all, 1937-73 45 5/16-32 chassis, Zerk fitting, 1924-* 7/16-28 chassis, clutch lever, 1941-73 45 13/16-24 chassis, handlebar end screw, 1931-35 BT, 1931-39 45 7/8-24 chassis, handlebar end screw, 1936-48 BT, 1940-57 45 7/16-20 motor, head bolt, 1948-83 OHV BT; base stud nut, 1930-83 BT 7/16-16 motor, head bolt, 1940-73 45, 1930-48 SV BT, 1936-47 OHV BT 7/16-14 motor, head bolt, 1952-56 K/KH; base stud, case, 1930-83 BT 3/8-16 motor, head nut, 1929-39 45, some later G/ironheads; base stud, case, 1929-85 45/K/XL 3/8-24 motor, base stud nut, 1929-85 45/K/XL 1/4-24 motor, oil pump, cam cover, trans top, etc, common through 1976 3/4-20 fuel, Linkert bowl lock nut, 1933-64 1/4-40 fuel, Linkert needle, 1927-64 1/4-32 fuel, Linkert float lever pin, 1927-64 3/4-18 fuel, gas tank petcock, 1940-65 7/32-32 vintage Harley Davidson motorcycles; chassis, gas tank top screw, 1918-35 all, 1937-73 "45" 1/4-40 vintage Harley Davidson motorcycles; fuel, Linkert needle, 1927-64 1/4-32 vintage Harley Davidson motorcycles; fuel, Linkert float lever pin, 1927-64 1/4-24 vintage Harley Davidson motorcycles; motor, oil pump, cam cover, trans top, etc, common through 1976 5/16-32 vintage Harley Davidson motorcycles; chassis, Zerk fitting, 1924-* 3/8-24 vintage Harley Davidson motorcycles; motor, base stud nut, 1929-85 "45"/"K"/"XL" 3/8-20 vintage Harley Davidson motorcycles; chassis, star hub wheel lug, 1936-72 3/8-16 vintage Harley Davidson motorcycles; motor, head nut, 1929-39 45, some later "G"/ironheads; base stud, case, 1929-85 "45"/"K"/"XL" 7/16-28 vintage Harley Davidson motorcycles; chassis, clutch lever, 1941-73 "45" 7/16-20 vintage Harley Davidson motorcycles; motor, head bolt, 1948-83 OHV "BT"; base stud nut, 1930-83 "BT" 7/16-16 vintage Harley Davidson motorcycles; motor, head bolt, 1940-73 "45", 1930-48 SV "BT", 1936-47 OHV "BT" 7/16-14 vintage Harley Davidson motorcycles; motor, head bolt, 1952-56 "K"/"KH"; base stud, case, 1930-83 "BT" 3/4-20 vintage Harley Davidson motorcycles; fuel, Linkert bowl lock nut, 1933-64 3/4-18 vintage Harley Davidson motorcycles; fuel, gas tank petcock, 1940-65 13/16-24 vintage Harley Davidson motorcycles; chassis, handlebar end screw, 1931-35 "BT", 1931-39 "45" 7/8-24 vintage Harley Davidson motorcycles; chassis, fork stem, 1929-57 "45"; handlebar end screw, 1936-48 "BT", 1940-57 "45" 1-24 vintage Harley Davidson motorcycles; chassis, fork stem, 1936-* "BT" 1.9/64-24 vintage Harley Davidson motorcycles; chassis, fork stem, 1930-36 "BT"
https://docs.rs-online.com/a06c/0900766b80033b89.pdf M6x1 LH M8x1.25 LH M10x1.5 LH M12x1.75 LH 1/4-20 LH 5/16-28 LH 3/8-16 LH 7/16-14 LH 1/2-13 LH common BA sizes: 0,2,4,6 common BSC sizes: 5/16-26 3/8-26 7/16-26 1/2-26
https://www.tme.eu/en/katalog/stud-mounting-universal-diodes_112792/ 10-32 UNF DO-4, TO-59, TO-60, TO-62 1/4-28 UNF DO-5, TO-208, DO-203AB, TO-48, TO-49, TO-61 1/4-28 UNF, M8 3/8-24 UNF 3/4-16 UNF, M24x1.5 M12 M16x1.5, 3/4-16 UNF-2A DO-205AB M16x1.5, 1/2-20 UNF M20 M20x1.5 M4 uncommon M5 DO-4 M6 DO-5, DO-203AB M8 M8x1.25 uncommon E6 M4 E14 M12 DO-4, DO-203AA 10-32, M5x0.8 DO-5, DO-203AB 1/4-28, M6x1 DO-203AB M8 DO-8, DO-205AA 3/8-24 UNF-2A?, M12 DO-9, DO-205AB 10-32?? DO-9 3/4-16 UNF, M16x1.5, M20x1.5 DO-205AB M16x1.5, M20 DO-30, DO-205AC DO-205AC M12 DO-203 10-32 UNC 2A DO-205 10-32? DO-205AB, DO-9 3/4-16 UNF, M16x1.5; M20 DO-205AC, DO-30 1/2-20 UNF, M12 TO-10 8-32 UNC-2A, 10-32 TO-48, TO-208AA M6 TO-59 10-32 TO-61 10-32, inactive TO-63 .3125-24 UNF-2A TO-64 10-32; inactive TO-65, TO-208AC TO-83 (TO-208AD?) 10-32? TO-93, TO-209AB TO-94, TO-209AC 10-32? TO-111 10-32 TO-118, TO-209AE M20x1.5 TO-208 1/4-28 UNF-2A TO-209 1/2-20 UNF-3A TO-208AC M8 TO-209AE M20x1.5, M24x1.5, 3/4-16 UNF 3/4-16 UNF: B40 and B41 (with 3/8-24 on top), B60 (cable), B61 (3/8-16 on top) M4 semiconductor packaging, stud-mounted diodes; E6 case 8-32 semiconductor packaging, stud-mounted diodes/SCRs; some TO-10 (also 10-32) 10-32 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO4, DO-203AA; metric is M5x0.8; TO-10, TO-59, TO-61, TO-83, TO-208AD, TO-94, TO-209AC M5x0.8 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO4, DO-203AA; imperial is 10-32 UNF; TO-10, TO-59, TO-61, TO-83, TO-208AD, TO-94, TO-209AC 3/8-24 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. TO-63 1/4-28 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO5, DO-203AB, TO-48, TO-208AA; metric is M6x1 M6x1 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO5, DO-203AB, TO-48, TO-208AA; imperial is 1/4-28 UNF M8 semiconductor packaging, stud-mounted diodes/SCRs; some DO-203AB, TO-208AC 3/8-24 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO8, DO-205AA; metric is M12 M12 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO8, DO-205AA; imperial is 3/8-24 UNF; E14 case 1/2-20 UNF semiconductor packaging, stud-mounted diodes/SCRs; typ. DO-205AC, DO-30, TO-209; also M12 M16x1.5 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO9, DO-205AB; imperial is 3/4-16 UNF, some also M20x1.5 3/4-16 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO9, DO-205AB; metric is M16x1.5, some also M20x1.5 M20x1.5 semiconductor packaging, stud-mounted diodes/SCRs; typ. TO-118, TO-209AE; some DO-205AB M24x1.5 semiconductor packaging, stud-mounted diodes/SCRs 8-32 semiconductor packaging, stud-mounted diodes/SCRs; some TO-10 (also 10-32) 10-32 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO4, DO-203AA; metric is M5x0.8; TO-10, TO-59, TO-61, TO-83, TO-208AD, TO-94, TO-209AC 3/8-24 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO8, DO-205AA; metric is M12; also TO-63 1/4-28 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO5, DO-203AB, TO-48, TO-208AA; metric is M6x1 1/2-20 UNF semiconductor packaging, stud-mounted diodes/SCRs; typ. DO-205AC, DO-30, TO-209; also M12 3/4-16 UNF-2A semiconductor packaging, stud-mounted diodes/SCRs; typ. DO9, DO-205AB; metric is M16x1.5, some also M20x1.5, M24x1.5 M4 semiconductor packaging, stud-mounted diodes; E6 case M5x0.8 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO4, DO-203AA; imperial is 10-32 UNF; TO-10, TO-59, TO-61, TO-83, TO-208AD, TO-94, TO-209AC M6x1 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO5, DO-203AB, TO-48, TO-208AA; imperial is 1/4-28 UNF M8 semiconductor packaging, stud-mounted diodes/SCRs; some DO-203AB, TO-208AC M12 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO8, DO-205AA; imperial is 3/8-24 UNF; E14 case M16x1.5 semiconductor packaging, stud-mounted diodes/SCRs; typ. DO9, DO-205AB; imperial is 3/4-16 UNF, some also M20x1.5 M20x1.5 semiconductor packaging, stud-mounted diodes/SCRs; typ. TO-118, TO-209AE; some DO-205AB M24x1.5 semiconductor packaging, stud-mounted diodes/SCRs
1-20 series 97, size 24, backshell 3/4-24 https://int.rsdelivers.com/category/circular-connector-backshells/10767#PI-1|PS-100|viewtype-0|sortBy-11163|sortOrder-desc
civilian military spec orange slate multimode (62.5/125), OM1 (TIA-492AAAA) orange orange multimode (50/125), OM2 (TIA-492AAAB) aqua -- multimode 850nm (50/125), OM3 (TIA-492AAAC), OM4 (TIA-492AAAD) orange green multimode (100/140), label "100/140" yellow yellow singlemode, OS1 (TIA-492CAAA), OS2 (TIA-492CAAB) blue -- singlemode, polarization-maintaining
https://www.yamawa.com/Portals/0/resources/en/product-pdf/taps/HT-CTV_J.pdf 5.330-36 CTV5-36 5.100-24 CTV5-24 7.900-32 CTV8-32 8.100-30 CTV8-30 5.370x 5V2 6.160x 6V1 5.330-36 CTV5-36, bicycle tire valve, Japanese CTV specification 5.100-24 CTV5-24, bicycle tire valve, Japanese CTV specification 7.900-32 CTV8-32, bicycle tire valve, Japanese CTV specification 8.100-30 CTV8-30, bicycle tire valve, Japanese CTV specification 5.370-24 5V2, bicycle tire valve, Japanese CTV specification 6.160-32 6V1, bicycle tire valve, Japanese CTV specification
https://www.yamawa.com/Portals/0/resources/en/product-pdf/taps/HT-CTC_J.pdf 19.10-16 CTC 19-16 25.40-16 CTC 25-16 31.80-16 CTC 31-16 38.10-16 CTC 39-16 50.80-16 CTC 51-16 63.50-16 CTC 63-16 76.20-16 CTC 75-16 19.10-16 CTC 19-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 25.40-16 CTC 25-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 31.80-16 CTC 31-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 38.10-16 CTC 39-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 50.80-16 CTC 51-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 63.50-16 CTC 63-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 76.20-16 CTC 75-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305
https://www.yamawa.com/Portals/0/resources/en/product-pdf/taps/HT-CTG_J.pdf CTG 16 - 14 20.955 19.793 18.922 CTG 22 - 14 26.441 25.279 24.408 CTG 28 - 11 33.249 31.770 30.661 CTG 36 - 11 41.910 40.431 39.322 CTG 42 - 11 47.803 46.324 45.215 CTG 54 - 11 59.614 58.135 57.026 CTG 70 - 11 75.184 73.705 72.596 CTG 82 - 11 87.884 86.405 85.296 CTG 92 - 11 100.330 98.851 97.742 CTG 104 - 11 113.030 111.551 110.442 20.955-14 CTG 16-14, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 26.441-14 CTG 22-14, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 33.249-11 CTG 28-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 41.910-11 CTG 36-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 47.803-11 CTG 42-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 59.614-11 CTG 54-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 75.184-11 CTG 70-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 87.884-11 CTG 82-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 100.330-11 CTG 92-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 113.030-11 CTG 104-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 19.10-16 CTC 19-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 25.40-16 CTC 25-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 20.955-14 CTG 16-14, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 26.441-14 CTG 22-14, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 31.80-16 CTC 31-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 33.249-11 CTG 28-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 38.10-16 CTC 39-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 41.910-11 CTG 36-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 47.803-11 CTG 42-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 50.80-16 CTC 51-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 59.614-11 CTG 54-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 63.50-16 CTC 63-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 75.184-11 CTG 70-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 76.20-16 CTC 75-16, thin steel conduit thread, 80 deg; Japanese, JIS C 8305 @ 87.884-11 CTG 82-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 100.330-11 CTG 92-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305 @ 113.030-11 CTG 104-11, thick steel conduit thread, 55 deg; Japanese, JIS C 8305
BC 5/16-26 7.94x0.977 BC 3/8-26 9.53xx0.977 BC 7/16-26 11.11xx0.977 BC 1/2-20 12.70x1.27 BC 9/16-20 14.29x1.27 BC 5/8-20 15.88x1.27 BC 11/16-24 17.46x1.058 BC 3/4-30 19.05x0.847 BC 31/32-30 24.61x0.847 BC 1-24 25.40x1.058 BC 1.29-24 32.77x1.058 BC 1.37-24 34.80x1.058 BC 1.7/16-24 36.51x1.058 BC 1.45-24 36.83x1.058 BC 1.9/16-24 39.69x1.058 BC1.8(-56) 2.06x0.454 BC2(-56) 2.27x0.454 BC2.3(-56) 2.57x0.454 BC2.6(-56) 2.87x0.454 BC2.9(-44) 3.24x0.577 BC3.2(-40) 3.57x0.635 BC3.5(-40) 3.87x0.635 BC4(-32) 4.45x0.794 @ BC 1.8(-56) BC1.8, 2.06x0.454, bicycle thread, spoke use, spoke #15 (15ga wire, 1.82mm), light vehicles @ BC 2(-56) BC2, 2.27x0.454, bicycle thread, spoke use, spoke #14 (14ga wire, 2.03mm), utility vehicles @ BC 2.3(-56) BC2.3, 2.57x0.454, bicycle thread, spoke use, spoke #13 (13ga wire, 2.33mm), utility vehicles @ BC 2.6(-56) BC2.6, 2.87x0.454, bicycle thread, spoke use, spoke #12 (12ga wire, 2.63mm), two-wheel carts for heavy load @ BC 2.9(-44) BC2.9, 3.24x0.577, bicycle thread, spoke use, spoke #11 (11ga wire, 2.93mm), two-wheel carts for heavy load @ BC 3.2(-40) BC3.2, 3.57x0.635, bicycle thread, spoke use, spoke #10 (10ga wire, 3.23mm), two-wheel carts for heavy load @ BC 3.5(-40) BC3.5, 3.87x0.635, bicycle thread, spoke use, spoke #9 (9ga wire, 3.53mm), two-wheel carts for heavy load @ BC 4(-32) BC4, 4.45x0.794, bicycle thread, spoke use, spoke #8 (8ga wire, 4.03mm), two-wheel carts for heavy load
https://www.yamawa.com/Portals/0/resources/en/product-pdf/taps/AL-HT-STI_J.pdf
http://www.zaehlershop.com/epages/61607473.sf/en_GB/?ObjectPath=/Shops/61607473/Categories/WASSERZAEHLER M58x1.5 M7L (DIN EN ISO 4064), type Minol micro M60x2 (DIN EN ISO 4064); Minomess DM, Deltamess TK M62x2 TE1 (DIN EN ISO 4064), type Techem; Minotec, Techem-Vario M64x1 M64x2 MET (DIN EN ISO 4064), type Metrona; Evenes Minomet, Metrona 307/A M65x2 MOC or MOE (DIN EN ISO 4064), type Elster/ABB; Minomoc, Elster, Kundo, ABB, Andrae M66x1 (DIN EN ISO 4064); Minomess BR, Metrona HT2 307/1, Qundis HT2 Brunata M66x1.25 (DIN EN ISO 4064); Minomess WG, Wassergerate up to 83/84 M76x1.5 MB3 (DIN EN ISO 4064), type Minol MB3 M77x1.5 A34 (DIN EN ISO 4064), type Allmess; Minolas, Kalorimeta, Qundis AMS/Allmess M78x1.5 WE1 (DIN EN ISO 4064), type Wehrle; Minomess WE, SPX, Rosswein, ZR Neptun M80x1.5 MB2 (DIN EN ISO 4064), Type Minol MB2 G2 IST (DIN EN ISO 4064), type ISTA; Minolist; standard residential G2.1/4 MUK (DIN EN ISO 4064), type Sensus; Minomuk, Pollumuk (?)
thread on wires is usually rolled, thread used matches wire by its pitch diameter 15ga 1.8mm light vehicles, bicycles 14ga 2.0mm utility vehicles, common on bicycles 12ga 2.60mm 0.104" utility vehicles, heavy bicycle wheels 11ga some industrial bicycles, mopeds, lower-end motorcycles 10ga 3.20mm 0.124" two-wheel heavy carts, motorcycles 9ga 3.60mm 0.142" two-wheel heavy carts, motorcycles 8ga 4.00mm 0.156" two-wheel heavy carts, motorcycles 7ga 4.30mm 0.171" two-wheel heavy carts 6ga 4.87mm 0.192" two-wheel heavy carts 5ga 5.15mm 0.203" two-wheel heavy carts 4ga 5.70mm 0.224" two-wheel heavy carts threads in spoke nipples Fg2 15g Fg2.3 14g Fg2.6 13g M3 12g tripod threads https://books.google.cz/books?id=JEkXAQAAMAAJ&pg=PA41&lpg=PA41&dq=tripod+screw+depth&source=bl&ots=IkxP7OU0sF&sig=ACfU3U2NAt7OKABfZcZQTpEpqR8AifOZQQ&hl=en&sa=X&ved=2ahUKEwi124bC1MDoAhUVQkEAHShTBV04ChDoATABegQIChAB#v=onepage&q=tripod%20screw%20depth&f=false ;
0.2 0.25 0.35 0.5 0.75 1 1.25 1.5 2 3 4 5 ASME pitches 80 72 64 56 48 44 40 36 32 28 27 24 20 18 16 14 13 12 11.5 11 10 9 8 7 6 5 4.5 4 Whitworth pitches 72 60 56 48 40 36 32 28 26 24 22 20 19 18 16 14 12 11 10 9 8 7 6 5 4.5 4 3.5 3.25 3 2.875 2.75 2.625 2.5
https://en.wikipedia.org/wiki/North_American_Fire_Hose_Coupler_Incompatibilities 1/2-14NPSH firefighting, booster hose, 1/2" hoses (NFPA) 3/4-14NPSH firefighting, booster hose, 3/4" hoses (NFPA) 3/4-8 NH firefighting, booster hose, 3/4" hoses (NFPA 1963 requirement) 1-8 NH firefighting, booster hose, 3/4" hoses (NFPA 1963 requirement), 1" hoses (NFPA 1963 requirement, aka "chemical hose thread", "booster hose thread") 1-8 NH firefighting, on all nozzles for booster hose (NFPA 1963) 1-11.5 NPSH firefighting, booster hose, 1" hoses (NFPA) 1.1/4-11.5NPSH firefighting, booster hose, 1.1/4" hoses (NFPA) 1.1/2-9 NH firefighting, booster hose, 1.1/2" hoses (NFPA 1963 requirement, but not commonly used in the U.S. or Canada; see 1.1/2-11.5NPSH instead), 1.3/4" hoses (NFPA 1963 requirement) 1.1/2-11.5NPSH firefighting, booster hose, 1.1/2" hoses (used instead of 1.1/2-9 NH, contrary to NFPA 1963; result of the 1918 War Industries Board, and 1.1/2-9 NH not standardized until 1957) 3/4-11.5NH firefighting, forestry hose, 3/4" hose (Garden Hose Thread) 3/4-14NPSH firefighting, forestry hose, 3/4" hose (USDA 5100-107d specification) 3/4 forestry firefighting, forestry hose, 3/4" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 1 forestry firefighting, forestry hose, 1" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 1-11.5NPSH firefighting, forestry hose, 1" hose (USDA 5100-107d specification) 1-8 NH firefighting, forestry hose, 1" hose (NFPA 1963 requirement, a.k.a. Chemical Hose Thread) 1.1/2-11.5NPSH firefighting, forestry hose, 1.1/2" hose (USDA 5100-107d specification); 2" hose (USDA 5100-107d specification, but not in common use) 1.1/2-9 NH firefighting, forestry hose, 1.1/2" hose (USDA 5100-107d specification and NFPA 1963 requirement, but not in common use) 1.1/2 forestry firefighting, forestry hose, 1.1/2" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 2.1/2-8NPSH firefighting, forestry hose, 2.1/2" hose (USDA 5100-107d specification, but not in common use) 2.1/2-7.5 NH firefighting, forestry hose, 2.1/2" hose (USDA 5100-107d specification and NFPA 1963 requirement) 2.1/2 forestry firefighting, forestry hose, 2.1/2" hose (USDA 5100-192 specification, but only in use near the Canadian border) 4.5-4 NH firefighting, forestry hose, 4" hose 2.1/2-7.5 NH firefighting, attack hose, 2.1/2" hose (NFPA 1963 requirement), 3" hose (NFPA 1963 requirement) 3-6 NH firefighting, attack hose, 3" hose (not commonly used in the U.S.) 3-8NPSH firefighting, attack hose, 3" hose 3.1/2-6 NH firefighting, attack hose, 3.1/2" hose (NFPA 1963 requirement) 3.1/2-8NPSH firefighting, attack hose, 3" hose 2.1/2-7.5 NH firefighting, suction hose; secondary suction port on most fire engines, when the volume provided by a larger diameter hose is not needed but the flexibility of a smaller hose is 4" Storz firefighting, suction hose (100mm) 5" Storz firefighting, suction hose (125mm) 4-4 NH firefighting, supply line hose, 4" hose (NFPA 1963 requirement) 4" Storz firefighting, supply line hose, 4" hose (allowed by NFPA 1963) 4.5-4 NH firefighting, supply line hose, 4" hose 4-8NPSH firefighting, supply line hose, 4" hose 5-4 NH firefighting, supply line hose, 5" hose (NFPA 1963 requirement) 5" Storz firefighting, supply line hose, 5" hose (allowed by NFPA 1963) 6-4 NH firefighting, supply line hose, 5" hose (NFPA 1963 requirement, but not commonly used in the U.S.) 8-4 NH firefighting, supply line hose, 5" hose (NFPA 1963 requirement, but not commonly used in the U.S.; only added to NFPA 1963 in the 2003 edition) TODO: check standards: 1.1/4-11.5NPSH firefighting, booster hose, 1.1/4" hoses (NFPA) - nonexistent standard? typo on wikipedia? nonthreaded: 3/4 forestry firefighting, forestry hose, 3/4" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 1 forestry firefighting, forestry hose, 1" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 1.1/2 forestry firefighting, forestry hose, 1.1/2" hose (CAN/ULC-S551-13 specification and USDA 5100-192 specification) 2.1/2 forestry firefighting, forestry hose, 2.1/2" hose (USDA 5100-192 specification, but only in use near the Canadian border) 4" Storz firefighting, suction hose (100mm) 5" Storz firefighting, suction hose (125mm) 4" Storz firefighting, supply line hose, 4" hose (allowed by NFPA 1963) 5" Storz firefighting, supply line hose, 5" hose (allowed by NFPA 1963)
https://etd.ohiolink.edu/!etd.send_file?accession=osu1131732518&disposition=inline Bormann Fuze had 12 threads per inch many of the Schenkl Fuzes had 10 threads per inch British fuzes had 14 threads per inch Prior to the war, the standard number of threads per inch for the Bormann, Navy Watercap, and paper fuze adaptors was 12 threads per inch. Some inventors, such as Robert Parrott and Benjamin Hotchkiss, stayed with this standard. However, John Schenkl, George Ganster, and John Absterdam used a different standard. Schenkl’s percussion fuze used 9, 10, or 12 threads per inch while his early combination fuze used 14 threads per inch.264 Ganster went to even finer threads and used 16 threads per inch on his fuze while Absterdam used 11, 14, or 16 threads per inch.265 The problem was that while the army’s and navy’s Ordnance Departments had specifications for most of the equipment used by the military, no written record has been found on specifications for mechanical fuzes. It is interesting to note that 12 threads per inch remained a standard for the US Military for a number of years. Today, while 12 threads per inch is still widely used, some of the newer fuzes have a different number of threads per inch. One reason for the different number of threads per inch is the desire not to have certain fuzes mixed up with each other. This information was provided in an e-mail message from Patrick Owens, Historian, ARDEC Historical Office and Museum.
T 1/4-26 BSF basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 1/4-20 BSW basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 5/16-22 BSF basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 5/16-18 BSW basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 3/8-20 BSF basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 3/8-16 BSW basic BSF/BSW tap/die set for car work (1/4-26,20 5/16-22,18 3/8-20,16) T 2BA basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 1/4-26 BSC basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 5/16-26 BSC basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 3/8-26 BSC basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 7/16-26 BSC basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 1/2-26 BSC basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 1/4-19 BSP basic BSC/CEI tap/die set for bike work (2BA, 1/4-26, 5/16-26, 3/8-26, 7/16-26. 1/2-26, 1/4-19 BSP) T 4BA assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 2BA assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 1BA assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 0BA assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 3/16-32 BSF assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 3/16-24 BSW assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 1/4-26 BSF assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 1/4-20 BSW assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 5/16-26 BSC assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 5/16-22 BSF assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 5/16-18 BSW assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 3/8-26 BSC assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 3/8-20 BSF assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 3/8-16 BSW assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 1/8-28 BSP assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA) T 1/4-19 BSP assorted British tap/die set (3/16-32,24 1/4-26,20 5/16-26,22,18 3/8-26,20,16 1/8-28BSP 1/4-19BSP 0BA 1BA 2BA 4BA)
First choice: M2 2.5 3 4 5 6 8 10 12 16 20 24 30 36 42 Second choice: M3.5 14 18 22 27 33 39 45 Third choice: M15 17 25 40 Avoid: M7 9 11 26 28 32 35 38
@ 4.1/2(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 4.1/2(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 5(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 5(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 5.1/2(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 5.1/2(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 6.5/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 6.5/8(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 7(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 7(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 7.5/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 7.5/8(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 8.5/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 8.5/8(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 9.5/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 9.5/8(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 10.3/4(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 10.3/4(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 11.3/4(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 11.3/4(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 13.3/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 13.3/8(-5) BTC Buttress Thread Casing (BTC), taper 3:48, American Petroleum Institute API SPEC 5B @ 16(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 16(-5) BTC Buttress Thread Casing (BTC), taper 1:12, American Petroleum Institute API SPEC 5B @ 18.5/8(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 18.5/8(-5) BTC Buttress Thread Casing (BTC), taper 1:12, American Petroleum Institute API SPEC 5B @ 20(-8) CSG Round Thread Casing (8rd-CSG), taper 3:48, American Petroleum Institute API SPEC 5B @ 20(-5) BTC Buttress Thread Casing (BTC), taper 1:12, American Petroleum Institute API SPEC 5B
https://www.parker.com/literature/4400_t12%5B1%5D.pdf M12x1.5 Russian light, 6mm; DIN "L", 6mm M14x1.5 Russian light, 8mm; DIN "L", 8mm; Russian heavy, 6mm; DIN "S", 6mm M16x1.5 Russian light, 10mm; DIN "L", 10mm; Russian heavy, 8mm; DIN "S", 8mm M18x1.5 Russian light, 12mm; DIN "L", 12mm; Russian heavy, 10mm; DIN "S", 10mm M20x1.5 Russian heavy, 12mm; DIN "S", 12mm M22x1.5 DIN "L", 15mm; Russian heavy, 14mm; DIN "S", 14mm M24x1.5 Russian light, 16mm; DIN "L", 16mm; Russian heavy, 16mm; DIN "S", 16mm M26x1.5 DIN "L", 12mm M27x1.5 Russian light, 18mm M30x2 Russian light, 22mm; Russian heavy, 20mm; DIN "S", 20mm M30x1.5 DIN "L", 22mm M36x2 Russian light, 28mm; Russian heavy, 25mm; DIN "S", 25mm M36x1.5 DIN "L", 28mm M42x2 Russian heavy, 30mm M45x2 Russian light, 34mm; DIN "L", 35mm M52x2 Russian light, 42mm; DIN "L", 42mm; Russian heavy, 38mm; DIN "S", 38mm M60x2 Russian heavy, 45mm Chinese 24deg cone fittings GB3734.2 type E 160 kgf/cm2 15.7 MPa 2275 psi GB3733.2 type G 250 kgf/cm2 24.5 MPa 3555 psi GB3733.2 type J 400 kgf/cm2 39.2 MPa 5690 psi M10x1 type E/type G, 4mm and 5mm tube M12x1.25 type E/type G, 6mm M14x1.5 type E/type G, 8mm; type J, 6mm M16x1.5 type E/type G, 10mm; type J, 8mm M18x1.5 type E/type G, 12mm; type J, 10mm M20x1.5 type E/type G, 14mm; type J, 10mm M22x1.5 type E/type G, 16mm; type J, 14mm M24x1.5 type E/type G, 18mm; type J, 16mm M27x1.5 type E/type G, 20mm; type J, 18mm M30x2 type E/type G, 22mm; type J, 20mm M33x2 type E/type G, 25mm; type J, 22mm M36x2 type E/type G, 28mm; type J, 25mm M39x2 type J, 28mm M42x2 type E/type G, 32mm M45x2 type E/type G, 34mm M48x2 type E/type G, 40mm M52x2 type E/type G, 42mm GB5625.2 37deg flare GB5626.2 45deg flare GB5650 37deg and 45deg inverted flare JB1887 flat face o-ring flare inverted oring M10x1 4mm,5mm 4mm,5mm M12x1.25 6 6 4mm M14x1.5 8 8 6mm M16x1.5 10 10 8mm M18x1.5 12 12 10mm M22x1.5 14 14 13mm M24x1.5 16 16 M27x1.5 18 18 16mm M30x1.5 19mm M30x2 20 M33x2 22 M36x2 25 22mm M39x2 28 25mm M42x2 32 M45x2 34 32mm http://www-eng.lbl.gov/~shuman/NEXT/MATERIALS&COMPONENTS/Pressure_vessels/TEMA_thread.pdf ; repl: xbpc: BS 3643-1:1981 1st coarse xbpf: BS 3643-1:1981 1st fine xbp: BS 3643-1:1981 1st constant xbsc: BS 3643-1:1981 2nd coarse xbsf: BS 3643-1:1981 2nd fine xbs: BS 3643-1:1981 2nd constant xbtc: BS 3643-1:1981 3rd coarse xbtf: BS 3643-1:1981 3rd fine xbt: BS 3643-1:1981 3rd constant https://meganorm.ru/Data2/1/4294848/4294848695.htm ...continue from 95!
https://meganorm.ru/Index2/1/4293793/4293793790.htm
for bicycle spokes, old the sizes match up to Birmingham or Stubs "Iron" wire gauge....... which were used for bikes. The "E" most likly means English... 7E 38 8E 38 9E 38 10E 42 11E 36 11E 44 12E 36 12E 40 12E 42 12E 46 12E 50 13E 46 13E 56 14E 56 15E 56 16E 56 16E 56 17E 56 17E 72
T 7E 38 0.180-38, 4.57x0.668, bicycle thread tap/die, wheel spoke, #7 gauge wire
T 8E 38 0.165-38, 4.19x0.668, bicycle thread tap/die, wheel spoke, #8 gauge wire
T 9E 38 0.148-38, 3.76x0.668, bicycle thread tap/die, wheel spoke, #9 gauge wire
T 10E 42 0.134-42, 3.40x0.605, bicycle thread tap/die, wheel spoke, #10 gauge wire
T 11E 44 0.120-44, 3.05x0.577, bicycle thread tap/die, wheel spoke, #11 gauge wire T 11E 36 0.120-36, 3.05x0.706, bicycle thread tap/die, wheel spoke, #11 gauge wire
T 12E 50 0.109-50, 2.77x0.508, bicycle thread tap/die, wheel spoke, #12 gauge wire T 12E 46 0.109-46, 2.77x0.552, bicycle thread tap/die, wheel spoke, #12 gauge wire T 12E 42 0.109-42, 2.77x0.605, bicycle thread tap/die, wheel spoke, #12 gauge wire T 12E 40 0.109-40, 2.77x0.635, bicycle thread tap/die, wheel spoke, #12 gauge wire T 12E 36 0.109-36, 2.77x0.706, bicycle thread tap/die, wheel spoke, #12 gauge wire
T 13E 56 0.095-56, 2.41x0.454, bicycle thread tap/die, wheel spoke, #13 gauge wire T 13E 46 0.095-46, 2.41x0.552, bicycle thread tap/die, wheel spoke, #13 gauge wire
T 14E 56 0.083-56, 2.11x0.454, bicycle thread tap/die, wheel spoke, #14 gauge wire
T 15E 56 0.072-56, 1.83x0.454, bicycle thread tap/die, wheel spoke, #15 gauge wire
T 16E 56 0.065-56, 1.65x0.454, bicycle thread tap/die, wheel spoke, #16 gauge wire
T 17E 72 0.058-72, 1.47x0.353, bicycle thread tap/die, wheel spoke, #17 gauge wire T 17E 56 0.058-56, 1.47x0.454, bicycle thread tap/die, wheel spoke, #17 gauge wire
Standard Wire Gauge,
https://cadencescience.com/adapters/1-way-threaded-end/ml-to-5-16-28-std-thd-pb 5/16-28 1/4-18 NPT 10-32 1/4-28 DASH SIZE 2 3 4 5 6 7 8 10 12 14 16 20 24 32 40 48 Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 1 ¼ 1 ½ 2 2 ½ 3 Hose I.D. 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1 ¼ 1 ½ 2 2 ½ 3 JIC 37-Flare Thread 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 ½-12 3-12 3 ½-12 SAE O-Ring Thread 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 ½-12 NPTF Pipe Thread 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11 ½ 1 ¼-11 ½ 1 ½-11 ½ 2-11 ½ 2 ½-8 3-8 NPSM Swivel Thread 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11 ½ 1 ¼-11 ½ 1 ½-11 ½ 2-11 ½ Face Seal Thread 9/16-18 11/16-16 13/16-16 1-14 1 3/16-12 1 5/16-12 1 7/16-12 1 11/16-12 2-12 2 1/2-12 Code 61 Flange Head O.D. 1.19 1.50 1.75 2.00 2.38 2.81 3.31 4.00 Code 62 Flange Head O.D. 1.25 1.62 1.88 2.12 2.50 3.12 British Thread BSPP/BSPT 1/8-28 1/4-19 3/8-19 1/2-14 3/4-14 1-11 1 ¼-11 1 ½-11 Brake Thread 7/16-24 17/32-24 11/16-20 13/16-18 1-18 SAE 45-Flare Thread 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 11/16-24 3/4-16 7/8-14 1 1/16 -14 Inverted Flare Thread 5/16-28 3/8-24 7/16-24 1/2-20 5/8-18 11/16-18 3/4-18 7/8-18 1 1/16 -16 Compression Thread 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12 METRIC THREAD 10 12 14 16 18 20 22 24 26 27 30 33 36 42 48 M 10x1.0 M 12x1.5 M 14x1.5 M 16x1.5 M 18x1.5 M 20x1.5 M 22x1.5 M 24x1.5 M 26x1.5 M 27x2.0 M 30x2.0 M 33x2.0 M 36x2.0 M 42x2.0 M 48x2.0 5/16-24 tube coupling, brake thread ("-3"), 3/16" tube, sleeve nuts on tubes; in truck air brakes; 3/16 tube not specified by SAE 7/16-24 tube coupling, brake thread ("-4"), 1/4" tube, sleeve nuts on tubes;, in truck air brakes 17/32-24 tube coupling, brake thread ("-6"), 3/8" tube, sleeve nuts on tubes;, in truck air brakes 11/16-20 tube coupling, brake thread ("-8"), 1/2" tube, sleeve nuts on tubes;, in truck air brakes 13/16-18 tube coupling, brake thread ("-10"), 5/8" tube, sleeve nuts on tubes;, in truck air brakes 1-18 tube coupling, brake thread ("-12"), 3/4" tube, sleeve nuts on tubes;, in truck air brakes Bergeon taps, watchmaking: no, thread, drill 1 0.30x0.075 0.24 2 0.35x0.075 0.28 3 0.40x0.100 0.32 4 0.45x0.100 0.37 5 0.50x0.125 0.40 6 0.55x0.125 0.45 7 0.60x0.150 0.48 8 0.65x0.150 0.53 9 0.70x0.175 0.56 10 0.75x0.175 0.61 11 0.80x0.200 0.64 12 0.85x0.200 0.69 13 0.90x0.225 0.72 14 0.95x0.225 0.77 15 1.00x0.250 0.80 16 1.05x0.250 0.85 17 1.10x0.250 0.90 18 1.20x0.250 1.00 19 1.30x0.300 1.06 20 1.40x0.300 1.16 21 1.50x0.350 1.26 22 1.60x0.350 1.32 23 1.70x0.350 1.42 24 1.80x0.350 1.52 25 2.00x0.400 1.68 sets: Colibri, Wiru, Bergeon (Bergeon documented) Wiru set no.2: 0.40, 0.50, 0.60, 0.65, 0.70, 0.80, 0.90, 1.00, 1.10, 1.20 ,1.30, 1.40mm Wiru set 4EE: 0.70mm, 0.80mm, 0.90mm, 1.00mm, 1.10mm, 1.20mm, 1.30mm, 1.40mm Wiru set no.1: 1.00, 1.20, 1.40, 1.70, 2.00, 2.30, 2.60, 3.00mm Rolson: 1.00, 1.10, 1.20, 1.40, 1.60, 1.80, 2.00, 2.20, 2.50 Indian KMandSons: 1.40, 1.50, 1.60, 1.70, 1.80mm Jeweller's threads, sets: 0.60 - 0.80 - 0.90 -1.00 -1.20 -1.30 -1.40 -1.60 - 1.80 - 2.0 mm 0.6 0.7 0.8 0.9 1.0 1.2 1.4 1.6 1.8 2.0 M 1.0 mm (flank lead: 0.25 mm) M 1.2 mm (flank lead: 0.25 mm) M 1.4 mm (flank lead: 0.30 mm) M 1.7 mm (flank lead: 0.35 mm) M 2.0 mm (flank lead: 0.40 mm) M 2.3 mm (flank lead: 0.40 mm) M 2.6 mm (flank lead: 0.45 mm) M 3.0 mm (flank lead: 0.50 mm) Bergeon 30322 set 1x0.25, 1.2x0.0.25, 1.4x0.30, 1.7x0.35, 2x0.4, 2.3x0.4, 2.6x0.45, 3x0.5 Bergeon 30010 set Wiru set No.1 (pitch validated), == Bergeon 30322 https://www.goldschmiedebedarf.de/product_info.php?products_id=26719 M1.0x0.25 M1.2x0.25 M1.4x0.30 M1.7x0.35 M2.0x0.40 M2.3x0.40 M2.6x0.45 M3.0x0.50 in Wiru no.2 tap/die set (pitch validated) https://www.goldschmiedebedarf.de/product_info.php?products_id=26720&language=en ; M0.40x0.10 M0.50x0.125 M0.60x0.15 M0.65x0.15 M0.70x0.175 M0.80x0.20 M0.90x0.225 M1.00x0.25 M1.10x0.25 M1.20x0.25 M1.30x0.30 M1.40x0.30 Wiru 4EE: EE 0.70 / EE 0.80 / EE 0.90 / EE 1.00 / EE 1.10 / EE 1.20 / EE 1.30 / EE 1.40 EE coarse thread: 0.7..2mm in 0.1mm increment, art. 3750B coarse: 0.7..2mm, art. 3750A common cheap ebay sets: M1, M1.2, M1.4, M1.6, M1.7, M1.8, M2, M2.5, M3, M3.5 M1, M1.2, M1.4, M1.6, M1.7, M1.8, M2, M2.5, M2.6, M3.5 M1, M1.1, M1.2, M1.4, M1.6, M1.8, M2, M2.2, M2.5 0-90; 0-80; 1-64; 1-72; 2-56; 2-64; 3-48; 3-56; 4-40 Bijoutil set: M1, M1.1, M1.2, M1.4, M1.6, M1.8, M2.2, M2.5 plates: 0.7-0.8-0.9-1.0-1.1-1.2-1.3-1.4-1.5-1.6-1.7-1.8-1.9-2.0mm HI.1104 0.6-0.7-0.8-0.9-1.0mm 0.9 -1 -1.1-1.2mm Plate hole sizes imperial1-2-3-4-5 (too small for usual # designation?) 0.8, 0.9, 1, 1.1, 1.2 - HI.727 Bergeon 2776 set 0.3x0.075, 0.4x0.1, 0.5x0.125, 0.6x0.15, 0.7x0.175, 0.8x0.20, 0.9x0.225, 1x0.25 example Japanese set: https://www.practicalmachinist.com/vb/antique-machinery-and-history/tiny-marvel-swiss-tap-die-set-345158/ 1.7x0.34 1.6x0.34 1.5x0.34 1.4x0.30 1.3x0.30 1.2x0.25 1.1x0.25 1.0x0.25 0.9x0.22 0.8x0.20 0.7x0.17 0.6x0.15 0.5x0.13 0.45x0.10 0.4x0.10 Micro SAE tap/die set 00-90, 0-80, 1-64, 1-72, 2-56, 2-64 eyeglass screws: M0.6 Diameter x 0.15mm Pitch M0.8 Diameter x 0.20mm Pitch M1.0 Diameter x 0.25mm Pitch M1.16 Diameter x 0.25mm Pitch M1.2 Diameter x 0.25mm Pitch M1.3 Diameter x 0.28mm Pitch M1.4 Diameter x 0.30mm Pitch Wiru 4 table: https://mb.nawcc.org/threads/what-is-nhs-in-terms-of-threading-for-watchmaker-tap-and-die.138340/ E1 E2 L EE 2.0 2.0 2.0 2.0 18 18 18 18 16 16 16 16 14 14 14 14 12 12 13 13 10 11 12 12 8 10 11 11 6 9 10 10 5 8 9 9 4 7 8 8 E1,E2=watchmaking threads, silversmithing threads, NHS L=watch links threads, NHS EE=coarse goldsmithing threads NHS is Norm Horlogere Suisse, its thread standard is metric, same as DIN or ISO, but the latter are not defined below 1mm afaik. NHS from 0.30 to 0.90 mm have 50deg angle NHS from 1.00 to 2.00 mm have 60deg angle NHS 56100 series - find! (equal to ASME B1.10M?) in further US/UK standardization: 1.3mm dia pitch moved from 0.30 to 0.25mm, 1.60mm size omitted (Industrial Standardization, 1947) Horological Times, April 1986: http://www.awci.com/wp-content/uploads/ht/1986/1986-04-web.pdf Waltham Watch Screw Taps - Waltham Thread no. dia-tpi 1 1.50-110 3 1.20-110 5 1.10-120 7 1.00-140 9 0.93-160 11 1.34-170 13 1.00-180 15 0.83-180 17 0.65-200 19 0.55-220 21 0.45-240 23 0.35-254 metric NHS 56100 horological series 0.30x0.075 0.225 0.35x0.075 0.275 0.40x0.10 0.30 0.45x0.10 0.35 0.50x0.125 0.375 0.55x0.125 0.425 0.60x0.15 0.45 0.70x0.175 0.525 0.80x0.20 0.60 0.90x0.225 0.675 1.00x0.25 0.75 1.10x0.25 0.85 1.20x0.25 0.95 1.30x0.30 1.00 1.40x0.30 1.10 1.50x0.30 1.20 1.60x0.35 1.25 1.70x0.35 1.35 1.80x0.35 1.45 2.00x0.40 1.60 watchmaker threads are finer than jewellery threads; the latter are better for softer metals thread-rolling work-hardens material (harder longer-lasting thread), tap less likely to break watch vendors: Ball Columbus Elgin Hamilton Hampden Howard/Keystone Illinois Rockford Seth Thomas South Bend Waltham http://www.horotec.ch/_files/HOROTEC_2013-14_CD_ANG.pdf wide threading taps, EE wide thread for jewellery making 7 .8 .9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2
tapping machine taps: 3 .35 .4 .45 .5 .6 .7 .8 .9 .95 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.2 2.3 2.4 2.5 2.6 3 3.5 4 4.5 5 6
tap/die set, M 4 .5 .6 .65 .7 .8 .9 1 1.1 1.2 1.3 1.4
another set 1 1.2 1.4 1.7 2 2.3 2.6 3 Bergeon set 1.2 1.4 1.7 2 2.3 2.6 3 3.5 4 4.5 5 tap set M1, M1.2, M1.4, M1.6, M1.7, M1.8, M2, M2.5, M2.6, M3.5 thread on screw-in button pushers: 2.54mm, 2.75mm thread plates: https://www.chiark.greenend.org.uk/~alanb/martin.html Bourgeaux Plate Sizes Size Diameter (mm) Pitch (mm) 0 2.10 0.3703 1 1.95 0.3703 2 1.80 0.3125 3 1.65 0.2941 4 1.50 0.2941 5 1.35 0.2439 6 1.30 0.2777 7 1.20 0.2500 8 1.10 0.2272 9 1.00 0.2272 10 0.90 0.1923 11 0.80 0.1724 12 0.75 0.1724 13 0.70 0.1562 14 0.65 0.1470 15 0.55 0.1388 16 0.50 0.1086 17 0.45 0.1136 Watchmaker's screwplates are often found bearing makes names such as Martin, Martin et fils or Perrelet and Martin. There does not seem to be much information around on what threads these plates actually cut. Hence I have collected as much as I can find. L Latard (also called Perrelet and Martin), finer B Bourgeaux, more coarse G Gauche (Left Handed) S The number at the top of the plate is the number of holes in the plate (typically 36, 30 or 24). Conventionally there are two holes for each thread size in the plate (in case one becomes blocked, by a workpiece breaking off when in the process of being tapped). Each hole is numbered in the series which runs from 0 to 21. Typical examples 24 plate 5 through 16 30 plate 4 through 18 36 plate sizes 4 through 21 Bourgeaux thread: Also known as Bourgeaux & Delamure.; In the 19th century, a screw thread series used in Switzerland for manufacturing watches and clocks. It was realized in screw plates made by Martin, Perrelet et Martin, or Martin Fils. Plates marked “B” are the bourgeaux series. A “G” on the plate indicates left-hand threads. H 1.641x0.298 Bourgeaux thread no.3, on Martin Fils/Perrelet et Martin 'B' thread plates; watchmaking, historical H 0.414x0.101 Latard thread no.18, on Martin Fils/Perrelet et Martin 'L' thread plates; watchmaking, historical https://www.sizes.com/tools/thread_bourgeaux.htm 24 0.213 0.086 23 0.267 0.088 22 0.291 0.091 21 0.312 0.093 20 0.344 0.094 19 0.376 0.096 18 0.414 0.101 17 0.452 0.111 16 0.496 0.120 15 0.563 0.133 14 0.640 0.150 13 0.713 0.159 12 0.782 0.167 11 0.858 0.181 10 0.936 0.200 9 1.008 0.219 8 1.097 0.239 7 1.203 0.261 6 1.299 0.271 5 1.404 0.274 4 1.523 0.289 3 1.641 0.298 2 1.797 0.320 1 1.984 0.359 0 2.169 0.388 00 2.363 0.420 Latard thread: https://www.sizes.com/tools/thread_latard.htm on screw plates made by Martin, Perrelet et Martin, or Martin Fils. Plates marked “L” are the Latard series. (A “G” indicates left-hand threads.) 20 0.367 0.087 19 0.395 0.094 18 0.432 0.102 17 0.479 0.109 16 0.529 0.115 15 0.591 0.126 14 0.665 0.138 13 0.736 0.149 12 0.798 0.164 11 0.870 0.180 10 0.956 0.196 9 1.036 0.209 8 1.106 0.219 7 1.181 0.233 6 1.269 0.246 5 1.363 0.262 4 1.464 0.284 3 1.568 0.304 2 1.703 0.325 1 1.869 0.342 0 2.029 0.352 Georg W. Berndt. Die Gewinde; ihre Entwicklung, ihre Messung und ihre Toleranzen. Berlin: J. Springer, 1925. Page 66. stove bolt https://www.sizes.com/tools/thread_sb.htm manufacturers' standard, as late as 1950s H 1/8-32 stove bolt series, "SB", manufacturer standard H 5/32-30 stove bolt series, "SB", manufacturer standard H 5/32-28 stove bolt series, "SB", manufacturer standard H 3/16-24 stove bolt series, "SB", manufacturer standard H 7/32-24 stove bolt series, "SB", manufacturer standard H 7/32-22 stove bolt series, "SB", manufacturer standard H 1/4-18 stove bolt series, "SB", manufacturer standard H 5/16-18 stove bolt series, "SB", manufacturer standard H 3/8-18 stove bolt series, "SB", manufacturer standard H 3/8-16 stove bolt series, "SB", manufacturer standard H 7/16-14 stove bolt series, "SB", manufacturer standard H 1/2-13 stove bolt series, "SB", manufacturer standard https://www.sizes.com/tools/thread_ParisLM_RR.htm Compagnie des chemins de fer de Paris à Lyon et à la Méditerranée (PLM) screw thread series Around 1875. Thread angle about 36°52″ with 1/8 rounding. diameter Pitch [mm] 5 1.0 6 1.0 7 1.0 7 1.5 8 1.5 10 1.5 12 1.5 15 2.0 18 2.0 20 2.0 23 2.5 25 3.0 28 3.0 30 3.0 32 3.0 35 3.5 38 3.5 40 4.0 45 4.0 50 4.0 55 4.0 https://www.sizes.com/tools/thread_fontainemelon.htm Fontainemelon screw thread series Number Diameter Pitch Depth of external thread in millimeters 2 0.662 0.163 0.083 3 0.715 0.182 0.082 0.812 0.206 0.107 4 0.813 0.216 0.103 0.813 0.216 0.092 0.829 0.207 0.098 0.900 0.224 0.116 0.906 0.223 0.117 5 0.907 0.225 0.121 11 1.029 0.316 0.125 1.072 0.289 0.154 1.634 0.229 0.141 1.884 0.304 0.145 1.910 0.380 0.265 Georg W. Berndt. Die Gewinde; ihre Entwicklung, ihre Messung und ihre Toleranzen. Berlin: J. Springer, 1925. Page 68. https://www.sizes.com/tools/thread_mechaniker.htm Mechaniker (Siemens & Halske); screw thread series In use as late as 1925. "Post-gewinde" = Postal screw, sizes in use by the Reichspost. Number Diameter Pitch TPI deg Comment 1 15.84 0.8965 28 1/3 75 2 13.07 1.0160 25 52 3 12.30 1.4711 17 17/64 54 4 11.37 1.8246 13 23/25 59 5 11.02 1.0477 24 8/33 52 6 10.86 1.3170 19 2/7 57 7 10.16 0.9596 26 8/17 66 8 9.40 1.1545 22 52 9 9.24 1.2543 20¼ 55 10 8.91 1.5804 16 1/14 58 11 8.965 1.2192 20 5/6 50 post-gewinde 12 8.75 1.4962 16.368/377 57 13 8.28 0.9721 26 4/31 52 14 7.20 1.0367 24½ 58 post-gewinde 15 6.64 0.6047 42 58 16 6.28 1.1723 21 2/3 62 17 6.00 0.8965 28 1/3 55 post-gewinde 18 5.75 0.7815 32½ 48 post-gewinde 19 5.58 1.0367 24½ 62 20 5.30 0.5229 48 4/7 53 21 5.12 0.7815 32½ 58 post-gewinde 22 4.67 0.5229 48 4/7 62 23 4.21 0.4127 61 7/13 60 24 4.21 0.7968 31 7/8 63 25 4.00 0.6684 38 61 post-gewinde 26 3.43 0.5941 42¾ 55 27 3.37 0.6684 38 68 post-gewinde 28 2.89 0.6684 38 68 29 2.80 0.5347 47½ 66 post-gewinde 30 2.61 0.5027 50 10/19 58 31 2.16 0.4980 51 68 post-gewinde 32 1.80 0.4141 61 1/3 75 33 1.78 0.3463 73 1/3 59 post-gewinde 34 1.63 0.3023 84 55 post-gewinde 35 1.38 0.2822 90 72 36 1.22 0.2260 112 9/26 50 post-gewinde Georg W. Berndt. Die Gewinde; ihre Entwicklung, ihre Messung und ihre Toleranzen. Berlin: J. Springer, 1925. Page 115. https://www.sizes.com/tools/thread_armengaud.htm Armengaud V-thread, originally with a 76° angle. Later production switched to the 55° Whitworth thread form, at the request of Huguenin, Ducommun and Dubiet. Diameter Pitch 5.0 1.4 7.5 1.6 10.0 1.8 12.5 2.0 15.0 2.2 17.5 2.4 20.0 2.6 22.5 2.8 25.0 3.0 30.0 3.4 35.0 3.8 40.0 4.2 45.0 4.6 50.0 5.0 55.0 5.4 60.0 5.8 65.0 6.2 70.0 6.6 75.0 7.0 80.0 7.4
1841 1857 pitch — 0.100 48 — 0.125 40 — 0.150 32 — 0.175 24 — 0.200 24 — 0.225 24 ¼ 0.250 20 — 0.275 20 5/16 0.300 18 — 0.325 18 — 0.350 18 ⅜ 0.375 16 — 0.400 16 — 0.425 14 7/16 0.450 14 — 0.475 14 ½ 0.500 12 — 0.525 12 — 0.550 12 — 0.575 12 — 0.600 12 ⅝ 0.625 11 — 0.650 11 — 0.675 11 — 0.700 11 ¾ 0.750 10 — 0.800 10 ⅞ 0.875 9 — 0.900 9 1 1.000 8 1⅛ 1¼ 7 1⅜ 6 1½ 6 1⅝ 5 1¾ 5 1⅞ 4½ 2 4½ 2¼ 4 2½ 4 2¾ 3½ 3 3½ 3¼ 3¼ 3½ 3¼ 3¾ 3 4 3 4¼ 2⅞ 4½ 2⅞ 4¾ 2¾ 5 2¾ 5¼ 2⅝ 5½ 2⅝ 5¾ 2½ 6 2½ Institution of Civil Engineers. Minutes of Proceedings, Session 1841. London: The Institution, 1841. Page 159. F. Reuleaux. The Constructor. A Handbook of Machine Design. Henry Harrison Suplee, translator. New York: The Engineering Magazine, 1906. Page 51.
https://books.google.cz/books?id=2SwXAQAAIAAJ&pg=RA13-PA5&lpg=RA13-PA5&dq=%2225/64-27%22+thread&source=bl&ots=_pa0pWkZMS&sig=ACfU3U0c1ydb_o5duOiIk6BAz-jUezUghg&hl=en&sa=X&ved=2ahUKEwiL4onB4MfoAhXKasAKHQDgDJQQ6AEwAXoECAwQKA#v=onepage&q=%2225%2F64-27%22%20thread&f=false ; 1/4-32 1/4-24 5/16-20 3/8-20 7/16-18 7/16-16 1/2-18 5/8-24 11/16-20 3/4-20 3/4-18 7/8-16 1-16 1-20 1.1/16-16 1.3/8-6 2-12 for lighting fixtures (as of 1925): 1/4-27 5/16-27 3/8-27 7/16-27 1/2-27 9/16-27 5/8-27 3/4-27 7/8-27 1-27 25/64-27 omitted from table as it has only special uses railway sizes (as of 1925): straight, or taper 3/4" per foot, AN/UN form (also V-form but that's discouraged) 1/2-12 9/16-12 5/8-12 11/16-12 3/4-12 13/16-12 7/8-12 15/16-12 1-12 1.1/16-12 1.1/8-12 1.3/16-12 1.1/4-12 1.5/16-12 1.3/8-12 1.1/2-12 1.3/4-12
BSF 3/16"-32 BSF/BSC 1/4"-26 BSF 5/16"-22 BSF 3/8"-20 BSW 3/16"-24 BSW 1/4"-20 BSW 5/16"-18 BSW 3/8"-16 BSC - CEI 5/16"-26 BSC - CEI 3/8"-26 0 BA 1 BA 2 BA 4 BA BOTTOM TAP ONLY IN BSP 1/8"-28 AND BSP 1/4"-19 BSCycle CEI tap/die set 1/4" - 26 CEI 5/16" - 26 CEI 3/8" - 26 CEI 7/16" - 26 CEI 1/2" - 26 CEI 9/16" - 26 CEI (not in 5-size set) 5/8" - 26 CEI (not in 5-size set) tap/die for aviation section equipment, US military, WW2 2-56 3-48 4-36,40(,48) 5-36,40 6-32,36,40 7-32 8-32 9-32 10-24,(30),32 12-24,(32) (14-20,24) (15-20,24) (16-18,20) (18-18,20) (7/64-56) 1/8-40 9/64-40 (11/64-32) 3/16-24,32 7/32-(24),32 13/64-28 (15/64?) 1/4-20,24,32 9/32-20,24,32 bottoming taps extra: 9/64-40 5/32-38 3/16-32 15/64-28 1/4-24 assortment no.7.1/2, tap+die 5/16-20,24 3/8-20,24 7/16-18,20,24 1/2-20,24 5/8-20 5/16-20,24 left aero truck 2 56 56 3 48 48 4 36,40,48 36,40 5 36,40 36,40 6 32,36,40 32,36,40 7 32 32 8 32 32 9 32 32 10 24,30,32 24,32 12 24,32 24 14 20,24 15 20,24 16 18,20 18 18,20 7/64 56 1/8 40 40 9/64 40+ 40 11/64 32 5/32 38 3/16 24,32 24,32 13/64 28 (15/64?) 28 7/32 24,32 32 15/64 28 1/4 20,24+,32 20,24,28,32 9/32 20,24,32 20,24,32 5/16 20,24 20,24 5/16L 20,24 3/8 20,24 20,24 +/- 20 +/-24 +/-16 7/16 18,20,24 18,20,24 1/2 20,24 12,13,20,24 5/8 20 11,18 3/4 10,16 7/8 14,18 truck also: M6x1, M7x1, M8x1, M8x1.25, M9x1.25, M10x1.5, M12x1.5, M12x1.75, M14x2, M16x2, M18x1.5, M18x2.5, M20x2.5 ww2-era gas stove serviceman kit: https://books.google.cz/books?id=hm1CNnt-PVcC&pg=PA15&lpg=PA15&dq=%22no.4-36%22+tap&source=bl&ots=SW4kiQhdE_&sig=ACfU3U0PUychq6NN6RX3pVkpoKycqvAsMw&hl=en&sa=X&ved=2ahUKEwj_gezgvcroAhURDuwKHVVcATQQ6AEwBHoECAkQOQ#v=onepage&q=%22no.4-36%22%20tap&f=false ; 1/4-20 stove bolt tap 3/16-24 stove bolt tap screws: 4-36 6-32 8-32 10-24 (3/16-24 stove bolt)
https://pennchan.en.made-in-china.com/product-catalog/Fire-Extinguisher-Valve-1.html G1/8-28 f M16x1.5 f M30x1.5 m 1003 1-2kg powder/water/foam M12x1.5 f M14x1.5 f M24x1.5 m 1004 1-2kg G1/8-28 f M16x1.5 f M24x1.5 m 1005 1-2kg G1/4-19 f M16x1.5 f M30x1.5 m 1006 2-12kg 9/16-18 UNF f M16x1.5 f G7/8-14 m 1007 2-12kg M14x1.5 (outlet, f), M16x1.5 (inlet, f), M30x1.5 (bottle mount, m) 1008 (type) 2-12 kg powder/water/foam M16x1.5 f M16x1.5 f M30x1.5 m 1017 2-12kg M14x1.5 f M16x1.5 f M30x1.5 m 1018 2-12kg M16x1.5 f M16x1.5 f M30x1.5 m 1022 2-12kg M14x1.5 f M16x1.5 f M30x1.5 m 1024 2-12kg G1/8-28 f M16x1.5 f M24x1.5 m 1033 1-2kg M14x1.5 f M16x1.5 f M30x1.5 m 1035 1-2kg G1/2-14 m G1/2-14 f G1-11 m 1036 25-35kg G1/2-14 m M24x1.5 f G2-11 f/nut 1037 50-100kg G3/4-14 m G3/4-14 f G2-11 f/nut 1038 50-100 kg powder/water/foam M14x1.5 f M18x1.5,M16x1.5 f M74x2 f/nut 1041 50-100 kg "" M14x1.5/M16x1.5 f-f G3.8-19 screw valve M74x2 f/nut 1042 6-9kg cartridge/powder M14x1.5/M16x1.5 f-f M15x1.25 f M74x2 f/nut 1043 6-9kg cartridge/powder M14x1.5/M16x1.5 f-f M15x1.25 f M74x2 f/nut 1046 6-9kg cartridge/powder G1/8-28 f M16x1.5 f M30x1.5 m 1048 1-2kg M14x1.5 f M16x1.5 f M30x1.5 m 1051 1-2kg M14x1.5 f M16x1.5 f M45x1.5 f/nut 1052 6-12kg M14x1.5 f M16x1.5 f M30x1.5 m 1054 6-12kg M12x1 f M18x1.5 f M25x1.5 m 1059 1-3kg plain hole M25x1.5 m(sep.part) M30x1.5 m 1062 1-3kg M14x1.25 f M18x1.5 f M28x1.5 m 1065 1-3kg M14x1.5 f M16x1.5 f M30x1.5 m 1067 1-3kg plain hole M25x1.5 m(sep.part) M30x1.5 m 1069 1-3kg M14x1.25 f M22x1.5 f M30x1.5 m 1081 6-12kg M14x1.25 f M22x1.5 f M30x1.5 m 1083 6-12kg M14x1.5 f M16x1.5 f M30x1.5 m 1087 6-12kg M10x1 f M16x1.5 f M30x1.5 m 1097 0.5-2kg M18x1.5 f M52x1.5 m 1099 25-100kg, no valve M18x1.5 f M33x1.5 f M52x1.5 m 1100 25-100kg M14x1.5 f M16x1.5 f M30x1.5 m 1101 4-12kg G1/8-28 f M16x1.5 f M24x1.5 m 1103 1-2kg G1/4-19 f M16x1.5 f M50x2 m 1107 6-12kg M14x1.25/M16x1.5 f-f M15x1.25 f -- 1108 6-12kg M14x1.5 f M16x1.5 f M30x1.5 m 1110 6-12kg M16x1.5 f M22x1 f M34x1.5 m 1117 6-12kg 1/2-20 UNF f M16x1.5 f M30x1.5 m 1118 6-12kg W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2004 9-50kg CO2 nozzle M10x1 f PZ27.8-14 m (taper) 2005 2-9kg CO2 nozzle M10x1 f PZ27.8-14 m (taper) 2007 2-9kg CO2 W21/8-14 m M10x1 f M25x2 m 2008 2-9kg CO2, aluminium bottle W21/8-14 f M10x1 f PZ27.8-14 m (taper) 2013 2-9kg CO2, rotating valve W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2016 2-9kg CO2 W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2019 2-9kg CO2 W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2023 2-9kg CO2 W21/8-14 m M10x1 f M25x2 m 2030 2-9kg CO2, aluminium bottle W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2031 9-12kg CO2 W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2044 2-9kg CO2 W21/8-14 m G1/4-19 f PZ27.8-14 m (taper) 2046 2-9kg CO2 W21/8-14 m M10x1 f PZ27.8-14 m (taper) 2048 2-9kg CO2 nozzle M10x1 f PZ27.8-14 m (taper) 2049 2-9kg CO2 nozzle M10x1 f 1"-11.5 NPT m (taper) 2057 2-9kg CO2 nozzle 1/8-27 NPS f 1"-11.5 NPT m (taper) 2059 2-9kg CO2 W21/8-14 m M10x1 f M25x2 m 2079 10-50kg CO2 1/2-14 NPT m 3/8 NPT f (taper) 2076 10-50kg CO2, standalone valve car sensor adapters https://tuning.autodoplnky.cz/adaptery-y/y-adapter-pro-montaz-snimace-tlaku-oleje-adaptace-s1495317 car water temp oil temp oil press Alfa Romeo M16x1,5 M22x1,5 M14x1,5 Audi M14x1,5 M10x1 British Leyland 5/8-18UNF 1/8-27NPTF BMW M14x1,5 M22x1,5 M12x1,5 Citroen M18x1,5 M16x1,5 M12x1,5 Daihatsu M18x1,5 R1/8DIN2999 Fiat M16x1,5 M22x1,5 M14x1,5 Ford 1/8-27NPTF M14x1,5 1/4-18NPTF Honda M16x1,5 R1/8DIN2999 Lada M22x1,5 M14x1,5 Lancia M22x1,5 Mazda M16x1,5 M14x1,5 R1/8DIN2999 Mercedes M14x1,5 M26x1,5 Mitsubishi M14x1,5 R1/8DIN2999 Nissan M12x1,25 R1/8DIN2999 Opel M14x1,5 M14x1,5 Peugeot M18x1,5 M16x1,5 Porsche M14x1,5 M14x1,5 Renault M18x1,5 M16/18x1,5 M14x1,5 Saab 1/8-27NPTF M14x1,5 Subaru M16x1,5 R1/8DIN2999 Suzuki R1/8DIN2999 Talbot/Simca M16x1,5 M20x1,5 M12x1,5 Toyota M16x1,5 M18x1,5 R1/8DIN2999 Volkswagen M14x1,5 M10x1 Volvo M18x1,5 M18x1,5 M14x1,5 5/8-18 UNF car engine sensor port, water temperature; British Leyland R1/8 car engine sensor port, oil pressure; Daihatsu, Honda, Mazda, Mitsubishi, Nissan, Subaru, Suzuki, Toyota 1/8-27 NPTF car engine sensor port, water temperature; Ford, Saab 1/8-27 NPTF car engine sensor port, oil pressure; British Leyland 1/4-18 NPTF car engine sensor port, oil pressure; Ford
http://www.hypoptics.com/uploads/file/20190227/14/hyp-ir-lens-catalog.pdf M17x0.5 uncommon M18x0.5 M20x0.5 M23x0.5 M34x0.75 most common M34x0.5 less common M30x0.75 uncommon M45x1 M38x1 M55x1 m60x1 SWIR-MWIR: C-mount, most common M37x0.5 M30x1 M32x1 M36x1 M50x1 M60x1
popular left hand: 1.1/2-12 1.1/2-6 1.1/4-12 1.1/4-7 1.1/8-12 1.1/8-7 1.3/8-12 1.3/8-6 11/16-11 11/16-16 6-40 8-36
0.5,0.625,0.75 20,16,12 0.875,1 16,12,10 1.25,1.375,1.5 12,10,8 16,6 1.75,2,2.25,2.5 10,8,6 16,12,5,4 2.75,3,3.5,4 8,6,5 16,12,10,4 4.5,5,5.5,6 6,5,4 12,10,8,3 7,8,9,10 5,4,3 10,8,6,2.5,2 11,12,14,16 4,3,2.5 10,8,6,5,2,1.5,1.25 18,20,22,24 3,2.5,2 8,6,5,4,1.5,1.25,1 Juki sewing machines http://www.supsew.com/download/Juki/Juki%20MO-3300%20Series.pdf 1/8-44 nut 11/64-40 15/64-28 9/64-40 3/32-56
http://www.accuravalves.com/tr300.php passenger cars, bicycles, mopeds, trucks: 8V1 ext, 5V1 int large-bore valves, OTR valves, "off the road" valve 12V1 ext, 8V1 int 17V2 ext, 13V1 int 12V1 ext, 8V1 int, 13V1 ext mounting base tractor, air-liquid valve 12V1 ext, 9V1 int 8V1 ext, 5V1 int, 9V1 ext mounting base curing bags 8V1 ext, 5V1 int 12V1 ext, 8V1 int
https://www.fahrradmonteur.de/Fahrradgewinde FG14.3 on bicycles, pedals; LH+RH, 9/16-20, "normal" pedals, most common 1/2-20 on bicycles, pedals; LH+RH, in USA, and Fauber brand (BSC or also BSC?) M14x1.25 on bicycles, pedals; LH+RH, rare French pedals FG25.4 on bicycles, pedals; LH+RH, 1"-24; Shimano Dyna Drive 1.37-24 on bicycles, sprockets; freewheel BSA FG35.8 on bicycles, sprockets; freewheel ISO FG32.8 LH on bicycles, sprockets; lock ring BSA/ISO, most common, rigid pinion 35-24 on bicycles, sprockets; freewheel ITA 1.32-24 on bicycles, sprockets; ITA lock ring M35x1 on bicycles, sprockets; freewheel FRA/CH M30x1 on bicycles, sprockets; freewheel BMX, small FG25.4 on bicycles, steerer tube; standard fork, ISO, most common 1.1/8-24 on bicycles, steerer tube MTB M25x1 on bicycles, steerer tube headset, France (also FG25.4) M26x1 on bicycles, steerer tube Austria, Diamond 1.1/4-24 on bicycles, steerer tube MTB M7x1 on bicycles, bottom bracket; crank key M12x1 on bicycles, bottom bracket; crank bracket bottom bracket 18-24 LH on bicycles, bottom bracket; bottom bracket axle, Thompson 22-24 BSC LH on bicycles, bottom bracket; bottom bracket axle, Fauber 7/8-24 LH on bicycles, bottom bracket; bottom bracket axle, Fauber 23.2-32 BSC on bicycles, bottom bracket; bottom bracket axle, Fauber 15/16-24 on bicycles, bottom bracket; bottom bracket axis, Fauber M22x1 on bicycles, bottom bracket; crank trigger FG34.8 on bicycles, bottom bracket; 1.37"-24, bottom bracket cups, BSA/ISO, LH and RH; most common 35-24 on bicycles, bottom bracket; bottom bracket cups, ITA (also called "36-24"?) M35x1 on bicycles, bottom bracket; bottom bracket cups, FRA/CH (Swiss have LH thread on right side) 46-24 BSC on bicycles, bottom bracket; bottom bracket cups, Fauber; LH and RH M3 on bicycles; spokes/nipples, transport and BMX bikes M4 on bicycles; brake/gear adjustments, clamps 11/64-32 on bicycles; partial attachment of gear level W3/16-28 on bicycles; historical, mudguard struts, until about 1920; handlebar and steering damper, until about 1955 M5 on bicycles; common on luggage racks, mudguards M6x1 on bicycles; bandage screws for freewheel hub, clevis, chain tensioners, adjustments, mudguards M6x0.75 on bicycles; attachment chain wheel, Suntour brand FG6.35 on bicycles; 1/4-26, crank wedge, nuts M7x1 on bicycles; nuts, seat screws, Brooks adapter, cones, locknuts for pedal axle FG7.9 on bicycles; 5/16-26, front axle, cones and nuts M8x1.25 on bicycles; saddle clamps, nuts, clamping spindle, clamping wedge for handlebars M8x1 on bicycles; front axle, cones and nuts M8x0.75 on bicycles; fastening chainrings M9x1 on bicycles; hollow axles, front axle BMX, cones and nuts M9-26 on bicycles; M9x0.977, hollow axle, front hub Campagnolo FG9.5 on bicycles; cones and nuts, BMX 3/8-26 on bicycles; rear axle M10-26 on bicycles; M10x0.977, hollow axle, rear hub Campagnolo M10x1.5 on bicycles; side stand attachment, platter plate M10x1 on bicycles; rear axle, gearshift, bottom bracket shaft tightening 13/32-26 on bicycles; rear axle, hub gear, Sachs FG10.3 on bicycles; M10.3x0.977, hub gears Sturmey-Archer FG10.5 on bicycles; M10.5x0.977, rear axle, cones and nuts M12x1 on bicycles; bottom bracket shaft tightening 9/16-20 on bicycles, pedals; LH+RH M18x1 LH on bicycles; bottom bracket cones, locknuts M22x1 on bicycles; crank puller 32.2-32 on bicycles, bottom bracket cones, Fauber-type bottom bracket M52x1 on bicycles; sprocket locknut, sprocket attachment, crank bell M55x1 on bicycles; sprocket locknut, sprocket attachment, crank bell FG14.3 on bicycles, pedals; LH+RH, 9/16-20, "normal" pedals, most common 1/2-20 on bicycles, pedals; LH+RH, in USA, and Fauber brand (BSC or also BSC?) M14x1.25 on bicycles, pedals; LH+RH, rare French pedals FG25.4 on bicycles, pedals; LH+RH, 1"-24; Shimano Dyna Drive 1.37-24 on bicycles, sprockets; freewheel BSA FG35.8 on bicycles, sprockets; freewheel ISO FG32.8 LH on bicycles, sprockets; lock ring BSA/ISO, most common, rigid pinion 35-24 on bicycles, sprockets; freewheel ITA 1.32-24 on bicycles, sprockets; ITA lock ring M35x1 on bicycles, sprockets; freewheel FRA/CH M30x1 on bicycles, sprockets; freewheel BMX, small M25x1 on bicycles, steerer tube headset, France (also FG25.4) FG25.4 on bicycles, steerer tube; standard fork, ISO, most common M26x1 on bicycles, steerer tube Austria, Diamond 1.1/8-24 on bicycles, steerer tube MTB 1.1/4-24 on bicycles, steerer tube MTB M7x1 on bicycles, bottom bracket; crank key M12x1 on bicycles, bottom bracket; crank bracket bottom bracket 18-24 LH on bicycles, bottom bracket; bottom bracket axle, Thompson M22x1 on bicycles, bottom bracket; crank trigger 22-24 BSC LH on bicycles, bottom bracket; bottom bracket axle, Fauber 7/8-24 LH on bicycles, bottom bracket; bottom bracket axle, Fauber 23.2-32 BSC on bicycles, bottom bracket; bottom bracket axle, Fauber 15/16-24 on bicycles, bottom bracket; bottom bracket axis, Fauber FG34.8 on bicycles, bottom bracket; 1.37"-24, bottom bracket cups, BSA/ISO, LH and RH; most common 35-24 on bicycles, bottom bracket; bottom bracket cups, ITA (also called "36-24"?) M35x1 on bicycles, bottom bracket; bottom bracket cups, FRA/CH (Swiss have LH thread on right side) 46-24 BSC on bicycles, bottom bracket; bottom bracket cups, Fauber; LH and RH M3 on bicycles; spokes/nipples, transport and BMX bikes M4 on bicycles; brake/gear adjustments, clamps 11/64-32 on bicycles; partial attachment of gear level W3/16-28 on bicycles; historical, mudguard struts, until about 1920; handlebar and steering damper, until about 1955 M5 on bicycles; common on luggage racks, mudguards M6x1 on bicycles; bandage screws for freewheel hub, clevis, chain tensioners, adjustments, mudguards M6x0.75 on bicycles; attachment chain wheel, Suntour brand FG6.35 on bicycles; 1/4-26, crank wedge, nuts M7x1 on bicycles; nuts, seat screws, Brooks adapter, cones, locknuts for pedal axle FG7.9 on bicycles; 5/16-26, front axle, cones and nuts M8x1.25 on bicycles; saddle clamps, nuts, clamping spindle, clamping wedge for handlebars M8x1 on bicycles; front axle, cones and nuts M8x0.75 on bicycles; fastening chainrings M9x1 on bicycles; hollow axles, front axle BMX, cones and nuts M9-26 on bicycles; M9x0.977, hollow axle, front hub Campagnolo FG9.5 on bicycles; cones and nuts, BMX 3/8-26 on bicycles; rear axle M10-26 on bicycles; M10x0.977, hollow axle, rear hub Campagnolo M10x1.5 on bicycles; side stand attachment, platter plate M10x1 on bicycles; rear axle, gearshift, bottom bracket shaft tightening 13/32-26 on bicycles; rear axle, hub gear, Sachs FG10.3 on bicycles; M10.3x0.977, hub gears Sturmey-Archer FG10.5 on bicycles; M10.5x0.977, rear axle, cones and nuts M12x1 on bicycles; bottom bracket shaft tightening 9/16-20 on bicycles, pedals; LH+RH M18x1 LH on bicycles; bottom bracket cones, locknuts M22x1 on bicycles; crank puller 32.2-32 on bicycles, bottom bracket cones, Fauber-type bottom bracket M52x1 on bicycles; sprocket locknut, sprocket attachment, crank bell M55x1 on bicycles; sprocket locknut, sprocket attachment, crank bell
Screw-thread Standards for Federal Services, 1957, Volume 28, Issue 1 1/2-48 UNS 5/8-32 UN 3/4-32 UN 7/8-32 UN 1-32 UN 1.1/8-32 UNS 1.1/4-32 UNS 1.3/8-32 UNS 1.1/2-32 UNS 1.3/4-32 UNS 2-24 UNS 2.1/4-24 UNS 2.1/2-24 UNS 2.3/4-24 UNS 3-24 UNS 3.1/2-24 UNS
@ 0.4724 12.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 0.5313 13.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 0.5906 15.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 0.6496 16.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 0.7087 18.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 0.7677 19.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 0.8071 20.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 0.8661 22.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 0.9252 23.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 0.9843 25.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.0433 26.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 1.1024 28.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.1811 30.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 1.2205 31.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.2795 32.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.3189 33.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.3583 34.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 1.4370 36.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.4961 38.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.5551 39.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, preferred standard @ 1.6732 42.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.7913 45.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 1.9094 48.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.0276 51.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.1457 54.5x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.2441 57.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.4409-36 NS 62.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.6378 67.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 2.8346 72.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 3.0315 77.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 3.2283 82.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 3.4252 87.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 3.6220 92.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard @ 3.8189 97.0x0.706, filter thread, PH3.12, lens accessories attachment, female on lens front, US standard series, secondary standard
@ 0.9252-36 23.5x0.706, retaining rings, PH 3.17 "IV", Photographic Filter Series, US standard @ 1.3128-36 33.346x0.706, retaining rings, PH 3.17 "V", Photographic Filter Series, US standard @ 1.7459-36 44.346x0.706, retaining rings, PH 3.17 "VI", Photographic Filter Series, US standard @ 2.1396-36 54.346x0.706, retaining rings, PH 3.17 "VII", Photographic Filter Series, US standard @ 2.6317-36 66.846x0.706, retaining rings, PH 3.17 "VIII", Photographic Filter Series, US standard @ 3.4252-36 87x0.706, retaining rings, PH 3.17 "IX", Photographic Filter Series, US standard
A Treatise for Radio Mechanics, US Army Corps 1923 Air Service Information Circular, 1921
Brownells sells dia 0.020", 0.045" (0.51mm, 1.14 mm) standard wire diameters: IEC 60228 0.5 mm² 0.75 mm² 1 mm² 1.5 mm² 2.5 mm² 4 mm² 6 mm² 10 mm² 16 mm² 25 mm² 35 mm² 50 mm² 70 mm² 95 mm² 120 mm² 150 mm² 185 mm² 240 mm² 300 mm² 400 mm² 500 mm² 630 mm² 800 mm² 1000 mm²
1963 Supplement to Screw-thread Standards for Federal Services 1957 (parts I ... https://books.google.cz/books?id=NEO9ntvbeOcC&pg=PA105&lpg=PA105&dq=thread+series+changes&source=bl&ots=aK51rdrOtv&sig=ACfU3U11d2_rVNlMqPfkcjTAIbHed7eRLQ&hl=en&sa=X&ved=2ahUKEwir-NbZnoDpAhXTUxUIHTyIC8wQ6AEwD3oECAgQAQ#v=onepage&q=thread%20series%20changes&f=false
% M5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M6 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M8x1 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M10x1 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M10x1.25 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M12x1 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M12x1.25 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M12x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M14x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M16x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M18x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M20x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M22x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M24x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M26x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M27x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16; secondary size? % M27x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M30x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M30x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M33x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M33x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M36x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M36x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M38x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M39x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M39x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M42x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M42x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M45x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M45x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M48x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M48x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M52x1.5 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M52x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M56x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16 % M60x2 keg pipe thread, metric taper pipe, DIN 158; female ordinary cylindrical, male taper 1:16
@ 17 IWG 0.056-62, 1.422x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples @ 16 IWG 0.064-62, 1.626x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples @ 15 IWG 0.072-62, 1.829x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples @ 14 IWG 0.080-62, 2.032x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples @ 13 IWG 0.092-56, 2.337x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples @ 12 IWG 0.104-44, 2.642x0.41, Imperial Wire Gauge, for bicycle/motorcycle wheel spokes/nipples % M5x0.8 ISO 6149 hydraulic ports % M6x1 ISO 6149 hydraulic ports % M10x1 ISO 6149 hydraulic ports % M12x1.5 ISO 6149 hydraulic ports % M14x1.5 ISO 6149 hydraulic ports % M16x1.5 ISO 6149 hydraulic ports % M18x1.5 ISO 6149 hydraulic ports % M22x1.5 ISO 6149 hydraulic ports % M27x2 ISO 6149 hydraulic ports % M33x2 ISO 6149 hydraulic ports % M42x2 ISO 6149 hydraulic ports % M50x2 ISO 6149 hydraulic ports % M60x2 ISO 6149 hydraulic ports
Purple is for small screws, service removable. Blue is for screws over 5/16", service removable Green is for whicking (already assembled screws) and sealing porosities, approx the same strength of blue. Red is bearing and stud mount. Permanent, requires heat for removal. Amber is stronger than red.
Screw-thread Standards for Federal Services, 1957, Volume 28, Issue 1 1/2 0.770..0.776-14 3/4 0.981..0.987-14 1 1.228..1.236-11.5 1.1/4 1.573..1.581-11.5 1.1/2 1.812..1.820-11.5 2 2.286..2.294-11.5 2.1/2 2.748..2.758-8 3 3.375..3.385-8 3.1/2 3.875..3.885-8 4 4.373..4.383-8 5 5.435..5.445-8 6 6.492..6.502-8
https://www.enfield-rifles.com/screw-and-bolt-sizes-for-the-enfield_topic3330.html
https://www.pyromation.com/Catalog/pl11.pdf 1/4-28 most standard (moulding machines) 3/8-24 M6x1 M8x1.25 M10x1.5 ...also... https://eastcoastsensors.com/thermocouples.php?style_no=TF1
8-32 10-32 1/4-20 1/2-20 M5x0.8 M8x1 M10x1 M10x1.25 M12x1.25 M12x1.5 M12x1.75 process port: 1/8 NPT 1/4 NPT 1/2 NPT (standard) 3/4 NPT
https://www.vargus.com/Vargus/userdata/SendFile.asp?DBID=1&LNGID=1&GID=206 ; M1.0x0.25 M1.2x0.25 M1.4x0.25 M1.4x0.3 M1.6x0.35 M1.8x0.35 M2x0.35 M2x0.4 M2.5x0.45 0-80 1-72
https://www.ahbinc.com/files.php?get_file=Emuge%20Tap%20Drill%20Wall%20Chart.pdf&path=Cutting%20Tools ; STI-UNC Unified coarse thread ASME B18.29.1 for wire thread inserts major minor from/to drill STI-No.2-56 0.1092 0.0899 0.0961 0.0906 STI-No.3-48 0.1261 0.1036 0.1104 0.1063 STI-No.4-40 0.1445 0.1175 0.1252 0.1220 STI-No.5-40 0.1575 0.1305 0.1373 0.1339 STI-No.6-32 0.1786 0.1448 0.1527 0.1496 STI-No.8-32 0.2046 0.1708 0.1781 0.1732 STI-No.10-24 0.2441 0.1990 0.2080 0.2047 STI-No.12-24 0.2701 0.2250 0.2340 0.2283 STI-1/4-20 0.3150 0.2608 0.2704 0.2638 STI-5/16-18 0.3847 0.3245 0.3342 0.3307 STI-3/8-16 0.4562 0.3885 0.3987 0.3937 STI-7/16-14 0.5303 0.4530 0.4639 0.4567 STI-1/2-13 0.5999 0.5166 0.5273 0.5236 STI-9/16-12 0.6708 0.5806 0.5918 0.5866 STI-5/8-11 0.7431 0.6447 0.6564 0.6496 STI-3/4-10 0.8799 0.7716 0.7838 0.7776 STI-7/8-9 1.0193 0.8990 0.9119 0.9055 STI-1-8 1.1624 1.0271 1.0421 1.0335 STI-1.1/8-7 1.3106 1.1559 1.1730 1.1614 STI-1.1/4-7 1.4356 1.2809 1.2980 1.2894 STI-1.3/8-6 1.5915 1.4110 1.4310 1.4173 STI-1.1/2-6 1.7165 1.5360 1.5560 1.5453 STI-UNF Unified fine thread ASME B18.29.1 for wire thread inserts STI-No.2-64 0.1063 0.0894 0.0947 0.0906 STI-No.3-56 0.1222 0.1029 0.1086 0.1063 STI-No.4-48 0.1391 0.1166 0.1229 0.1181 STI-No.6-40 0.1705 0.1435 0.1503 0.1457 STI-No.8-36 0.2001 0.1701 0.1771 0.1732 STI-No.10-32 0.2306 0.1968 0.2041 0.2008 STI-1/4-28 0.2964 0.2577 0.2646 0.2598 STI-5/16-24 0.3666 0.3215 0.3288 0.3248 STI-3/8-24 0.4291 0.3840 0.3910 0.3858 STI-7/16-20 0.5025 0.4483 0.4561 0.4528 STI-1/2-20 0.5650 0.5108 0.5186 0.5157 STI-9/16-18 0.6347 0.5745 0.5826 0.5787 STI-5/8-18 0.6972 0.6370 0.6451 0.6398 STI-3/4-16 0.8312 0.7635 0.7720 0.7677 STI-7/8-14 0.9678 0.8905 0.8994 0.8957 STI-1-12 1.1083 1.0181 1.0281 1.0236 STI-1.1/8-12 1.2333 1.1431 1.1531 1.1516 STI-1.1/4-12 1.3583 1.2681 1.2781 1.2795 STI-1.3/8-12 1.4833 1.3931 1.4031 1.3976 STI-1.1/2-12 1.6083 1.5181 1.5281 1.5256 STI-M ISO Metric coarse thread DIN 8140-2 for wire thread inserts STI-M2x0.4 2.520 2.087 2.177 2.1 0.0827 STI-M2.5x0.45 3.084 2.597 2.697 2.65 0.1043 STI-M3x0.5 3.650 3.108 3.220 3.15 0.1240 STI-M4x0.7 4.910 4.152 4.292 4.2 0.1654 STI-M5x0.8 6.040 5.174 5.334 5.25 0.2067 STI-M6x1 7.300 6.217 6.407 6.3 0.2480 STI-M8x1.25 9.624 8.271 8.483 8.4 0.3307 STI-M10x1.5 11.948 10.324 10.560 10.5 0.4134 STI-M12x1.75 14.274 12.379 12.644 12.5 0.4921 STI-M14x2 16.598 14.433 14.733 14.5 0.5709 STI-M16x2 18.598 16.433 16.733 16.5 0.6496 STI-M18x2.5 21.248 18.541 18.896 18.75 0.7382 STI-M20x2.5 23.248 20.541 20.896 20.75 0.8169 STI-M22x2.5 25.248 22.541 22.896 22.75 0.8957 STI-M24x3 27.897 24.649 25.049 24.75 0.9744 STI-M27x3 30.897 27.649 28.049 27.75 1.0925 STI-M30x3.5 34.546 30.757 31.207 31 1.2205 cat | tr -s ' ' | awk '{print "* M" $2 "x" $3 " STI ...see " $4 "x" $3 " (screw thread insert)" }'
https://www.bowersgroup.co.uk/row/801-traditional-screw-pitch-gauges-mw800-series.html SI: 0.25, 0.3, 0.35, 0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 1.0, 1.1, 1.2, 1.25, 1.3, 1.4, 1.5, 1.6, 1.7, 1.75, 1.8, 1.9, 2.0, 2.5, 3.0 ISO: 0.35, 0.4, 0.45, 0.5, 0.6, 0.7, 0.75, 0.8, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0
https://gaugestools.com/wp-content/uploads/2017/10/Machinery%c2%b4sHandbook.pdf
Metric: British (BS 1095) French (NF E03-104) German (DIN 13) Swiss (VSM 12003)
4 holes in square/rectangle most common: 75x75mm VESA 75, MIS-D (12"..23.9", up to 14kg), M4 (usually M4x10 or M4x12) 100x100mm VESA 100, MIS-D (12"..23.9"), M4 also: 50x50 VESA 50, M4 200x100 VESA 100/200, MIS-E (24"..30.9"), M4 200x200 VESA 200, MIS-F (31" and more, have also larger rasters), M6 bolts 300x200 less common 400x300 less common 400x400 M8 bolts 600x400 800x400 800x600 900x600
ArcaSwiss style dovetail, 38.1mm (1.5") wide on wide end, 45deg sides, 5mm thick (41mm bottom, 34.41mm top gap on the mount/clamp, 4mm high) length 40mm, or 60mm RRS dovetail standard: https://www.reallyrightstuff.com/patents Bogen/Manfrotto style 25deg angle of dovetail
https://www.parktool.com/blog/repair-help/basic-thread-concepts NOMINAL THREAD SIZE EXAMPLE OF BICYCLE USES 2.2-56 Common 2mm spoke threading M3x0.5 Dropout adjustment screws, some derailleur hardware, accessory hardware M4x0.7 Some derailleur limit screws (DIN standard) M4x0.75 Common derailleur limit screw (JIS standard) M5x0.8 Many uses on bicycles, including derailleur wire pinch bolts/nuts, disc rotor mounting bolts, fender and racks mounts, water bottle cage bolts, and others M6x1 Many uses on bicycles, including brake caliper mounting bolts, brake pad bolts/nuts, some fender racks, some brake adjusting barrels M7x1 Some handlebar binder bolts 5/16-24 Front hubs, solid axle, less expensive bikes M8x1 Square-type crank bolts, front solid axle hubs, suspension system hardware M8x1.25 Stem hardware, stud type crank nuts, suspension hardware M8x0.75 Chainring bolt M9x1 Front hubs, quick release, Asian manufacturer 9-26 Front hubs, Campagnolo 3/8-24 Some solid axle bike, including coaster brake 3/8-26 Solid rear axle M10x1 Most quick release rear axles, derailleur mounting bolts, brake lever adjusting barrels 10-26 Rear axle, quick release, Campganolo M12x1 Some spline crankset bolts 1/2-20 Pedal threads, one-piece cranks 9/16-20 Pedal threads- common three piece cranks M14x1 Oversized frestyle axles M15x1 Crank bolt, Octalink and ISIS Drive 1-24 Threaded headsets, one-inch standard 1-1/8-26 Thread headset, 1-1/8 inch standard 1-1/4-26 Thread headset, 1-1/4 inch standard 1.37-24 Bottom brackets, ISO/English/BSC, and threaded freewheel hubs 1-3/8-26 Bottom brackets, older "Raleigh" three speeds 36-24 "Italian" threaded bottom brackets M47x1 T47 threaded bottom brackets
https://www.richmondau.com/product/threaded-base-plates-refplt10983-2/ M12 M10? 3/4" BSW threaded base plates for catering equipment
M4 low-cost car roof antennas, male on antenna; also M5, M6 M5x0.5 low-cost car roof antennas, male on antenna; also converters to M6 M5x0.75 low-cost car roof antennas, male on antenna; also converters to M6 M5(x0.8) low-cost car roof antennas, male on antenna; also M4, M6, M5x0.5, M5x0.75 M6 low-cost car roof antennas, female (less commonly male) on antenna; also M4, M5 aM7 low-cost car roof antennas, male on antenna; also converters to M6 10-24 low-cost car roof antennas, male on antenna; also converters to M6 5/16-18 low-cost car roof antennas, male on antenna; also converters to M6 1/4-20 low-cost car roof antennas, male or female on antenna; also converters to M6 3/8-24 UNF antenna attachment, car radios, standard on CB radios, male on antenna, very common 13/16-20 UNEF antenna attachment, NMO, usual central mount screw for 3/4" hole; see 1.1/8-18 for the main thread mount 1.1/8-18 antenna attachment, "NMO" (New Motorola), female on antenna, on cars and boats weird specials, what for? 1.13/16-20 1.13/16-18 1.13/16-16 1.13/16-14 1.13/16-12 1.13/16-10 1.13/16-8 toggle switches 1/4-40 M6x0.75 M12x1
https://www.grainger.com/category/machining/drilling-and-holemaking/counterbores-port-tools/port-tools 1.1/16-12 UN SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.3/16-12 UN SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.5/16-12 UN SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.5/8-12 UN SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.7/8-12 UN SAEJ1926-1, SAEJ514 13/16-20 UNEF 6M152, AS1300, AS4201, PS10035 1.1/8-18 UNEF 6M152, AS1300, AS4201, PS10035 5/16-24 UNF SAEJ1926-1, SAEJ514 3/8-24 UNF SAEJ1926, SAEJ514 7/16-20 UNF SAEJ1926, SAEJ514 1/2-20 UNF SAEJ1926, SAEJ514 9/16-18 UNF SAEJ1926, SAEJ514 3/4-16 UNF SAEJ1926, SAEJ514 7/8-14 UNF SAEJ1926-1, SAEJ514 2.1/2-12 UNF SAEJ1926-1, SAEJ514 1/4-28 UNJF AS5202 5/16-24 UNJF AS5202 3/8-24 UNJF AS5202, 6M152, AS1300, AS4201, PS10035 7/16-20 UNJF AS5202, 6M152, AS1300, AS4201, PS10035 1/2-20 UNJF AS5202 9/16-18 UNJF AS5202, 6M152, AS1300, AS4201, PS10035 3/4-16 UNJF AS5202 13/16-16 UNJF AS5202 1-12 UNJF AS5202 1.5/16-18 UNJF AS5202, 6M152, AS1300, AS4201, PS10035 1.5/8-12 UNJF AS5202 1.1/2-12 UNJF AS5202 7.8-14 UNJF AS5202 1/4-28 UNJF ports in scientific apparatus vessels; according to: AS5202 5/16-24 UNF ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514; AS5202 (for UNJF) 3/8-24 UNF ports in scientific apparatus vessels; according to: SAEJ1926, SAEJ514; AS5202 6M152, AS1300, AS4201, PS10035(for UNJF) 7/16-20 UNF ports in scientific apparatus vessels; according to: SAEJ1926, SAEJ514; AS5202, 6M152, AS1300, AS4201, PS10035 (for UNJF) 1/2-20 UNF ports in scientific apparatus vessels; according to: SAEJ1926, SAEJ514; AS5202 (for UNJF) 9/16-18 UNF ports in scientific apparatus vessels; according to: SAEJ1926, SAEJ514; AS5202, 6M152, AS1300, AS4201, PS10035 (for UNJF) 3/4-16 UNF ports in scientific apparatus vessels; according to: SAEJ1926, SAEJ514; AS5202 (for UNJF) 13/16-20 UNEF ports in scientific apparatus vessels; according to: 6M152, AS1300, AS4201, PS10035 13/16-16 UNJF ports in scientific apparatus vessels; according to: AS5202 7/8-14 UNF ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514 1-12 UNJF ports in scientific apparatus vessels; according to: AS5202 1.1/16-12 UN ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.1/8-18 UNEF ports in scientific apparatus vessels; according to: 6M152, AS1300, AS4201, PS10035 1.3/16-12 UN ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.5/16-18 UNJF ports in scientific apparatus vessels; according to: AS5202, 6M152, AS1300, AS4201, PS10035 1.5/16-12 UN ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.1/2-12 UNJF ports in scientific apparatus vessels; according to: AS5202 1.5/8-12 UN ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514; AS5202 (for UNJ) 1.5/8-12 UNJF ports in scientific apparatus vessels; according to: AS5202 1.7/8-12 UN ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514 2.1/2-12 UNF ports in scientific apparatus vessels; according to: SAEJ1926-1, SAEJ514
https://www.besly.com/images/BeslySpecCat.pdf #00-90 #00-98 1-56 3-48 NC (left) 4-32 NS 4-48 NF (left) 5-40 NC 6-48 NS 6-40 NF 8-24 NS 8-36 NF (left) 8-40 NS 10-28 NS 10-30 NS 10-36 NS 10-40 NS 10-48 NS 10-56 NS 10-64 NS 0.210-36 NS 12-24 NC (left) 12-28 NF (left) 12-32 NEF 12-36 NS 14-20 NS 14-24 NS 1/16-27 NPT (left) 5/32-32 NS 3/16-24 NS 3/16-32 NS 7/32-32 NS 1/4-24 NS 1/4-27 NS 1/4-28 left ...
https://www.caplugs.com/caps 1/4-36 JIC tube fittings 3/8-24 JIC tube fittings, for 3/16 tube 7/16-24 JIC tube fittings, for 1 tube 7/16-20 JIC tube fittings, for 1/4 tube 1/2-20 JIC tube fittings, for 1/4 tube, common 9/16-18 JIC tube fittings, for 3/8 tube 5/8-24 JIC tube fittings 5/8-18 JIC tube fittings, for 3/8 tube, common 3/4-20 JIC tube fittings 3/4-18 JIC tube fittings 3/4-16 JIC tube fittings, for 1/2 tube 7/8-20 JIC tube fittings, for 5/8 tube 7/8-18 JIC tube fittings, for 5/8 tube 7/8-14 JIC tube fittings, for 5/8 tube 1-20 JIC tube fittings 1-14 JIC tube fittings 1.1/16-14 JIC tube fittings, for 3/4 tube 1.1/16-12 JIC tube fittings, for 3/4 tube 1.1/8-18 JIC tube fittings 1.3/16-12 JIC tube fittings, for 7/8 tube 1.5/16-12 JIC tube fittings, for 1" tube 1.1/4-18 JIC tube fittings 1.3/8-18 JIC tube fittings 1.1/2-12 JIC tube fittings 1.5/8-12 JIC tube fittings, for 1.1/4 tube 1.3/4-12 JIC tube fittings 1.7/8-12 JIC tube fittings, for 1.1/2 tube 3-12 JIC tube fittings
https://www.cejn.com/products/hydraulics/press-check-monitoring-system/press-check-nipples/ M8x1 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 M10x1 hydraulic pressure test point nipples, Press-Check system, UNI 7707, ISO 15171-2 M12x1.5 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 M14x1.5 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 M16x1.5 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 7/16-20 UNF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 1/2-20 UNF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 9/16-18 UNF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 3/4-16 UNF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 G1/8 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 1/8-27 NPTF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 G1/4 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 1/4-18 NPTF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 G3/8 hydraulic pressure test point nipples, Press-Check system, ISO 15171-2 3/8-18 NPTF hydraulic pressure test point nipples, Press-Check system, ISO 15171-2
M8x1.5 M10x1.25 M10x1.5 M12x1.25
https://beachbuggy.at/en/47-m25 M1.1 pins on earrings M2.5 common on jewellery 1.2x? piercings; 16gauge external thread, 12g or 14g internal thread 1.6 piercings; 14ga external thread 2 piercings; 6/8/10g internal thread piercings: https://www.opentip.com/product.php?products_id=6746793 https://throwbackannie.com/piercings_guides 22g 0.6mm nose piercing, most popular 20g 0.8mm nose piercing, standard earlobe piercing; usual size done in shopping malls 18g 1mm nose piercing, internal M0.9 and M0.8, external M1.2 16g 1.2mm M1.2 external, M0.9 internal, "T0.9", also M0.8 internal (rare), sometimes 1mm internal; also #000-120 internal; cartilage/helix, conch, rook, tragus, daith, facial, cheek, septum, genital, surface 14g 1.6mm M1.6 external, M1.2 internal, "T1.2" belly button, nipple, tongue, surface, genital 12g 2mm M1.6 external, M1.2 internal, "T1.2" 10g 2.4mm M1.6 external, M1.6 internal, "T1.6"; M2 internal (also on thicker ones - 8g, 6g,... 00g) 8g 3mm 6g 4mm #2-56 internal, #4-40 internal 4g 5mm 2g 6mm 0g 8mm #8-32 internal 00g 10mm one-step-down threading: 18ga external thread on 16ga jewels 16ga external thread on 14ga jewels https://www.bodycircle.com/replacement-barbell-ends-balls-and-half-balls-stainless-steel.html 16g #000-120 internal 14g..8g M1.2 internal (1.6..3.2mm) 6g+ #2-56 (may be M1.2) (4mm and more) https://info.painfulpleasures.com/help-center/body-jewelry-threading/threading 000-120 internal 18g,16g 1.2mm internal 14g 0-80 internal 12g, 10g, 8g 2-56 internal 6g, 4g 4-40 internal 6g, 4g, 2g 8-32 internal 0g, 00g, 11mm, 13mm 16g/T0.9 14g/T1.2
earring posts: 20ga 0.8mm, 0.032 in 18ga 1.0mm, 0.04 in orthodontic screw implants: 1.4mm, 1.6mm, 2mm dia
holes: 1/16, 1/8, 3/32, 1/4, 3/8 3/32 screw M1.6 on 3mm-shank mandrels https://uk.misumi-ec.com/linked/item/10600292320/img/SEA_oth_01.gif M2 on 3mm-shank mandrels M6 on 8mm-dia holder, with 3.17 or 6mm shank, 6.35mm arbor hole 1/4 for 1/4 or 3/8 (with adapter) arbor holes
Pb70Sb30 master alloy to add antimony, 745'F melting Pb95Sn5 20-to-1, Brinell approx. 10, popular for use in Cowboy Action Shooting and standard blackpowder cartridges such as the 45-70 Government Pb94Sn6 16-to-1, Brinell approx. 11, popular for use in Cowboy Action Shooting and standard blackpowder cartridges Pb96Sn4 25-to-1, Brinell approx. 9, popular for use in Cowboy Action Shooting and standard blackpowder cartridges such as the 45-70 Government Pb97.5Sn2.5 40-to-1, Brinell approx. 8.5, softer, consistent expansion and excellent weight retention at blackpowder velocities Pb64.5Sb23Sn12.5 Brownells Foundry Bullet Casting Alloy Pb92Sb6Sn2 Brownells Hardball Bullet Casting Alloy, Brinell approx. 16, modern version of the old Lyman #2,great for use in handgun bullets and many higher velocity rifle cartridges Pb84Sb12Sn4 Brownells Linotype Bullet Casting Alloy, Brinell approx. 22, very hard alloy is ideal for higher velocity rifle bullets used when target shooting. It's a bit too hard for silhouette shooting or hunting as the alloy tends to shatter on impact with metal plates of heavy bone. If used with pure lead, a 1 to 1 blend with Linotype will produce a Hardball like alloy. ...for every 1% of tin in lead, Brinell hardness increases by 0.3
@ 1/8-40 BSW W3.175x0.635; British Standard Whitworth; 55deg @ 3/16-32 BSF W4.762x0.794; British Whitworth Fine-pitch; 55deg @ 3/16-24 BSW W4.762x1.058; British Standard Whitworth; 55deg @ 1/4-26 BSF W6.35x0.977; British Whitworth Fine-pitch; 55deg @ 1/4-20 BSW W6.35x1.27; British Standard Whitworth; 55deg @ 5/16-22 BSF W7.937x1.155; British Whitworth Fine-pitch; 55deg @ 5/16-18 BSW W7.937x1.41; British Standard Whitworth; 55deg @ 3/8-20 BSF W9.525x1.27; British Whitworth Fine-pitch; 55deg @ 3/8-16 BSW W9.525x1.588; British Standard Whitworth; 55deg @ 7/16-18 BSF W11.112x1.41; British Whitworth Fine-pitch; 55deg @ 7/16-14 BSW W11.112x1.814; British Standard Whitworth; 55deg @ 1/2-16 BSF W12.70x1.588; British Whitworth Fine-pitch; 55deg @ 1/2-12 BSW W12.70x2.117; British Standard Whitworth; 55deg @ 5/8-14 BSF W15.875x1.814; British Whitworth Fine-pitch; 55deg @ 5/8-11 BSW W15.875x2.309; British Standard Whitworth; 55deg @ 3/4-12 BSF W19.05x2.117; British Whitworth Fine-pitch; 55deg @ 3/4-10 BSW W19.05x2.54; British Standard Whitworth; 55deg @ 7/8-11 BSF W22.225x2.309; British Whitworth Fine-pitch; 55deg @ 7/8-9 BSW W22.225x2.822; British Standard Whitworth; 55deg @ 1-10 BSF W25.40x2.54; British Whitworth Fine-pitch; 55deg @ 1-8 BSW W25.40x3.175; British Standard Whitworth; 55deg
@ PG7 12.5-20, Panzergewinde, 80deg; obsolete; some cable glands for up to 7mm cable @ PG9 15.2-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 9mm cable @ PG11 18.6-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 11mm cable @ PG13.5 20.4-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 13.5mm cable, some sensors (temperature, pH) on chem/bio reactors @ PG16 22.5-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 16mm cable @ PG21 28.3-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 21mm cable @ PG29 37.0-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 29mm cable @ PG36 47.0-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 36mm cable @ PG42 54.0-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 42mm cable @ PG48 59.3-18, Panzergewinde, 80deg; obsolete; some cable glands for up to 48mm cable
https://vneshbiotorg.ru/upload/katalogi/bbi-biotech_Spare_Parts_And_Accessories_Catalogue_EN_2018.pdf M10x1 standard bioreactor lid port; "11mm port", "M10", also "10mm port", female on port PG13.5 standard bioreactor lid port; "12mm port" (alternative to M16x1.5), female on port M16x1.5 standard bioreactor lid port; "12mm port", "M16", (alternative to PG13.5), female on port M26x1 standard bioreactor lid port; "19mm port" (alternative to Rd28-8), female on port, standard port size on headplate/lid; on probes and stirrer shafts M27x2 Rd28-8 standard bioreactor lid port; "19mm port" (alternative to M26x1), female on port, standard port on headplate/lid G1.1/4 standard bioreactor side port; "25mm port", male on port M38x1.5 standard bioreactor lid stirrer port; motor flange on standard bioreactors, female on port M6 M12x?? M27x1.5 ?? "M27" ? "6mm port" M30x2 ?? stirrer M18x1.5 ports, "M18" D6 ports mixer shaft diameters: 6,10,12,14,16,18 mm reactor lid screws: M8, M16 process ports: (M8?), M10x1, M12x1, M20x1.5, G1/8, G1/4, G1/2
1.3/4 lid 1.5" label 2.5/8 lid 2" label regular mouth 2.3/8(60mm) inner, 2.3/4(70mm) outer 3.1/4 lid 2.5" label wide mouth 3(76mm) inner, 3.3/8(86mm) outer
27.43-8 PCO-1810 (1.08 in dia, 25.07 mm thread base dia, 21.74 mm inner dia, 3.8mm/0.125in pitch) http://www.imajeenyus.com/mechanical/20120508_bottle_top_threads/pco1810.pdf 27.4x2.7 PCO-1881 (24.2mm thread base dia, 25.07mm top outer dia, 2.7mm/0.106in pitch) http://www.imajeenyus.com/mechanical/20120508_bottle_top_threads/28mm-ISBT-PCO-1881-Finish-3784253-17.pdf https://cnocoutdoors.com/blogs/blog/lets-talk-about-threads PCO 1810 old Cola bottle PCO 1817 SmartWater bottle PCO 1881 new Cola bottle SP 400,410 Platypus bottles: SP 400 (old), SP 410 (new) SP 410 Sawyer mini filter SP 415 Evernew bottles SP 415 Sawyer Squeeze filter SP 415 Sawyer collapsible bottle SP 425 HydroBlu Versa Flow http://file.yizimg.com/175706/2012051520551543.pdf pitch: SP-400 18..24mm 8tpi 28..77mm 6tpi 83..120mm 5tpi SP-410 18..24mm 8tpi 28mm 6tpi SP-415 13,15mm 12tpi 18..24mm 8tpi 28,33mm 6tpi SP-425 13,15mm 12tpi SP-100 22..28,38 8tpi SP-103 26mm 8tpi SP-200 24,28mm 6tpi BA 10 1.70x0.35, 47.5 deg, British Association standard BS 93, obsolete 13-12 plastic bottle thread, SP-415,425 15-12 plastic bottle thread, SP-415,425 18-8 plastic bottle thread, SP-400,410,415 20-8 plastic bottle thread, SP-400,410,415 22-8 plastic bottle thread, SP-100,400,410,415 24-8 plastic bottle thread, SP-100,400,410,415 24-6 plastic bottle thread, SP-200,444 26-8 plastic bottle thread, SP-100,103 28x2.7 plastic bottle thread, PCO-1881, newer Coke bottles (27.4 outer dia, 24.2mm thread base dia, 25.07mm top outer dia, 2.7mm/0.106in pitch) 28-8 plastic bottle thread, PCO-1810, old Coke bottles (27.43 outer dia, 1.08 in dia, 25.07 mm thread base dia, 21.74 mm inner dia, 3.8mm/0.125in pitch) 28-8 plastic bottle thread, SP-100 28-6 plastic bottle thread, SP-200,400,410,415,444; hydration bottles and filters - Platypus, Sawyer 30-6 plastic bottle thread, SP-400 33-6 plastic bottle thread, SP-400,415,444 35-6 plastic bottle thread, SP-400 38-8 plastic bottle thread, SP-100,444 38-6 plastic bottle thread, SP-400 40-6 plastic bottle thread, SP-400 43-6 plastic bottle thread, SP-400,444 45-6 plastic bottle thread, SP-400,444 48-6 plastic bottle thread, SP-400,444 51-6 plastic bottle thread, SP-400 53-6 plastic bottle thread, SP-400,444 56-6 plastic bottle thread, SP-444 58-6 plastic bottle thread, SP-400,444 60-6 plastic bottle thread, SP-400 63-6 plastic bottle thread, SP-400,444 66-6 plastic bottle thread, SP-400 70-6 plastic bottle thread, SP-400 70-4 plastic bottle thread, SP-444 73-6 plastic bottle thread, SP-444 75-6 plastic bottle thread, SP-400,444 77-6 plastic bottle thread, SP-400 83-5 plastic bottle thread, SP-400,444 89-5 plastic bottle thread, SP-400 100-5 plastic bottle thread, SP-400 110-5 plastic bottle thread, SP-400 120-5 plastic bottle thread, SP-400 PCO-2925 PCO-3025 38mm 2-star Bericap, 3-star Bericap 45mm 26.7x9x3 plastic bottle thread, 3-start Alaska 28x2.7 plastic bottle thread, PCO-1881, 650deg 28x2.8 plastic bottle thread, PCO Corvaglia, 744deg; new, less common than PCO-1881 30x9x3 plastic bottle thread, 30/25 3-start 25-8 plastic bottle thread, 25mm ROPP 28-8 plastic bottle thread, 28mm BPF-C, 720deg (old, mostly disappeared), 28mm ROPP 30x9x3 plastic bottle thread, 30/25 3-start, 120deg 38x7.26x2 plastic bottle thread, 2-start HF Bericap 38x9x3 plastic bottle thread, 3-start CF Bericap G18x3 small PET bottles PCO28 GL24 GL44 47mm throat GL-25 (GL-24) GL-28 GL-32 (GL-33) GL-38 S-40 45mm standard (GL-45?) labware commons: GL14 wrench 17mm, aperture 9.2mm; on multiport bottles GL18 wrench 22mm, aperture 11mm, on 16mm test tubes GL25 wrench 27mm, aperture 15mm, on 100mL Erlenmeyer flasks; on 10-25mL Duran bottles GL32 wrench 32mm, aperture 20mm, on 250/500/1000mL Erlenmeyer flask, dosing devices, 50mL reagent bottles, bottom outlet on reagent bottles GL45 wrench 42mm, aperture 34mm, 50mL..25L reagent bottles, 500mL gas wash bottles, dosing devices; most common GL56 on TILT media bottles GL80 0.5..5L reagent bottles GL32 common on Duran/Schott bottles GL38 bottles GL40 common on Merck bottles/jars S40 38/430 lab bottle thread GLS80 less common: S55 S60 S - buttress thread on plastic? GPI/SPI: https://www.chinaglasscontainer.com/news/the-Glass-Packaging-Institute-Finish-Drawings.html - stash of PDFs https://www.calpaclab.com/product_images/uploaded_images/cap-neck-finishes1.jpg 400 - 360deg (1 turn) thread, most common; shallow CT, sizes 18..120, 8..5 tpi 405 - 360deg (1 turn) thread; shallow CT, depressed thread, sizes 8..132, 8..5 tpi; less common 410 - 540deg (1.5 turn) thread; medium-tall, concealed bead, sizes 18..28; 8..5 tpi 415 - 720deg (2 turn) thread, narrower threads(?), taller neck (tall CT); sizes 13..28, 12..6 tpi 425 - 720deg (2 turn) thread, narrow thread pitch, buttress; shallow CT, depressed thread, sizes 8..15, 14..12 tpi; for small vials 430 - 360deg (1 turn) thread, thick threads, top bead for better seal, pour-out, more torque; tall CT, four-cut; sizes 18..38, 8..5 tpi 2000 - lug finish, noncontinuous threads; also 2030, 2035 420 - CT for polypropylene linerless, sizes 20-100 421 - CT for polypropylene linerless, sizes 18-28 422 - CT for polypropylene linerless, sizes 20-28 423 - CT for polypropylene linerless, size 28 424 - CT for polypropylene linerless, sizes 36, 38, 43 435 - CT, pour-out, sizes 18..38 445 - CT, deep-S, sizes 45..83 450 - CT, deep, sizes 70..132 439 - on glass jugs, what's the diff? 38-439, also 38-400 and 38-430 460 - home canning jar closures - 70-460, 86-460 - all 4 tpi size 425: 8,10=14 tpi, 13,15=12 tpi size 430: 18,20,22,24 = 8tpi, 28,30,33,38 = 6 tpi size 485: 28,33,35,38,40,43,48,53,58,63 - all 6 tpi most common: 24-400, 28-400 - personal care bottles 24-410 - narrow-mouth HDPE bottles 28-400 - beverage bottles, trigger sprays 33-400 - wider mouth beverage bottles 38-400 - lab bottles, jugs; 38-740 - glass jugs 28,33,38-400 - wide-mouth HDPE bottles metal F-style canister opening sizes 1.1/4" 1.3/4" 2.7/8" common beverage/food: http://bannex.com/wp-content/uploads/2016/02/Tecnocap%20Brochure%20-%20ALL%20USA.pdf bottles: 28-400 28-1620 33-400 common cosmetics: 43-400 58-400 common jars for canning, metal lids, tall/high thread: 15-425 28-480 33-480 38-740 43-485 63-445 70G (70-450, 70-460, 70-470) 75-445 83-445 86-460 common: 8-425 tiny vials, chromatography vials, small dropper bottles 9-425 chromatography vials 10-425 chromatography vials, less common 11mm microcentrifuge tubes, autosampler, snap-top, crimp-seal 13-415, 13-425 small vials, chromatography vials 15-415 also on dropper bottles 15-425 18-400, 18-415 small vials, chromatography vials 20-400 small vials; also with glass dropper 22-400 small vials, scintillation vials 24-400, 24-415 small vials, scintillation vials, chromatography vials 24-414 primarily for environmental testing applications GL25 glass media bottles 28-400, 28-415 also sprayer pumps (400) GL32 glass media bottles 33-400, 33-430 also metal (400) 38-400, 38-430 also spigot closure, dropper tip (400); Nalgene media bottles, multiport caps, septum caps (430) 43-400 also metal GL45 glass media bottles, solvent pumps 45-400 48-400 also metal (400) 53B Nalgene and Foxx containers, also multiport caps 53-400 58-400 63-400 70-400 70-Nalgene FS70 70mm, 8tpi FS80 83B see 53B; Nalgene carboys 83-400 89-400 also metal 120-400 VersaCap specs industrial caps: https://www.thecarycompany.com/containers/closures/industrial/industrial 38-400 45-400 SC-550 50mm 51mm 61mm 63-445 63-485 70mm/6tpi 70mm/8tpi NPS-8TPI 63-485 with converter to 28-400 DIN50 waste caps: S40 GL45 DIN45 - for plastic DIN50/S50 - for space saving canisters 53B - for Nalgene plastic DIN51/S55 - for plastic DIN60/S61 - for plastic DIN71/S71 - for plastic 83B - for Nalgene plastic GL80 - for bottles GLS80 - for bottles https://www.scat-europe.com/container-thread-sizes.html GL28 - Chromsystems, Recipe, Sigma 500mL buffer GL32 - glass Duran bottles GL38 - glass Wheaton/Nalgene bottles GL38 - plastic Recipe/Biosolve/HPLC Water/Fresenius Kabi 38-430 - plastic Wheaton/Nalgene 500mL square bottle GL40/S40 - Merck/Metrohm containers S41/S42 - DIN42; plastic Agro Paris Tech 51, Polymoon GL45 - lab bottles, most common S50 - space saving canisters S51 - DIN50; like S50 with wider thread B53 - Nalgene/Polymoon containers S55 - DIN51, HP51 S60/S61 - Mauser 13, RPC Containers C59PP; "61" often on lid B63 - Nalgene containers S65 - Kautex round canisters S70/S71 - Rieke 70mm, "71" often on lid GLS80 - common wide-mouth containers B83 - Kautex, Carboy 80mm containers S90 - "D90" often on lid S95 M20x1.5 port thread on Prominent lab pumps 1/4"-28 miniature couplings, common on lab gear Swagelok threads: 18 tpi? 1/8 3/16 1/4 3/8 1/2 3/4 1 1/4 3/8 9/16 3/4 6mm 10mm 12mm threads: https://www.swagelok.com/downloads/webcatalogs/EN/ms-13-77.pdf most high-press compression fittings for HPLC, 1/16" or 1/32" outer dia tubes: #10-32 UNF 1/32" outer dia tubes: #6-40 UNF SSI fittings: 1/4-28 HPLC tubing: 360um (10,000 psi, 50/75/100/125/150 um i.d.) 1/32" (0.0025,0.004,0.005,0.007,0.01"/5000psi, 0.015,0.02"/4000psi) 1/16" (0.0025,0.004,0.005,0.007,0.01,0.013,0.015"/7000psi, 0.02"/6000psi, 0.03"/4000psi, 0.04/3000psi) 1/8" (0.062"/4000psi, 0.08in/3000psi) manometer pressure ports: M16(x2) male on port G1/4 male on port G1/2 male on port G1/8 male on port G1/4 male on port G1/2 female on port M20x1.5 ? M12x1.5 1/8 NPT standard on US manometers 1/4 NPT standard on US manometers, most common 3/8 NPT less common on US manometers 1/2 NPT standard on US manometers ...NPSM threads present as females on nonpressurized ports, eg. thermowells
G1/4 G1/2 drum/barrel threads, female: R2" Mauser 2" Tri-Sure 2"
unlike CT (continuous thread) they have pads, multiple starts, only partial twist 30-2080 38-2000 43-2010 48-2010 53-2020 53-2030 less common 58-2020 63-2030 70-2030 70-2035 less common 82-2030 less common 82-2040 89-2050 100-2055 110-2070 https://www.chinaglasscontainer.com/news/the-Glass-Packaging-Institute-Finish-Drawings.html specs size TPI leads 2000 27,38 1 1 3 2010 43,48 1 1 4 also metric 2020 53,58 1.75 1.3/4 4 also metric 2030 63,66,70,77 1.5 1.1/2 4 also metric 2035 63,66,70 1.5 1.1/2 4 deep finish 2040 77,82 1.25 1.1/4 6 2045 82 1.25 1.1/4 6 deep finish 2050 89 1 1 6 2055 100 1 1 6 2060 27..38 1 1 3? deep finish 2070 110 .875 7/8 8 2080 30,33 1 1 3? medium finish 2090 38 1 1 3 medium finish 2200 51 1.75 1.3/4 10 press-on twist-off 2210 48 2.25 2.1/4 8 press-on twist-off 2215 48 1.75,2 4 press-on twist-off 2220 58,63,66,70 1.5(58),1.25 10 press-on twist-off 2225 38 1.5,2 4 press-on twist-off 1620 22,28,33,38 8(22),6 roll-on finish 1630 28 8 roll-on finish 1651 28,38 7 top-and-side seal finish 1655 28 8 top-and-side seal finish for nonrefillable service 1660 30 6 top-and-side seal roll-on champagne finish 1680 22,25,30,31.5 10/8/7/7 roll-on finish compatible with Stel capsules, for wine and liquors 501 26 2.7 4 threaded crown finish 531,535,540,545,550,555,565,600 same thread as 501, differs in the neck underneath 22-10 glass bottle, roll-on finish compatible with Stel capsules, for wine and liquors 22-8 glass bottle, roll-on finish; 22-1620 25-8 glass bottle, roll-on finish compatible with Stel capsules, for wine and liquors 28-8 glass bottle, 28-1630 roll-on finish; 28-1655 top-and-side seal finish for nonrefillable service 28-7 glass bottle, top-and-side seal finish; 28-1651 28-6 glass bottle, roll-on finish; 28-1620 30-7 glass bottle, roll-on finish compatible with Stel capsules, for wine and liquors 30-6 glass bottle, top-and-side roll-on champaigne finish; 28-1660 31.5-7 glass bottle, roll-on finish compatible with Stel capsules, for wine and liquors 33-6 glass bottle, roll-on finish; 33-1620 38-7 glass bottle, top-and-side seal finish; 38-1651 38-6 glass bottle, roll-on finish; 38-1620 26-2.7x4 glass bottle, threaded crown finish, 4-start; 26-501, 26-531, 26-535, 26-540, 26-545, 26-550, 26-555, 26-565, 26-600 (differ by neck shape below thread) 27-1x3 glass lug vacuum-seal bottle, 3-start; 27-2000 30-1x3 glass lug vacuum-seal bottle, 3-start; 30-2080, medium-deep finish 33-1x3 glass lug vacuum-seal bottle, 3-start; 33-2080, medium-deep finish 38-2x4 glass bottle, press-on twist-off finish, 4-start; 38-2225 38-1.5x4 glass bottle, press-on twist-off finish, 4-start; 38-2225 38-1x3 glass lug vacuum-seal bottle, 3-start; 38-2000, 38-2090 (medium-deep finish, less common); 43-1x4 glass lug vacuum-seal jar, 4-start; 43-2010 48-2.25x8 glass bottle, press-on twist-off finish, 8-start; 48-2210 48-2x4 glass bottle, press-on twist-off finish, 4-start; 48-2215 48-1.75x4 glass bottle, press-on twist-off finish, 4-start; 48-2215 48-1x4 glass lug vacuum-seal jar, 4-start; 48-2010 51-1.75x10 glass bottle, press-on twist-off finish, 10-start; 51-2200 53-1.75x4 glass lug vacuum-seal jar, 4-start; 53-2020, 53-2030 (not in specs?, uncommon) 58-1.75x4 glass lug vacuum-seal jar, 4-start; 58-2020 58-1.5x10 glass bottle, press-on twist-off finish, 10-start; 58-2220 63-1.5x4 glass lug vacuum-seal jar, 4-start; 63-2030, 63-2035 (deep finish, less common) 63-1.25x10 glass bottle, press-on twist-off finish, 10-start; 63-2220 66-1.5x4 glass lug vacuum-seal jar, 4-start; 66-2030, 66-2035 (deep finish, less common) 66-1.25x10 glass bottle, press-on twist-off finish, 10-start; 66-2220 70-1.5x4 glass lug vacuum-seal jar, 4-start; 70-2030, 70-2035 (deep finish, less common); very common canning size 70-1.25x10 glass bottle, press-on twist-off finish, 10-start; 70-2220 77-1.5x4 glass lug vacuum-seal jar, 4-start; 77-2030 77-1.25x6 glass lug vacuum-seal jar, 6-start; 77-2040 82-1.25x6 glass lug vacuum-seal jar, 6-start; 82-2040, 82-2045 (deep finish, less common) 89-1x6 glass lug vacuum-seal jar, 6-start; 89-2050 100-1x6 glass lug vacuum-seal jar, 6-start; 100-2055 110-0.875x8 glass lug vacuum-seal jar, 8-start; 110-2070 sift caps 48-485 most common 63-485 coin lids (indicate how common threads are?) 70-450 regular mouth Mason jar 86-460 wide-mouth Mason jar 110-400 jars: 48-400 53-400 58-400 70-450 89-400 110-400
https://catalogue.rpc-bramlage.com/en/portals/berrybramlage/assets/12767167/screw-on-flip-top-closures/ 18-415 20-410/415 22-400 - sprays, lotion dispensers 24-410/415 common 28-400/415 31-400 33-400/410 38-400 ND: 12,14.6,18.19.19.7,19.75,20,22,23.4,23.85,24,25,26.8,27,27.4,28,30,30.55,31,32,33,38 brush applicator: ND36,ND50 screw on nozzles: ND17.5,22,23 turn-lok: ND18,22,28 overcaps: dia 33,34,41,45mm Cyllian toothpaste: ND13 (orifice size 7mm, 8.1mm) tubes: 33/400 M8 M11 S13 standard primarily in oral care M15x1.5 common size, primarily in cosmetics and technical sector Tr22 primarily on large-diameter tubes ND13 ND18x3 ND22x3 trigger sprayers: 28-410 nasal spray nozzle: 14mm neck, 17mm neck M19??? caps with valves 28-400 common 33-400 38-400 common ND27.3 ND38 sports drinks: P1310C P2977 PCO1881 8938 PP24,28
https://www.corvaglia.com/caps 1810 sensitive drinks, juices, teas, flavored waters, carbonated soft drinks; also sports drinks w/ push-pull valve 1881 bottled water, carbonated soft drinks; also sports drinks w/ push-pull valve 26.7 3-start Alaska bottled water 26/22 1-start bottled water, carbonated soft drinks 29mm edible oil snap-on dairy, edible oil... 29/25 3-start bottled water 30/25 3-start bottled water, also sports drinks w/ push-pull valve 33mm 2-start sensitive drinks, juices, teas, flavored waters 34mm edible oil snap-on dairy, edible oil... 38mm 2-start sensitive drinks, juices, teas, flavored waters 38mm 3-start also sports drinks w/ push-pull valve 48mm 3-start bottled water CESN 25/22 3-start bottled water CSN26 3-start bottled water PCO Corvaglia bottled water, carbonated soft drinks https://www.bergi-plast.de/en/caps-closures/standard-caps-closures/ https://www.ne-verpackungen.com/Shop DIN45 canister caps DIN51 canister caps DIN61 canister caps KV61 canister caps, 6mm pitch KV45 KV51 KV42 DIN40 DM35 flip tops, tube shoulders; tube dia 35mm, thread dia 12.5mm, pitch 6.35mm; also snap-in version; screw cap thread dia 13.5mm, pitch 6.36mm DM40 flip tops, tube shoulders; tube dia 40mm, snap-in DM50 flip tops, tube shoulders; tube dia 50mm, snap-in ND28 flip tops, thread dia 28.25, pitch 3mm DIN28 screw caps PCO-28 flip tops, screw caps DM28 thread dia 28.9mm, pitch 4.23mm W28 thread dia 27.6mm, pitch 4.23mm DM28 SG28x3 thread dia 28.5mm, pitch 3mm RD16x2.5 mini screw cap, thread 16x2.5 RD18x3 spout insert dropper cap, thread 18.2x3 M15 dropper cap, thread 14.4x??? 43x4 measuring caps, 38ml/40ml, screw-on screw cap 45 thread dia 45.4mm, pitch 4mm screw cap 51 thread dia 54.5mm, pitch 5mm screw cap 61 thread dia 60.5mm, pitch 6mm DIN28 thread 29.9x4, 29.8x4, 29.8x4, 28.4x7 DIN18 with pipette caps, dropper inserts; common DIN55 wide neck DIN32 wide neck DIN40 wide neck DIN68 wide neck DIN18 common on dropper bottles, 5..500mL DIN32 on widemouth small bottles DIN40 on widemouth small bottles PP28 on 100..1000mL bottles, on syrup bottles DIN22 on Meplat bottles, PP caps 20-410 smaller PET bottles, 30..100mL; screw caps plastic, aluminium 28mm ROPP PET 100mL, 250mL, 500mL, 1000mL 24-410, 24-415 small PET bottles, 100mL, 200mL, 250mL, HDPE 250mL, 300mL; screw caps, flip tops 28-410 PET bottles, 250mL, 500mL, 1000mL, trigger-spray bottles ND28 fliptops, screw caps DIN28 screw caps GL18, 20-410, 24-410, 28-410 spray pumps DMxx - number by outer diameter of the lid, threads can differ significantly or be snap-on threadless 13-415 on e-liquid dropper bottles 18-410, 20-400, 22-400 dropper caps 18-415, 20-415 CRC dropper caps 24-410 aluminium caps with sprays 15-415, 18-410 caps with dropper inserts 38-400, 1.3/4" aluminium brush caps 15-415, 15-425, 18-400, 20-400 - phenolic brush caps 18-400, 20-400 (22-400) glass and plastic dropper caps 38-400 ribbon applicator 38-400 PP caps child resistant 18-415, 20-400, 22-400 larger eliquid bottles (15..120 mL) 38-400 honey bottles, sauce/dressing bottles, very common 48-400 honey jugs 24-400 flavoring extract bottles, 8oz 24-414 hot sauce bottles, marinades, dressings 38-430 large Nalgene bottles, 1/2 or 1 gallon 53B large Nalgene bottles, 2 gallon; Nalgene jerricans 83B widemouth Nalgene bottles 70mm 6tpi Baritainer jerrican caps DIN50 Baritainer jerrican caps 3/4-16 UNF water cooler faucet, spigot on Nalgene jerricans 3/4 NPT spigot for jerricans 43-485, 48-485, 53-485, 63-485 spice caps with dual doors 48-485, 53-485, 63-485 Flapper spice caps with dual doors 43-485 spice caps with flip-off lid and shaker holes 43-485 spice grinder caps 110-400 large-diameter shaker caps 38-400 caps with foil seal removal 38-430 buttress caps 20-400, 24-400, 28-400 foil liner caps 38mm DBJ 3-start thread, on dairy and beverage bottles 0.15% UV blocker
https://www.sibo-group.eu/en/products/for-tubes/ M6x0.9 uncommon M6(x1) small tubes M6x1.25 uncommon M7(x1) "M7"; on small tubes, eg. meds, cosmetics, paints M7x1.25 much less common than M7, on small tubes M9x1 on superglue tubes M9x1.25 "M9"; ordinary-size tubes, common; also superglue M9x1.5 uncommon S9x3.2 sawtooth thread; uncommon M11(x1.5) "M11"; ordinary-size tubes, very common; on 19mm and 25mm tubes M11x1.25 much less common than M11x1.5 M12x1.25 less common than M11 M12x1.25 left very rare M13x1.25 uncommon S13x2.12 sawtooth thread; mostly on toothpaste tubes, VERY common; on 35mm tubes M14x1.5 uncommon S14x2.12 sawtooth thread; uncommon S14x4.24 sawtooth thread; uncommon Tr14x6 uncommon M15x1.25 somewhat uncommon M15x1.5 "M15"; common, on larger tubes, primarily in cosmetics and industrial sector M18x1.5 uncommon RD18 GL22 uncommon Tr22x3 larger tubes (50mm dia), on cosmetics, standard, very common S22x3 sawtooth thread; uncommon S24x2.5 sawtooth thread; uncommon Tr29 uncommon Tr29 quick turn
3.1/2-11 UN fine thread, low pressure 3.1/2-8 UN coarse thread, low pressure 3.1/8-11 UN fine thread, high pressure 3.1/8-7 UN coarse thread, high-pressure W80-11 Whitworth, high pressure M120-11 M78x2.5 W95-11 Whitworth PB80 PB78 PB26 3.1/2-11 UN safety caps/neck rings on pressurized gas cylinders, "fine thread", low pressure 3.1/2-8 UN safety caps/neck rings on pressurized gas cylinders, UN coarse thread, low pressure 3.1/8-11 UN safety caps/neck rings on pressurized gas cylinders, UN fine thread, high pressure 3.1/8-7 UN safety caps/neck rings on pressurized gas cylinders, UN coarse thread, high-pressure W80-11 safety caps/neck rings on pressurized gas cylinders, Whitworth, high pressure
https://www.sherwoodvalve.com/sites/default/files/gsvt-vertical-outlet-acetylene-valve-datasheet_c.pdf 3/8-18 NGT 1/2-14 NGT 1/4-18 NPT male on bottle 1.1/8-12 UNF 3/4-14 NGT 3/4-14 SGT 1-11.5 NGT 1/2-14 NPT 3/4-14 NPT male on bottle 17.4 ISO/DIS 11116 25.8 ISO/DIS and DIN 28.8 M25x2 W19.8 DIN 477 W28.8 DIN 477 W31.3 DIN 3/4-14 NPSM JIS 20x14 JIS 28x14 JIS 28x14, reduced length 1-14 AS2473, BS341 0.06-14 AS2473 0.715-14 AS2473, tapered thread, 1:8 taper, BS341 thread gauges: https://www.lronning.com/Products/Valve-Thread-Inspection-of-cylinders W25E 17E 25T 1.025-14 BS341 oxygen bottles for hospitals/EMS, on bottle itself: 3/4-16 UNF o-ring seal, aluminium cylinders 1/2-14 NGT steel cylinders 5/8-18 UNF composite cylinders
G1/2 !G3/4 - most common on garden faucets G1 hose inner outer 3/8" 10 14.5 1/2" 12.7 17 5/8" 16 22 3/4" 19 26 1" 25 35 5/4" 32 40 6/4" 38 48
https://dengarden.com/gardening/The-Complete-Guide-to-Hose-Fittings https://www.homeownershub.com/maintenance/what-is-the-exact-tap-die-size-for-a-usa-garden-hose-threa-458832-.htm US/Canada: garden hose thread (GHT), also called national hose (NH) NHR, thin-walled rolled couplers NH, full-formed threads in bulk material by internal diameter of hose 3/4-11.5 NH, or GHT, NHR, typical on garden faucets, male on faucet 5/8-11.5 NH 1/2" - older UK: G3/4(-14), typical indoor and garden, male on faucet; also washing machine inlets G7/8, G1, typical in farms, factories, horticulture typical hose diameters: 3/8, 5/8 for domestic, 3/4 for professional use https://www.firehosedirect.com/fire-hoses-nh-vs-npsh https://www.fittings.space/technical-info/npsh-nh-nhr-fittings GHT, for 1/2, 5/8 or 3/4 hose, is 1.1/16-11.5 thread, as by NFPA 1963, "Standard for Fire Hose Connections", later by ANSI-ASME B1.20.7 common firehose threads: 1-14 NPSH, NPT 1.375-8 NH/NST 3/8", 1" 1.990-9 NH/NST 1.5" 2.515-8 NH/NST 2" 3.068-7.5 NH/NST 2.5" 3.623-6 NH/NST 3" 4.243-6 NH/NST 3.5" 5.010-4 NH/NST 4" 5.760-4 NH/NST 4.5" 6.260-4 NH/NST 5" 7.025-4 NH/NST 6" 1.035-14 NPSH/IPT 3/4" 1.295-11.5 NPSH/IPT 1" 1.818-11.5 NPSH/IPT 1.5" 2.352-11.5 NPSH/IPT 2" 2.841-8 NPSH/IPT 2.5" 3.470-8 NPSH/IPT 3" 3.970-8 NPSH/IPT 3.5" 4.470-8 NPSH/IPT 4" 4.970-8 NPSH/IPT 4.5" 5.560-8 NPSH/IPT 5" 6.620-8 NPSH/IPT 6" 2.96-11 US standard 2.1/2" hose, British Pipe BSP 3.00-8 US standard 2.1/2" hose, New York Corp NYC 3.03-8 US standard 2.1/2" hose, New York City FD FDNY 3.03-7.5 US standard 2.1/2" hose, Pacific Coast PCT 3.04-7 US standard 2.1/2" hose, Chicago Hose 3.00-7.5 US standard 2.1/2" hose, Chicago Fire Dept CFD 3.06-8 US standard 2.1/2" hose, Buffalo, NY 3.06-6 US standard 2.1/2" hose, Cincinnati, OH (new) 3.07-8 US standard 2.1/2" hose, Cleveland, OH 3.09-8 US standard 2.1/2" hose, Denver, CO 3.12-7.5 US standard 2.1/2" hose, Detroit, MI 3.07-8 US standard 2.1/2" hose, Omaha, NE 3.06-6 US standard 2.1/2" hose, Phoenix, AZ (old) 3.06-6 US standard 2.1/2" hose, Pittsburg, PA 3.25-6 US standard 2.1/2" hose, Salt Lake City, UT 3.00-8 US standard 2.1/2" hose, Toledo, OH 2.99-8 Canadian standard 2.1/2 hose, AMA, Alberta Mutual Aid 3.00-8 Canadian standard 2.1/2 hose, BCT, British Columbia 3.12-5 Canadian standard 2.1/2 hose, CSA, Canadian Standards Assoc. 3.03-7 Canadian standard 2.1/2 hose, QST, Province of Quebec Standard 3.25-6 Canadian standard 2.1/2 hose, WCT, Western Canada Fire Under 3.23-5 Canadian standard 2.1/2 hose, NOVA, Nova Scotia zone 1 3.03-7 Canadian standard 2.1/2 hose, QMT, Quebec-Montreal Combination M34x3 UNI 25 M56x4 UNI 40 M85x6 UNI 70
M10x1 standard in Europe, male on hose M8x1 less common standard, IKEA M12x1 another standard G3/8 most common wall-side and equipment-side outlet, male on wall/device G1/2 some equipment-side outlets, male on device https://www.bathroomsuppliesonline.com/userfiles/KartellbyLaufen5HoleBathShowerMixer3223350042821TD.PNG G3/4 mounting thread through-bulkhead on valves M27x1.5? M29x1.5 mounting thread through-bulkhead on faucets, shower handset holders with hose pullout M34x1.5 mounting thread through-bulkhead on faucets, valves natural gas connections: R1/2, G1/2 most common G3/4 happens M20x1.5 happens LPG connections: M9x0.75 hoses G3/8 G3/8 L (???) G1/4 G1/4 L G1/2 on stoves W21.8-14 left cylinders 5, 10, 33 kg; male on bottle W20-14 E21.8 ?? M22? ACME ?? tank nozzle connection, filling point (Germany, Belgium, Ireland) M33x? LPG filling point, euro (Spain, Portugal) M10x1.5 M14 Lovato M16x1.5 on cylinder: 3/4-14 NGT W28.8-14 DIN477 W28-14 1-11.5 NGT W20-14 on valves: 1.5/16-? ACME for filters W22.5-14 left female on valve .885-14 NGO left M14x1.5 male on valve 1/4-19 female on valve others: 3/4-16 UNF male on valve 1/4-19 NPT female on valve industrial gas cylinders, on cylinders: 5/8-18 UNF also CO2 1/2-14 NGT f on bottle, ASA 3/4-14 NGT f on bottle, ASA 1-11.5 NGT f on bottle, ASA 1" BS341 (25E) - ISO 11363-1 1.125-12 UNF 0.750-16 UNF PZ 27.8 3/8-18 NGT f on bottle, acetylene 1-14 UNS f on bottle, calibration gases 20mm, KS B 6214, v1 28mm, KS B 6214, v2 - W28-14? W19.8-14 DIN477 W28-14 freon 3/4-16 UNF f on bottle, medical, to CGA870 9/16-18 UNF f on bottle, medical oxygen, home filling, to CGA870 5/8-18 UNF f on bottle, medical oxygen 19.8, 28.8, 31.3 - DIN 477 on valves: 21-6 ACME CO2 bottles W23-14 W22.9-14; male on valve, O2 W22-14 left W21.8-14; H2 W22-14 Ar, CO2, NH3 W16-18 NH3 valve pressure relief device W26-14 W39-14 https://vdocuments.mx/cylinder-valve-inlet-connections-tekno-angle-thread-per-inch-tpi-specification.html 1/8-27 NGT gas bottle thread, female on bottle, taper 1:16 1/4-18 NGT gas bottle thread, female on bottle, taper 1:16 3/8-18 NGT gas bottle thread, female on bottle, taper 1:16 1/2-14 NGT gas bottle thread, female on bottle, taper 1:16; IS3224 type 1 size 1 3/4-14 NGT gas bottle thread, female on bottle, taper 1:16; IS3224 type 1 size 2 1-11.5 NGT gas bottle thread, female on bottle, taper 1:16; IS3224 type 1 size 3 W25.4-14 "1"BS"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 2; AS2473.2 "1.0-25AU" W26.194-14 "1.1/32"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 2, 3.5 turns oversize W26.987-14 "1.1/16"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 2, 7 turns oversize W27.781-14 "1.3/32"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 2, 10.5 turns oversize W28.574-14 "1.1/8"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 2, 14 turns oversize W18.16-14 "18T"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 1; AS2473.2 "0.715-18AU" W19.8-14 "17E"; gas bottle thread, DIN 477; IS3224 type 2 size 1; tapered 3:25 (see W19.2-14???); small cylinders; see also W28.8-14 W28.8-14 "25E"; gas bottle thread, DIN 477, IS3224 type 2 size 2; tapered 3:25; 10-50 liter cylinders; see also W19.8-14, W31.3-14 W31.3-14 "28E"; gas bottle thread, DIN 477, tapered 3:25; for acetylene; see also W19.8-14, W28.8-14 W31.75-11 "32T"; gas bottle thread, tapered 1:8, on smaller dia; IS3224 type 4 size 3 W21.2-14 "V1"; gas bottle thread, tapered 3:26, on larger dia; JIS 8246 W29.5-14 "V2", "V3"; gas bottle thread, tapered 3:26, on larger dia; JIS 8246 W40.3-14 "1.455""; gas bottle thread, tapered 3:26, on larger dia; JIS 8244 3/4-16 UNF gas bottle thread, parallel, female on bottle; JIS B 8246, IS 3224:2014 3/4-14 NPSM gas bottle thread, female on bottle, parallel; JIS B 8246, IS 3224:2014; equivalent to 3/4-14 NGS 1.1/8-12 UNF gas bottle thread, parallel, female on bottle; JIS B 8246, IS 3224:2014 M18x1.5 gas bottle thread, parallel; ISO 15245; see also M25x2, M30x2 M25x2 gas bottle thread, parallel; ISO 15245; see also M18x1.5, M30x2 M30x2 gas bottle thread, parallel; ISO 15245; see also M18x1.5, M25x2 https://www.bestmaterials.com/PDF_Files/propane-fitting-threads.pdf 3/8-18 NPT male on cylinder valve; vapor or liquid withdrawal .903-14 NGO left male on cylinder valve, CGA555 1.5/16 ACME male on cylinder valve, with CGA510 as "type I outlet" .885-14 NGO left female on cylinder valve, CGA510, "POL", most common US standard; with 1.5/16 ACME is "type I outlet" 5/8-18 male on cylinder valve, with male cone, CGA182, "SAE flare", "3/8 SAE" (3/8 tube) CGA791, "F.POL" M10x1 M12x1 M14x1 1/4 BSPP 3/8 BSPP 1/2 BSPP 1/4 NPT 1/2 UNF 3/4 UNF JIC common 7/16 UNF 5/8-18 UNF W20 M20 20/150 filling station connectors: ACME BE,CH,DE,IE,Luxembourgh,Chile bayonet ES,GB,NO,NL DISH "Italian type"; AT,Bosnia,BG,CH,CZ,DK,Estonia,FR,GR,HU,Croatia,IT,LT,LV,Macedonia,PT,PL,RO,Sweden,SK,Slovenia,TR,UA,Belarussia,Russia,Peru Euro ES,PT russian Russia,UA,LT,LV,Belarussia LPG: 1.3/4-6 ACME 2.1/4-6 ACME 3.1/4-6 ACME ACME small ?? cryo gases: Tr90x8 female, Tr89x8 male - EIGA couplers, on cylinders: W21.8-14 left Denmark, England, France, the Netherlands, Italy, Austria, Switzerland, Spain W20-14 left male on bottle; Italy M10x1 female on cylinder; Italy, Switzerland M14x1.5 Belgium, Denmark, Finland, Luxembourg, Norway, Austria, Portugal, Sweden, Switzerland, Italy 7/16-28 UNEF portable stove gas cartridges, male on bottle G3/8 left male on output of bottle valve G3/8 10tpi common due to lathes liking this feed 3/8-10 ACME on Myford lathes 7/16-10 ACME on Rivett lathes 5/16-10, 3/8-10, 1/2-10 square on early Hardinge lathes 5/16-10 square leadscrew, on early Hardinge lathes 3/8-10 ACME leadscrew, on Myford lathes 3/8-10 square leadscrew, on early Hardinge lathes 7/16-10 ACME leadscrew, on Rivett lathes 1/2-10 square leadscrew, on early Hardinge lathes
M10x1.25 on flareless tube fittings, for 4 mm tube M12x1.5 on flareless tube fittings, for 6 mm tube M14x1.5 on flareless tube fittings, for 8 mm tube M16x1.5 on flareless tube fittings, for 10 mm tube M18x1.5 on flareless tube fittings, for 12 mm tube M22x1.5 on flareless tube fittings, for 15 mm tube M28x1.5 on flareless tube fittings, for 20 mm tube M34x1.5 on flareless tube fittings, for 25 mm tube G1/8 on flareless tube fittings, for 4 mm tube G1/4 on flareless tube fittings, for 6 mm, 8 mm tube G3/8 on flareless tube fittings, for 10 mm tube G1/2 on flareless tube fittings, for 12 mm tube G5/8 on flareless tube fittings, for 15 mm tube G3/4 on flareless tube fittings, for 20 mm tube G1 on flareless tube fittings, for 25 mm tube
https://www.roton.com/products/ballscrews-and-ballnuts/engineering-data/ 3/8-8 1/2-2 5/8-5 3/4-2 1-4 1-3 1-2 1-1 1.1/2-2 1.1/2-1 freewheeling: https://www.roton.com/products/freewheeling-ballscrews-ballnuts/engineering-data/ 1/4x.188 5/16-8 9/16x.083 5/8x.188 3/4-4 1x.28 metric acme: https://www.mcmaster.com/metric-acme-nuts M10x2 M12x3 M16x4 M20x4 M26x5 M40x7 thread designations: https://www.swansongage.com/Customer-Content/www/CMS/files/Precision-Thread-Plain-Gage.pdf
M10x1 pressure check gauge thread, female on valve Vg8 pressure check gauge thread, female on valve M14x1.5 outlet thread, female on valve G1/4 outlet thread, female on valve M16x1.5 dip tube thread M16x1 dip tube thread W21.8-14 female on bottle M22x1.5 female on bottle M30x1.5 female on bottle M45x2 female on bottle
M18x1.5 female on bottle 5/8-18 UNF female on bottle (20MPa) 3/8-? M16x1.5 CO2 canisters, 88g, on eg. paintball guns 0.825-14 NGO pressure regulator output, male 1/8-BSP small tanks airsoft barrels: M14x1 M14x1 left paintball barrels: [ ref] 15/16-20 UNF Autococker 7/8-20 UNF A5/ProCarabine .835-20 UNF ATS (barrel) .760-56 ATS (Unisizer) 15/16-12 UNF DL (dual-leads) Impulse .860-14 Acme Phantom M24x2 Angel M22x1.5 Spyder .795 nonthread Blazer paintball/airsoft air/CO2 cylinders: 5/8-18 UNF-2B (SAE) paintball/airsoft 3/4-16 NPS Nitroduck air cylinders M16x1.5 CO2 canisters, 88g, on eg. paintball guns M18x1.5 88g disposable cylinders, male on cylinder [ ref] 1/2-14 BSP G1/2? on UK paintball CO2 cylinders, male on cylinder 3/4-14 NPSM SCUBA tanks, 200-bar 7/8-14 UNF-2B SCUBA tanks, 300-bar M18x1.5 ISO CP SCUBA tanks, Europe M25x2 ISO CP10 SCUBA tanks, Europe M25x2 DIN477 SCUBA tanks, Europe 3/4-14 NGS SCUBA tanks, Asia-Pacific, parallel
3/4-16 UNF most common for medical gases [ ref] 25E, W28.8-14 ISO, tapered 3:25, female in cylinder, common for medical gases; also 27.8-14, 25.8-14 17E, W19.2-14 ISO, tapered, female in cylinder, tapered, less common; also 17.4-14 18T ISO, tapered M18x1.5(?) M25x2(?) M30x? 3/4-14 NGT 1/2-14 NGT 1-11.5 NGT 1.1/8-12 UNF [ ref] cylinder tops: G3/4 standard CO2 bottles W21.8-14 BS341, DIN477 - O2, Ar, CO2 in Germany (W21.8-14 to/from G3/4 converters available) smaller bottles: [ ref] TR21x4 SodaStream, world except NZ/AU, male on bottle; converters easily available to W21.8-14, M18x1.5 G1/2?? SodaStream NZ/AU M10x1 disposable welding gas cylinders - 500g, 600g, 1000g M11x1 some disposable gas cylinders, e.g. CO2 3/8-24 UNF aquarium disposable cylinders, 16g 5/8-18 UNF aquarium disposable cylinders, 74g M16x1.5 aquarium disposable cylinders, 95g G1/2-14 CGA320 paintball tank refillable replaceable N2O canisters: 65mm long, 18.5mm dia, neck thread, silver nut cover refillable replaceable CO2 canisters, 8g: 65mm long, 18.5mm dia, neck thread, gold nut cover, contains 8 grams of CO2 CO2 canisters, 16g 88.4mm long, 22mm dia, throat outer dia 8.5mm refillable CO2 300g 240mm long, 60mm dia, thread G1/2 male refillable "cuvette" 150g 260mm long, 40mm dia, thread M18x2 female (wrench span 22mm) N2O cartridges also used in medicine, for cryosurgery, "CryoPen", 8g cartridges (up to 120 sec gas flow) (up to 1 pint of heavy whipping cream) cartridge size chart: [ ref] [ ref] CO2 N2O dia len vol neck dia/thread use !!! 8g 8/15 18.5(18?) 65(68?) 7mL 7.3mm, or 3/8-24 UNF CO2 (gold nut): soda, N2O (silver nut): whipping cream (500mL), cryosurgery ("Cryopen") 10g 12g 22g 18.6mm 82.5 15 plain, or 3/8-24 12g 18.9 82.3 14/15 plain air gun type, also "universal fit" 12g M16x1.5 disposable CO2 tanks 16g 18.7 64.5 10 3/8-24 MIL-C 601, inflators, SF6 refills (9grams) ! 16g 30 21.8mm 88.4 20 8.5mm?, or 3/8-24 CO2: food (5l kegs), airguns, bike tire inflator, aquariums 17g 31 25.4 94 28 3/8-24, 1/2-20 24g 25g 28g 52 21 161 38 3/8-24 33g 61 25.4 138 45 1/2-20 38g 71 30 138 62 1/2-20,5/8-18 38g 30 118.1mm 3/8-24 Leland Tactical Flotation Support System (TFSS) 55g 60g 65g 121 30 202 98 1/2-20 74g 5/8-18 aquariums 88g 165 35 200 97 1/2-20 88g 35 200 M16x1.5 paintball [ ref] 95g M16x1.5 aquariums ! 150g 40 260 M18x2 f, 22 spanner "cuvette", CO2 for restaurants/pubs ! 300g 60 240 G1/2 male 500g M10x1 welding gases, nonrefillable 600g M10x1 welding gases, nonrefillable 1000g M10x1 welding gases, nonrefillable necks: 0.287" (7.3mm) plain close to 9/32" 0.323" (8.2mm) plain close to 21/64" 0.338" (8.6mm) plain close to 11/32" 0.364" (9.2mm) plain close to 23/64" 3/8-24 UNF 9.53mm 1/2-20 UNF 12.7mm 5/8-18 UNF 15.9mm 3/4-16 UNF 19.1mm diameters: 375" 3/8" 9.525mm
https://www.thehosemaster.co.uk/bsp-pipe-threads M8x1 4mm tube: metric Norgren/Enots, metric WADE, Ni-plated brass M10x1 5mm tube: metric Norgren/Enots, metric WADE; 6mm tube: metric WADE, Ni-plated brass M11x1 6mm tube: metric Norgren/Enots M12x1 8mm tube: metric WADE, Ni-plated brass M13x1 8mm tube: metric Norgren/Enots M15x1 10mm tube: metric Norgren/Enots M16x1.5 10mm tube: metric WADE, Ni-plated brass M18x1.5 12mm tube: metric Norgren/Enots, Ni-plated brass; 15mm tube: metric WADE M20x1.5 16mm tube: metric WADE M22x1.5 15mm tube: metric Norgren/Enots, Ni-plated brass M24x1.5 16mm tube: metric Norgren/Enots M26x1.5 18mm tube: metric Norgren/Enots M27x1.5 20mm tube: metric WADE M30x1.5 22mm tube: metric Norgren/Enots, metric WADE G1/8 1/8" tube, 3/16" tube: imperial WADE G1/4 1/4" tube, 5/16" tube: imperial WADE G3/8 3/8" tube: imperial WADE G1/2 1/2" tube: imperial WADE G3/4 5/8" tube: imperial WADE G7/8 3/4" tube: imperial WADE R3/8-24 3/16" tube: imperial Norgren/Enots R7/16-24 1/4" tube: imperial Norgren/Enots R1/2-24 5/16" tube: imperial Norgren/Enots R9/16-24 3/8" tube: imperial Norgren/Enots R3/4-24 1/2" tube: imperial Norgren/Enots R7/8-20 5/8" tube: imperial Norgren/Enots (R=BSPT/tapered, G=BSPP/parallel, BSP==Whitworth) M8x1 compression fitting, 4mm tube: metric Norgren/Enots, metric WADE, Ni-plated brass M10x1 compression fitting, 5mm tube: metric Norgren/Enots, metric WADE; 6mm tube: metric WADE, Ni-plated brass M11x1 compression fitting, 6mm tube: metric Norgren/Enots M12x1 compression fitting, 8mm tube: metric WADE, Ni-plated brass M13x1 compression fitting, 8mm tube: metric Norgren/Enots M15x1 compression fitting, 10mm tube: metric Norgren/Enots M16x1.5 compression fitting, 10mm tube: metric WADE, Ni-plated brass M18x1.5 compression fitting, 12mm tube: metric Norgren/Enots, Ni-plated brass; 15mm tube: metric WADE M20x1.5 compression fitting, 16mm tube: metric WADE M22x1.5 compression fitting, 15mm tube: metric Norgren/Enots, Ni-plated brass M24x1.5 compression fitting, 16mm tube: metric Norgren/Enots M26x1.5 compression fitting, 18mm tube: metric Norgren/Enots M27x1.5 compression fitting, 20mm tube: metric WADE M30x1.5 compression fitting, 22mm tube: metric Norgren/Enots, metric WADE G1/8 compression fitting, 1/8" tube, 3/16" tube: imperial WADE G1/4 compression fitting, 1/4" tube, 5/16" tube: imperial WADE G3/8 compression fitting, 3/8" tube: imperial WADE G1/2 compression fitting, 1/2" tube: imperial WADE G3/4 compression fitting, 5/8" tube: imperial WADE G7/8 compression fitting, 3/4" tube: imperial WADE R3/8-24 compression fitting, 3/16" tube: imperial Norgren/Enots R7/16-24 compression fitting, 1/4" tube: imperial Norgren/Enots R1/2-24 compression fitting, 5/16" tube: imperial Norgren/Enots R9/16-24 compression fitting, 3/8" tube: imperial Norgren/Enots R3/4-24 compression fitting, 1/2" tube: imperial Norgren/Enots R7/8-20 compression fitting, 5/8" tube: imperial Norgren/Enots
https://www.hoseandfittingsetc.com/our-blog/bid/76568/Thread-Identification-for-Brake-Lines 3/8-24 UNF found on vehicle braking systems, brake master cylinder thread, SAE, very common, can be mismatched with M10x1 3/8-20 BSF found on vehicle braking systems 7/16-24 UNS found on vehicle braking systems, brake master cylinder thread, SAE, very common, can be mismatched with M11 7/16-20 UNF found on vehicle braking systems 1/2-20 UNF found on vehicle braking systems, brake master cylinder thread, SAE 9/16-18 UNF found on vehicle braking systems, brake master cylinder thread, SAE 9/16-20 UNF found on vehicle braking systems, brake master cylinder thread, SAE M9x1 found on vehicle braking systems M10x1 found on vehicle braking systems; brake master cylinder thread, metric (TN24), most common metric, can be mismatched with 3/8-24 M10x1.25 found on vehicle braking systems, brake master cylinder thread, metric M10x1.5 found on vehicle braking systems M11x1.25 found on vehicle braking systems, rare M11x1.5 brake master cylinder thread, metric (TN26), rare M12x1 found on vehicle braking systems, brake master cylinder thread, metric (TN27) M12x1.25 found on vehicle braking systems M12x1.5 found on vehicle braking systems, brake master cylinder thread, metric M13x1.5 brake master cylinder thread, metric (TN30) M14x1.5 found on vehicle braking systems 3/8-24 male will screw into M10x1 female, but not vice versa - use M10x1 male to test
cylinder tops: M17x1.5? M18x1.5 !M25x2 - most common on cylinders in Europe !3/4-14 NPSM - 3/4, 0.750-14NPSM, most common on cylinders in the US G3/4 - also 3/4 BSP, unused now, present on older equipment 7/8 UNF - also 0.875-14 UNF, on 3500psi (24MPa) steel cylinders W21.8-14, DIN 477 - G5/8, 14tpi - DIN-477 no.13 - air, "SCUBA DIN" G3/4, 14tpi - DIN-477 no.9 - oxygen rebreather oxygen tanks have female thread, welding and MH tanks are males BEWARE: M25 can be screwed about 6 turns into 3/4 NPSM, more if stronger user, can tear out and rocket off BEWARE: 3/4 NPS and 3/4 BSP are very similar but not identical, mismatch increases wear [ ref] regulator ports: 7/16" UNF - high pressure hose 3/8" UNF - most low pressure ports 1/2" UNF - some low pressure ports Type of Scuba Cylinder Service Pressure Valve (psi (bar)) PRD Argon Bottles 2015 (139) 3360 (232) Low Pressure Steels 2400+ (165) 4000 (276) Most Aluminums 3000 (207) 5000 (345) High Pressure Steels 3442 (237) 5250 (362) PRD (burst disc) required by law on all US pressure vessels. Fire-exposed cylinders usually fail due to strengh loss before PRD bursts. diving cylinder test pressure 1.5x working pressure (1.67 times in the US) parallel threads on bottles good for low-pressure (liquefied) nonhazardous gases [ ref] parallel threads on bottles illegal in some countries for toxic gases
M8x1 M16x1.5 5/8-18 UNF 7/8-14 UNF M28x1.5 G3/4 G1/4 M16x2 Vg8 W24.32-14 - male: Germany, Poland, others M14x1.5 - W21.8-14 - male: France, Egypt, Mexico, Israel; female: Italy W24.5-14 - female: Canada, USA, Brazil W22-14 - male: Japan W23-14 - female: Korea G1/2 - male: Peru, Colombia G5/8 - female: India, Argentina, GB, Vietnam, Indonesia; male: China G3/4 - male: Russia, Venezuela, Trinidad and Tobago M22x1.5 - male: Taiwan
https://www.technicke-soucasti.cz/pneumaticke-prvky-a-sroubeni/spojky-pro-automatizaci/sroubeni-s-prevlecnou-matici/ G1/8 hose 5mm, 6mm, 8mm, 10mm G1/4 hose 4mm, 6mm, 8mm, 10mm G3/8 hose 6mm, 8mm, 10mm, 12mm G1/2 hose 10mm, 12mm R1/8 hose 5mm, 6mm, 8mm, 10mm R1/4 hose 6mm, 8mm, 10mm R3/8 hose 6mm, 8mm, 10mm, 12mm R1/2 hose 8mm, 10mm, 12mm M5 hose 4mm, 5mm, 6mm(?) M6 hose 4mm, 5mm, 6mm M7x0.5 hose 5mm M7x0.75 hose 5mm M8x0.75 hose 6mm M10x1 hose 5mm M12x1 hose 8mm M14x1 hose 10mm M16x1 hose 12mm M20x1 hose 15mm
https://www.fasttech.com/forums/vapers/t/1209238/taps-and-dies 306 thread 601 thread 710 thread M5.5x0.5 Protank 3 Clearomizer M7x0.5 401 thread, also 402, 403 - same diameter, different length, also M401,M402,M403; male on battery, female on atomizer M7x0.5 510 thread, female on battery, male on atomizer; 10 threads, 5mm long; most common by far M8x0.75 901 thread, male on battery, female on atomizer M8x0.75 1xx thread, female on battery, male on atomizer M9x0.75 801 thread, male on battery, female on atomizer M10x1 (in some patent? male on battery) M12x0.5 eGo thread, male on battery, female on atomizer, battery with 510 thread inside M20x0.5 common mod threading: Stingray (not switch), Nemesis (not switch), Origin, etc. M20x1 common mod threading: Caravelsa, EA, Paps, etc M21x1 common mod threading: Chi You, King, Astro, Atom, Hammer, Oni, etc M19.5x0.5 "Nemesis mod" https://www.fasttech.com/product/1871707-510-adapter-for-nemesis-mod https://www.fasttech.com/category/3023/misc-accessories M5.5x0.5 Mini Protank, Protank M10x0.5 M10x1 external on 510 connectors for DIY batteries M11.5x0.5 panel nut on pushbuttons M12x0.5 common on chimneys, often with M5.5x0.5; eGo M14x0.5 on Orchid V6 RTA Rebuildable Tank Atomizer; on some chimneys M14x1 Acrylic Tank Section for e-Vape VS RTA M15x0.5 with M7x0.5; atomizer port on Taifun GT-T V2, female on battery M20x0.5 on MANY acrylic and steel tanks M20.5x1 top and bottom cap on Chi You Mechanical Mods M21x0.5 BT Big Tank RTA Atomizer tank, male on tank; firing lock ring on Nemesis Mechanical Mod M21x1 extension tube for LPG Mod, M21.5x0.5 iCig IWD WTA atomizer tank, male on tank atomizers: M13x0.5 on Goblin Mini RTA atomizers M14x1 on Flash e-Vape VS Styled RTA Rebuildable Tank Atomizer M15x0.5 on Bamboo RDA Rebuildable Dripping Atomizer M15x1 on Bubble RDA Rebuildable Dripping Atomizer M19x0.5 on CEO and Pyrro style RDA Rebuildable Dripping Atomizer M19.5x1 on Fat Man style RDA Rebuildable Dripping Atomizer M20x0.5 most common, on RDA and RTA atomizers M20x1 Aqua V2 and Legion style RDA M20.5x0.5 on IN'AX Mk2r styled RTA and Phimis Demon RDA M21x0.5 on Ubertoot UTA2 styled RTA M21.5x0.5 on N23 styled RDA M22x0.5 on HCigar HC Plus RTA M23x0.5 on Tsunami Style RDTA mods: M20x1 common M21x1 common M20.5x1 Origin, 4nine, Knight, Sir Lancelot, Penny, Castle, Fairy... M20.5x0.75 Smowell Moore Telescopic, Code Lock M20.5x0.5 Fortune, Ragnarok
3/8-16 UNC USA M10x1.5 elsewhere (also some gear shift knobs for cars) beer tap parts: 1.1/8-18 UNEF faucet coupler nut, US Beer Industry Standard M30x1.5 faucet coupler nut, metric G5/8 common on beer taps
M20x1.5 on some coffee machines: steam pipes, some Faema machines G3/8 on coffee machines: steam pipes, water pipes, most common
vertical rods ...clamps usually up to 13 mm
6mm 8mm my heater/stirrer 10mm 12mm ROTILABO; length 400,500,600,750,1000,1250,1500mm; Eisco Labs, with thread M10(x1.5) 12.5mm 1/2" (12.7mm) 13mm with M10x1.5 thread, less common than 12mm 15mm 16mm with M10x1.5 thread, less common 18mm unusual 20mm 25mm 26.9mm relatively common, heavy structural tubes 30mm 40mm 50mm horizontal clamp rods 9.4mm 9.525mm? 3/8"? tube holders, 15..32mm dia holes 20mm usual, 25mm some optical posts: 6mm "mini-series" - 4/40 or M3 screws, f on base, m on top 12mm metric 1/2" imperial, 12.7mm - 1/4-20 or M6 in base, 8-32 or M4 on top 1" imperial, 25.4mm 1.5" imperial, 38.1mm mounting bases: 1.25" dia - 1/4-20 M (7.6mm), M6 (7.6mm), 8-32 M (3.8mm), 1/4-20 F, M6 F, M4 F, 8-32 F 1.85" dia - 1/4-20 M 3"d x 1/2" th - 1/4-20 F, M6 F cage rods: 4mm for 16mm cage 6mm for 30mm, 60mm cage rails: 25,34, 66, 95mm square rails dovetail rails, 0.72" (18.2mm) wide lab thread adapters https://www.thorlabs.com/newgrouppage9.cfm?objectgroup_id=1745 8-32 M - 4-40 F 8-32 M - M4 F 8-32 M - M6 M 1/4-20 M - 8-32 F 1/4-20 M - 4-40 F 1/4-20 F - 8-32 F 1/4-20 F - round 0.4" 8-32 M - 4-40 M 1/4-20 M - 8-32 M 8-32 M - M4 M 1/4-20 M - M6 M 8-32 M - M6 M M4 M - M3 M M6 M - M4 M 1/4-20 F - 8-32 F M6 F - M4 F 8-32 F - round 0.28" 7.0mm C-bore #8 1/4-20 F - round 0.4" 10.2mm C-bore 1/4 M4 F - round 0.28" 7.0mm C-bore M4 M6 F - round 0.4" 10.2mm C-bore M6 8-32 M - 6-32 F 4-40 == M3 6-32 8-32 == M4 1/4-20 == M6 M3 M4 M6 hex keys, hex key thumbscrews 0.05" compat with 1.3mm hex sockets 5/64" compat with 2mm hex sockets for 8-32 1/8" 9/64" 3/16" 1.3mm 1.5mm 2mm 2.5mm 3mm 5mm
[ ref]
1/4-18 (M), 1/4-18 (F) - NPT
3/8-18 (M), 3/8-18 (F) - NPT
1/2-27 (F)
1/2-IPS (F)
9/16-24 (M)
5/8-18 (M)
5/8-24 (M)
5/8-27 (M)
11/16-24 (M)
11/16-27 (M)
3/4-11 (F)
3/4-27 (F)
13/16-20 (M)
13/16-24 (M), 13/16-24 (F)
13/16-27 "Delta(R)"
55/64-27 (F) common US size for female-threaded aerators, male on faucet
15/16-24 (M)
15/16-27 (M) common US size for male-threaded aerators, female on faucet
G1/2
G3/4
M15x1
M16x1 TT
M16.5x1 TT, "tom thumb" (maybe M16x1?), male on faucet
M18x1 TT(?), female on faucet
M18.5x1 TJ, "tiny junior" (maybe M18x1?), female on faucet
M19x1 JR HC, male on faucet,
M20x1 male or female on faucet
(M21x1)
M21.5x1 JR, "junior" (maybe M22x1?), male on faucet, common in Europe
M22x1
M22x1.5 "Moen(R)" (maybe M21.5x1.5?)
M24x1 (F) STD, "regular", usually female on faucet, on bidets
M28x1 bathtub spouts
https://www.amazon.com/Kissler-Faucet-Seat-Thread-Gauge/dp/B009VGFRBQ 6-32 8-32 10-32 10-24 7/16-27 Speakman 7/16-24 American Standard, 7/16-20 1/2-27 Indiana Brass, Kohler, Eljer 1/2-24 Sterling, Streamway, Briggs, Central Brass, 1/2-20 American Brass, American Standard, Crane, Price Pfister, Streamway, Eljer, Sayco 1/2-18 Union Brass 33/64-18 17/32-24 9/16-27 Indiana Brass 9/16-24 9/16-22 9/16-20 Harcraft 9/16-18 American Standard, Crane 5/8-27 Kohler 5/8-24 Central Brass 5/8-20 Union Brass, Briggs, Sayco, Gerber 5/8-18 Union Brass 21/32-18 Price Pfister 11/16-22 11/16-20 hoses: M8x1 M10x1 M12x1 M10x1 on door hinges M14 velcro sandpaper holder tool shaft, rotary wire brush tools, central nut on many angle grinders, common thermocouple ports on gas stoves, ovens, furnaces: M8x1 M9x1 M10x1 11/32-32 UNS (ASA) 7/16-28 UNEF engine glow plugs: M8x1 M9x1 M10x1 M10x1.25 M12x1.5
[ ref]
6-32
8-32
10-32
10-24
7/16-20
7/16-24
7/16-27
1/2-20
1/2-24
1/2-27
33/64-18
17/32-24
9/16-18
9/16-20
9/16-22
9/16-24
9/16-27
5/8-18
5/8-20
5/8-24
5/8-27
21/32-18
11/16-20
11/16-22
3/8" USA 9/16" USA G1/2 B EU, UK, Australia, Canada, Middle East, Africa G1/2 A EU, UK G3/4 UK
https://www.epa.gov/mvac/unique-fittings-label-colors-mvac-refrigerants 6/16-24 CFC-12, low-side port 6/16-24 Freeze 12, small cans 7/16-20 CFC-12, high-side port, 30-lb cylinders, small cans 8/16-16 ACME HFC-134a, 30lb cylinders, small cans 7/16-14 left Freeze 12, high side port 8/16-18 Freeze 12, low side port, 30-lb cylinders 8/16-13 FreeZone/HCFC blend Delta, high side port 9/16-18 FreeZone/HCFC blend Delta, low side port, 30-lb cylinders 6/16-24 left FreeZone/HCFC blend Delta, small cans 10/16-18 left R-414B/HCFC Blend Omicron/Hot Shot, high side port 10/16-18 R-414B/HCFC Blend Omicron/Hot Shot, low side port, 30-lb cylinders 5/16-24 R-414B/HCFC Blend Omicron/Hot Shot, small cans 0.305-32 R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, high side port 0.368-26 R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, low side port, 30-lb cylinders 6/16-24 left R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, high side port 7/16-20 left R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, low side port M14x1.25 left R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, small cans 8/16-20 left GHG-X5/Autofrost X5, high side port 9/16-18 left GHG-X5/Autofrost X5, low side port, 30-lb cylinders 0.305-32 left R-406A/GHG-12/GHG-X3/McCool, high side port 0.368-26 left R-406A/GHG-12/GHG-X3/McCool, low side port, 30-lb cylinders 8/16-20 left R-406A/GHG-12/GHG-X3/McCool, small cans; R-416A/FRIGC FR-12/HCFC Blend Beta, 30-lb cylinders 7/16-20 left R-416A/FRIGC FR-12/HCFC Blend Beta, small cans 7/16-14 SP34E, high side port 8/16-18 left SP34E, low side port, 30-lb cylinders 5/16-24 left SP34E, small cans 9/16-18 R-420A, high side port, small cans 9/16-18 left R-420A, low side port, 30-lb cylinders 8/16-16 left HFO-1234yf, 30-lb cylinders https://www.essentracomponents.com/en-us/news/product-resources/identifying-threads-and-connectors SAE flare: 45-deg (SAE J512) 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 7/8-14 1.1/16-14 SAE 45deg inverted flare 7/16-24 1/2-20 5/8-18 11/16-18 SAE pilot o-ring seat pilot male swivel 5/8-18 3/4-18 7/8-18 pilot female swivel 5/8-18 3/4-16 JIC thread: 37-deg flare, most common US fitting in Europe; up to 10,000 psi, UNF thread 5/16-24 UNF 3/8-24 UNF 7/16-20 UNF 1/2-20 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1.1/16-12 UN 1.3/16-12 UN 1.5/16-12 UN 1.5/8-12 UN 1.7/8-12 UN 2.1/2-12 UN ORFS: O-ring face seal 9/16-18 UNF 11/16-16 UNF 13/16-16 UNF 1-14 UNS 1.3/16-12 UN 1.7/16-12 UN 1.11/16-12 UN 2-12 UN JIS thread: tapered pipe, or 30-deg flare (female internal cone) 1/8-28 1/4-19 3/8-19 1/2-14 5/8-14 3/4-14 1-11 1.1/4-11 1.1/2-11 2-11 2.1/211 3-11 Komatsu 30-deg flange: metric thread, almost only on Komatsu equipment M12,14,16,18,20,22,24,30,33,36,42x1.5 Metric French GAZ 24deg: 24deg seat, metric thread M20x1.5 13.25mm tube M24x1.5 16.75mm tube M30x1.5 21.25mm tube M36x1.5 26.75mm tube M45x1.5 33.50mm tube M52x1.5 42.25mm tube M58x2 48.25mm tube Metric French millimetric: 24deg seat M12x1 6mm tube M14x1.5 8mm tube M16x1.5 10mm tube M18x1.5 12mm tube M20x1.5 14mm tube M22x1.5 15mm tube M24x1.5 16mm tube M27x1.5 18/20mm tube M30x1.5 22mm tube M33x1.5 25mm tube M36x1.5 28mm tube M39x1.5 30mm tube M42x1.5 32mm tube M45x1.5 35mm tube M48x1.5 38mm tube M52x1.5 40mm tube M54x2 45mm tube DIN: metric thread, 24deg cone or o-ring M12x1.5 6mm tube (light) M14x1.5 8mm tube (light), 6mm tube (heavy) M16x1.5 10mm tube (light), 8mm tube (heavy) M18x1.5 12mm tube (light), 10mm tube (heavy) M20x1.5 12mm tube (heavy) M22x1.5 15mm tube (light), 14mm tube (heavy) M24x1.5 16mm tube (heavy) M26x1.5 18mm tube (light) M30x2 22mm tube (light), 20mm tube (heavy) M36x2 28mm tube (light), 25mm tube (heavy) M42x2 30mm tube (heavy) M45x2 35mm tube (light) M52x2 42mm tube (light), 38mm tube (heavy) M12x1.5 tube coupling, DIN metric, 24deg cone or o-ring, 6mm tube (light) M12x1.5 tube coupling, Komatsu equipment, 30-deg cone M14x1.5 tube coupling, DIN metric, 24deg cone or o-ring, 8mm tube (light), 6mm tube (heavy) M14x1.5 tube coupling, Komatsu equipment, 30-deg cone M16x1.5 tube coupling, DIN metric, 24deg cone or o-ring,10mm tube (light), 8mm tube (heavy) M16x1.5 tube coupling, Komatsu equipment, 30-deg cone M18x1.5 tube coupling, DIN metric, 24deg cone or o-ring,12mm tube (light), 10mm tube (heavy) M18x1.5 tube coupling, Komatsu equipment, 30-deg cone M20x1.5 tube coupling, DIN metric, 24deg cone or o-ring, 12mm tube (heavy) M20x1.5 tube coupling, French GAZ 24-deg seat, 13.25mm tube M20x1.5 tube coupling, Komatsu equipment, 30-deg cone M22x1.5 tube coupling, DIN metric, 24deg cone or o-ring,15mm tube (light), 14mm tube (heavy) M22x1.5 tube coupling, Komatsu equipment, 30-deg cone M24x1.5 tube coupling, DIN metric, 24deg cone or o-ring, 16mm tube (heavy) M24x1.5 tube coupling, French GAZ 24-deg seat, 16.75mm tube M24x1.5 tube coupling, Komatsu equipment, 30-deg cone M26x1.5 tube coupling, DIN metric, 24deg cone or o-ring,18mm tube (light) M27x1.5 tube coupling, French millimetric 24-deg seat, 20mm tube M30x1.5 tube coupling, French GAZ 24-deg seat, 21.25mm tube M30x1.5 tube coupling, French millimetric 24-deg seat, 22mm tube M30x1.5 tube coupling, Komatsu equipment, 30-deg cone M30x2 tube coupling, DIN metric, 24deg cone or o-ring,22mm tube (light), 20mm tube (heavy) M33x1.5 tube coupling, French millimetric 24-deg seat, 25mm tube M33x1.5 tube coupling, Komatsu equipment, 30-deg cone M36x1.5 tube coupling, French GAZ 24-deg seat, 26.75mm tube M36x1.5 tube coupling, French millimetric 24-deg seat, 28mm tube M36x1.5 tube coupling, Komatsu equipment, 30-deg cone M36x2 tube coupling, DIN metric, 24deg cone or o-ring,28mm tube (light), 25mm tube (heavy) M39x1.5 tube coupling, French millimetric 24-deg seat, 30mm tube M42x1.5 tube coupling, Komatsu equipment, 30-deg cone M42x2 tube coupling, DIN metric, 24deg cone or o-ring, 30mm tube (heavy) M45x1.5 tube coupling, French GAZ 24-deg seat, 33.50mm tube M45x1.5 tube coupling, French millimetric 24-deg seat, 35mm tube M45x2 tube coupling, DIN metric, 24deg cone or o-ring,35mm tube (light) M52x1.5 tube coupling, French GAZ 24-deg seat, 42.25mm tube M52x2 tube coupling, DIN metric, 24deg cone or o-ring,42mm tube (light), 38mm tube (heavy) 1/8-28 tube coupling, JIS thread, tapered or 30-deg female internal cone 1/4-19 tube coupling, JIS thread, tapered or 30-deg female internal cone 5/16-24 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 5/16-24 tube coupling, SAE 45-deg flare (SAE J512) 3/8-24 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 3/8-24 tube coupling, SAE 45-deg flare (SAE J512) 3/8-19 tube coupling, JIS thread, tapered or 30-deg female internal cone 7/16-24 tube coupling, SAE 45-deg inverted flare 7/16-20 tube coupling, SAE 45-deg flare (SAE J512) 7/16-20 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1/2-20 tube coupling, SAE 45-deg flare (SAE J512), SAE 45-deg inverted flare 1/2-20 tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1/2-14 tube coupling, JIS thread, tapered or 30-deg female internal cone 9/16-18 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 9/16-18 UNF tube coupling, ORFS (O-ring face seal) 5/8-18 tube coupling, SAE 45-deg flare (SAE J512), SAE 45-deg inverted flare 5/8-18 tube coupling, SAE pilot o-ring seat, male and female swivel 5/8-14 tube coupling, JIS thread, tapered or 30-deg female internal cone 11/16-18 tube coupling, SAE 45-deg inverted flare 11/16-16 UNF tube coupling, ORFS (O-ring face seal) 3/4-18 tube coupling, SAE pilot o-ring seat, male swivel 3/4-16 tube coupling, SAE 45-deg flare (SAE J512) 3/4-16 tube coupling, SAE pilot o-ring seat, female swivel 3/4-16 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 3/4-14 tube coupling, JIS thread, tapered or 30-deg female internal cone 13/16-16 UNF tube coupling, ORFS (O-ring face seal) 7/8-18 tube coupling, SAE pilot o-ring seat, male swivel 7/8-14 tube coupling, SAE 45-deg flare (SAE J512) 7/8-14 UNF tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1-14 UNS tube coupling, ORFS (O-ring face seal) 1-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 1.1/16-14 tube coupling, SAE 45-deg flare (SAE J512) 1.1/16-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1.3/16-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1.3/16-12 UN tube coupling, ORFS (O-ring face seal) 1.1/4-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 1.5/16-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1.7/16-12 UN tube coupling, ORFS (O-ring face seal) 1.1/2-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 1.5/8-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 1.11/16-12 UN tube coupling, ORFS (O-ring face seal) 1.7/8-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 2-12 UN tube coupling, ORFS (O-ring face seal) 2-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 2.1/2-12 UN tube coupling, JIC (SAE J514, ISO 8434-2), 37-deg flare, most common US fitting in Europe 2.1/2-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 3-11 tube coupling, JIS thread, tapered or 30-deg female internal cone 5/16-24 car air conditioning refrigerant coupling, US EPA standard, R-414B/HCFC Blend Omicron/Hot Shot, small cans 5/16-24 left car air conditioning refrigerant coupling, US EPA standard, SP34E, small cans 6/16-24 car air conditioning refrigerant coupling, US EPA standard, CFC-12, low-side port; Freeze 12, small cans 6/16-24 left car air conditioning refrigerant coupling, US EPA standard, FreeZone/HCFC blend Delta, small cans; R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, high side port 7/16-20 car air conditioning refrigerant coupling, US EPA standard, CFC-12, high-side port, 30-lb cylinders, small cans 7/16-20 left car air conditioning refrigerant coupling, US EPA standard, R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, low side port; R-416A/FRIGC FR-12/HCFC Blend Beta, small cans 7/16-14 car air conditioning refrigerant coupling, US EPA standard, SP34E, high side port 7/16-14 left car air conditioning refrigerant coupling, US EPA standard, Freeze 12, high side port 8/16-20 left car air conditioning refrigerant coupling, US EPA standard, GHG-X5/Autofrost X5, high side port; R-406A/GHG-12/GHG-X3/McCool, small cans; R-416A/FRIGC FR-12/HCFC Blend Beta, 30-lb cylinders 8/16-18 car air conditioning refrigerant coupling, US EPA standard, Freeze 12, low side port, 30-lb cylinders 8/16-18 left car air conditioning refrigerant coupling, US EPA standard, SP34E, low side port, 30-lb cylinders 8/16-16 ACME car air conditioning refrigerant coupling, US EPA standard, HFC-134a, 30lb cylinders, small cans 8/16-16 left car air conditioning refrigerant coupling, US EPA standard, HFO-1234yf, 30-lb cylinders 8/16-13 car air conditioning refrigerant coupling, US EPA standard, FreeZone/HCFC blend Delta, high side port 9/16-18 car air conditioning refrigerant coupling, US EPA standard, FreeZone/HCFC blend Delta, low side port, 30-lb cylinders; R-420A, high side port, small cans 9/16-18 left car air conditioning refrigerant coupling, US EPA standard, GHG-X5/Autofrost X5, low side port, 30-lb cylinders; R-420A, low side port, 30-lb cylinders 10/16-18 left car air conditioning refrigerant coupling, US EPA standard, R-414B/HCFC Blend Omicron/Hot Shot, high side port 10/16-18 car air conditioning refrigerant coupling, US EPA standard, R-414B/HCFC Blend Omicron/Hot Shot, low side port, 30-lb cylinders 0.305-32 car air conditioning refrigerant coupling, US EPA standard, R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, high side port 0.305-32 left car air conditioning refrigerant coupling, US EPA standard, R-406A/GHG-12/GHG-X3/McCool, high side port 0.368-26 car air conditioning refrigerant coupling, US EPA standard, R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, low side port, 30-lb cylinders 0.368-26 left car air conditioning refrigerant coupling, US EPA standard, R-406A/GHG-12/GHG-X3/McCool, low side port, 30-lb cylinders M14x1.25 left car air conditioning refrigerant coupling, US EPA standard, R-414A/GHG-X4/HCFC Blend Xi/McCool Chill It, small cans https://www.hydraulicsdirect.com/Fitting-Thread-Chart-s/1934.htm NPT and NPTS commonly in 1/16th inch - "dash size" 32 equals 2" or 32/16" metric 60deg cone, DIN 7631; common in hydraulic systems, female cone on male M12x1.5 6mm tube M14x1.5 8mm tube M16x1.5 10mm tube M18x1.5 12mm tube M22x1.5 15mm tube M26x1.5 18mm tube M30x1.5 22mm tube M38x1.5 28mm tube M45x1.5 35mm tube M52x1.5 42mm tube Metric Tube Compression (DIN 2353 24deg Cone), bite-type ferrule, female cone on male M12x1.5 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M24x1.5 M26x1.5 M30x2 M36x2 M42x2 M45x2 M52x2 JIS-300 flare NPT 1/8 NPT 13/32-27 1/4 NPT 17/32-18 3/8 NPT 11/16-14 1/2 NPT 27/32-14 3/4 NPT 1.1/16-14 1 NPT 1.5/16-11.5 1.1/4 NPT 1.21/32-11.5 1.1/2 NPT 1.29/32-11.5 2 NPT 2.3/8-11.5 NPT 1/8 13/32-27 (M10.32x0.941) NPT 1/4 17/32-18 (M13.49x1.41) NPT 3/8 11/16-14 (M17.46x1.81) NPT 1/2 27/32-14 (M21.43x1.81) NPT 3/4 1.1/16-14 (M26.99x1.81) NPT 1 1.5/16-11.5 (M33.34x2.21) NPT 1.1/4 1.21/32-11.5 (M42.07x2.21) NPT 1.1/2 1.29/32-11.5 (M48.42x2.21) NPT 2 2.3/8-11.5 (M60.325x2.21) G1/8 3/8-28 (W9.525x0.907) G1/4 33/64-19 (W13.10x1.34) G3/8 21/32-19 (W16.67x1.34) G1/2 13/16-14 (W20.64x1.81) G5/8 7/8-14 (W22.23x1.81) G3/4 1.1/32-14 (W26.19x1.81) G1 1.5/16-11 (W33.34x2.31) G1.1/4 1.21/32-11 (W42.07x2.31) G1.1/2 1.7/8-11 (W47.63x2.31) G2 2.11/32-11 (W59.53x2.31)
SAE J514, JIC 37deg flare (male on male) 1/8 5/16-24 3/16 3/8-24 1/4 7/16-20 5/16 1/2-20 3/8 9/16-18 1/2 3/4-16 5/8 7/8-14 3/4 1.1/16-12 7/8 1.3/16-12 1 1.5/16-12 1.1/4 1.5/8-12 1.1/2 1.7/8-12 2 2.1/2-12 5/16-24 tube coupling, 1/8 ("-2"), SAE J514, JIC 37deg flare (male on male) 3/8-24 tube coupling, 3/16 ("-3"), SAE J514, JIC 37deg flare (male on male) 7/16-20 tube coupling, 1/4 ("-4"), SAE J514, JIC 37deg flare (male on male) 1/2-20 tube coupling, 5/16 ("-5"), SAE J514, JIC 37deg flare (male on male) 9/16-18 tube coupling, 3/8 ("-6"), SAE J514, JIC 37deg flare (male on male) 3/4-16 tube coupling, 1/2 ("-8"), SAE J514, JIC 37deg flare (male on male) 7/8-14 tube coupling, 5/8 ("-10"), SAE J514, JIC 37deg flare (male on male) 1.1/16-12 tube coupling, 3/4 ("-12"), SAE J514, JIC 37deg flare (male on male) 1.3/16-12 tube coupling, 7/8 ("-14"), SAE J514, JIC 37deg flare (male on male) 1.5/16-12 tube coupling, 1 ("-16"), SAE J514, JIC 37deg flare (male on male) 1.5/8-12 tube coupling, 1.1/4 ("-20"), SAE J514, JIC 37deg flare (male on male) 1.7/8-12 tube coupling, 1.1/2 ("-24"), SAE J514, JIC 37deg flare (male on male) 2.1/2-12 tube coupling, 2 ("-32"), SAE J514, JIC 37deg flare (male on male) SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 5/16-24 tube coupling, 1/8 ("-2"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 3/8-24 tube coupling, 3/16 ("-3"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 7/16-20 tube coupling, 1/4 ("-4"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1/2-20 tube coupling, 5/16 ("-5"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 9/16-18 tube coupling, 3/8 ("-6"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 3/4-16 tube coupling, 1/2 ("-8"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 7/8-14 tube coupling, 5/8 ("-10"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1.1/16-12 tube coupling, 3/4 ("-12"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1.3/16-12 tube coupling, 7/8 ("-14"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1.5/16-12 tube coupling, 1 ("-16"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1.5/8-12 tube coupling, 1.1/4 ("-20"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 1.7/8-12 tube coupling, 1.1/2 ("-24"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) 2.1/2-12 tube coupling, 2 ("-32"), SAE straight thread O-ring, O-ring boss (J1926-1, ISO 11296-1) O-ring face seal (ORFS, SAE J1453) 9/16-18 UNF tube coupling, 1/4 ("-4"), O-ring face seal (ORFS, SAE J1453) 11/16-16 UNF tube coupling, 3/8 ("-6"), O-ring face seal (ORFS, SAE J1453) 13/16-16 UNF tube coupling, 1/2 ("-8"), O-ring face seal (ORFS, SAE J1453) 1-14 UNS tube coupling, 5/8 ("-10"), O-ring face seal (ORFS, SAE J1453) 1.3/16-12 UN tube coupling, 3/4 ("-12"), O-ring face seal (ORFS, SAE J1453) 1.7/16-12 UN tube coupling, 1 ("-16"), O-ring face seal (ORFS, SAE J1453) 1.11/16-12 UN tube coupling, 1.1/4 ("-20"), O-ring face seal (ORFS, SAE J1453) 2-12 UN tube coupling, 1.1/2 ("-24"), O-ring face seal (ORFS, SAE J1453) SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 5/16-28 tube coupling, 1/8 ("-2"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 3/8-24 tube coupling, 3/16 ("-3"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 7/16-24 tube coupling, 1/4 ("-4"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 1/2-20 tube coupling, 5/16 ("-5"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 5/8-18 tube coupling, 3/8 ("-6"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 11/16-18 tube coupling, 7/16 ("-7"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 3/4-18 tube coupling, 1/2 ("-8"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 7/8-18 tube coupling, 5/8 ("-10"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars 1.1/16-16 tube coupling, 3/4 ("-12"), SAE inverted flare (SAE J512, 45 deg female on male, 42deg male on female), common in cars flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 5/16-24 tube coupling, 1/8 ("-2"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 3/8-24 tube coupling, 3/16 ("-3"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 7/16-20 tube coupling, 1/4 ("-4"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1/2-20 tube coupling, 5/16 ("-5"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 9/16-18 tube coupling, 3/8 ("-6"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 3/4-16 tube coupling, 1/2 ("-8"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 7/8-14 tube coupling, 5/8 ("-10"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1.1/16-12 tube coupling, 3/4 ("-12"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1.3/16-12 tube coupling, 7/8 ("-14"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1.5/16-12 tube coupling, 1 ("-16"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1.5/8-12 tube coupling, 1.1/4 ("-20"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 1.7/8-12 tube coupling, 1.1/2 ("-24"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) 2.1/2-12 tube coupling, 2 ("-32"), flareless compression (SAE J514, 24deg female flare on male, bite-type ferrule) O-ring pilot threads, common in automotive and commercial air conditioning 5/8-18 tube coupling, 3/8 ("-6"), male or female pilot, O-ring pilot threads, common in automotive and commercial air conditioning 3/4-18 tube coupling, 1/2 ("-8"), male pilot, O-ring pilot threads, common in automotive and commercial air conditioning 3/4-16 tube coupling, 1/2 ("-8"), female pilot, O-ring pilot threads, common in automotive and commercial air conditioning 7/8-18 tube coupling, 5/8 ("-10"), male pilot, O-ring pilot threads, common in automotive and commercial air conditioning 7/8-14 tube coupling, 5/8 ("-10"), female pilot, O-ring pilot threads, common in automotive and commercial air conditioning 1.1/16-16 tube coupling, 3/4 ("-12"), male pilot, O-ring pilot threads, common in automotive and commercial air conditioning 1.1/16-14 tube coupling, 3/4 ("-12"), female pilot, O-ring pilot threads, common in automotive and commercial air conditioning flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M8x1 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M10x1 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M12x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M14x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M16x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M18x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M20x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M22x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M24x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M26x1.5 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M27x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M33x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M36x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M42x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M45x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female M48x2 tube coupling, flat face port with metric threads (ISO 9974-1), seal between male end and flat face in female metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M8x1 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M10x1 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M12x1.5 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M14x1.5 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M16x1.5 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M18x1.5 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M22x1.5 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M27x2 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M33x2 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M42x2 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M48x2 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer M60x2 tube coupling, metric port and stud ends (ISO 6149), o-ring on male, seal between male base and female top chamfer metric 60-deg cone, female cone on male, common in hydraulics M12x1.5 tube coupling, 6mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M14x1.5 tube coupling, 8mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M16x1.5 tube coupling, 10mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M18x1.5 tube coupling, 12mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M22x1.5 tube coupling, 15mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M26x1.5 tube coupling, 18mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M30x1.5 tube coupling, 22mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M38x1.5 tube coupling, 28mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M45x1.5 tube coupling, 35mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics M52x1.5 tube coupling, 42mm tube, metric 60-deg cone (DIN 7631), female cone on male, common in hydraulics
https://www.hoseandfittingsetc.com/technical-info/tips/dash-size hose: INNER DIAMETER specified tube: OUTER DIAMETER specified all except transportation and refrigerant hoses: dash number is x/16th inch (-24 = 1.5", -4=1/4=4/16"...) transportation and refrigerant hoses inner dia (inch): -3 n/a -4 3/16 -5 1/4 -6 5/16 -8 13/32 -10 1/2 -12 5/8 -16 7/8 -20 1.1/8 -24 1.3/8 -32 1.13/16 -40 2.3/8 -48 3
https://irp-cdn.multiscreensite.com/62ccccd4/files/uploaded/identify-portsac49.pdf
https://www.pegasusautoracing.com/document.asp?DocID=TECH00096 https://www.pegasusautoracing.com/document.asp?DocID=TECH00095
https://www.concoa.com/cgachart.html CONCOA Precision Gas Controls Home | Resource Page CGA Fitting Reference A CGA fitting is the standardized system for the attachment of a compressed gas cylinder to the required regulator or transfer line. Examples of CGA fittings would be: CGA-580 for Non-flamable, Non-oxidizing gasses such as Nitrogen, Argon, or Helium. CGA-590 is used for compressed air CGA-326 is used for Nitrous Oxide. CGA-540 for oxygen - male on bottle CGA 510 - propane, large industrial acetylene - female on bottle CGA 300 - acetylene, large industrial, male on bottle CGA 520 - acetylene, "B" (40 ft3) male on bottle CGA 200 - acetylene, "MC" (10 ft3) male on bottle CGA 580 - Ar, N2, He CGA 350 - H2 CGA 320 - CO2, male on bottle
https://www.tedpella.com/company_html/Compressed_Gas_Cylinder_Outlet_Connections.htm default: male on bottle (otherwise INT), right-hand (otherwise LH)
There are approximately a dozen commonly used CGA-fittings, with others used for special purposes. https://www.concoa.com/cgachart.html INT == female on bottle CGA 110 0.3125-32 UNEF INT All Gases Small Cylinders CGA 170 9/16"-18 UNF INT Argon, Helium Non Corrosive, Small Cylinders CGA 180 5/8"-18 UNF INT All Gases Small Cylinders CGA 240 3/8"-18 NPT Ammonia Toxic CGA 296 0.803"-14 UNS INT Oxygen Mix > 23% Oxidizing Mixtures CGA 300 0.825"-14 NGO Ethyl Chloride Refrigerant CGA 320 0.825"-14 NGO Carbon Dioxide Non Flammable CGA 326 0.825"-14 NGO Air Oxidizer CGA 330 0.825"-14 NGO LH Hydrogen Chloride Toxic CGA 346 0.825"-14 NGO Air Oxidizer CGA 350 0.825"-14 NGO LH Hydrogen, Methane Flammable CGA 510 0.885"-14 NGO LH INT Propane Flammable CGA 540 0.903"-14 NGO Oxygen Oxidizer CGA 580 0.965"-14 NGO INT Argon, Nitrogen Inerts CGA 590 0.965"-14 NGO LM INT Air Oxidizer CGA 660 1.030"-14 NGO Hydrogen Sulphide Toxic CGA 679 1.030"-14 NGO LH Nitrogen High Pressure CGA 705 1.125"-14 UNS Ammonia Toxic CGA 020 .375-24 UNF 2A oxygen, "A fitting", up to 200 psig CGA 021 .375-24 UNF 2A LH fuel gases, "A fitting", up to 200 psig CGA 022 .5625-18 UNF oxygen, "B fitting", up to 200 psig CGA 023 .5625-18 UNF LH fuel gases, "B fitting", up to 200 psig CGA 024 .875-14 UNF oxygen, "C fitting", up to 200 psig CGA 025 .875-14 UNF LH fuel gases, "C fitting", up to 200 psig CGA 032 .625-18 UNF INT inert gases, "B fitting", up to 200 psig CGA 033 .625-18 UNF LH INT industrial air, water, "B fitting", up to 200 psig CGA 034 .875-14 UNF INT inert gases, "C fitting", up to 200 psig CGA 035 .875-14 UNF LH INT industrial air, water, "C fitting", up to 200 psig CGA 670 1.030"-?? 3/8-24 UNF gas bottle thread, CGA 020 (USA/Canada), male on bottle; oxygen, "A fitting", up to 200 psig 3/8-24 UNF left gas bottle thread, CGA 021 (USA/Canada), male on bottle; fuel gases, "A fitting", up to 200 psig .5625-18 UNF gas bottle thread, CGA 022 (USA/Canada), male on bottle; oxygen, "B fitting", up to 200 psig .5625-18 UNF left gas bottle thread, CGA 023 (USA/Canada), male on bottle; fuel gases, "B fitting", up to 200 psig 5/8-18 UNF gas bottle thread, CGA 032 (USA/Canada), female on bottle; inert gases, "B fitting", up to 200 psig 5/8-18 UNF left gas bottle thread, CGA 033 (USA/Canada), female on bottle; industrial air, water, "B fitting", up to 200 psig 7/8-14 UNF gas bottle thread, CGA 024 (USA/Canada), male on bottle; oxygen, "C fitting", up to 200 psig 7/8-14 UNF left gas bottle thread, CGA 025 (USA/Canada), male on bottle; fuel gases, "C fitting", up to 200 psig 7/8-14 UNF gas bottle thread, CGA 034 (USA/Canada), female on bottle; inert gases, "C fitting", up to 200 psig 7/8-14 UNF left gas bottle thread, CGA 035 (USA/Canada), female on bottle; industrial air, water, "C fitting", up to 200 psig 0.3125-32 UNEF gas bottle thread, CGA 110 (USA/Canada), female on bottle; small cylinders, all gases 9/16-18 UNF gas bottle thread, CGA 170 (USA/Canada), female on bottle; small cylinders, noncorrosive - argon, helium 5/8-18 UNF gas bottle thread, CGA 180 (USA/Canada), female on bottle; small cylinders, all gases 3/8-18 NPT gas bottle thread, CGA 240 (USA/Canada), male on bottle; toxic - ammonia 0.803-14 UNS gas bottle thread, CGA 296 (USA/Canada), female on bottle; oxidizing - oxygen mix above 23% 0.825-14 NGO gas bottle thread, CGA 300 (USA/Canada), male on bottle; refrigerant - ethyl chloride 0.825-14 NGO gas bottle thread, CGA 320 (USA/Canada), male on bottle; nonflammable - CO2 0.825-14 NGO gas bottle thread, CGA 326 (USA/Canada), male on bottle; oxidizer - air 0.825-14 NGO left gas bottle thread, CGA 330 (USA/Canada), male on bottle; toxic - hydrogen chloride 0.825-14 NGO gas bottle thread, CGA 346 (USA/Canada), male on bottle; oxidizer - air 0.825-14 NGO left gas bottle thread, CGA 350 (USA/Canada), male on bottle; flammable - hydrogen, methane 0.885-14 NGO left gas bottle thread, CGA 510 (USA/Canada), female on bottle; flammable - propane 0.903-14 NGO gas bottle thread, CGA 540 (USA/Canada), male on bottle; oxidizer - oxygen; common in oxygen systems 0.965-14 NGO gas bottle thread, CGA 580 (USA/Canada), female on bottle; inerts - argon, nitrogen 0.965-14 NGO left gas bottle thread, CGA 590 (USA/Canada), female on bottle; oxidizer - air 1.030-14 NGO gas bottle thread, CGA 660 (USA/Canada), male on bottle; toxic - hydrogen sulfide 1.030-14 NGO left gas bottle thread, CGA 679 (USA/Canada), male on bottle; high-pressure - nitrogen 1.1/8-14 UNS gas bottle thread, CGA 705 (USA/Canada), male on bottle; toxic - ammonia
IRAM 2539 No.1 3/4" BSP x 1/14" - INT Acetylene Flammable IRAM 2539 No.2 W 21.8 - 1 1/4 Oxygen, Sulphur Hexafluoride Various IRAM 2539 No.3 5/8" BSP - INT Argon, Nitrogen Non Flammable IRAM 2539 No.4 W 21.8 - 1/4 Ethane, Hydrogen Flammable IRAM 2539 No.5 3/8" BSP - INT Nitrous Oxide Oxidizer 3/4-14 BSP gas bottle thread, IRAM 2539 No.1 (Argentina), female on bottle; flammable - acetylene W21.8-14 gas bottle thread, IRAM 2539 No.2 (Argentina), male on bottle; various - oxygen, SF6 5/8-14 BSP gas bottle thread, IRAM 2539 No.3 (Argentina), female on bottle; nonflammable - argon, nitrogen W21.8-14 gas bottle thread, IRAM 2539 No.4 (Argentina), male on bottle; flammable - hydrogen, ethane 3/8-19 BSP gas bottle thread, IRAM 2539 No.5 (Argentina), female on bottle; oxidizer - nitrous oxide
Type 10 G 5/8" RH INT Argon, Helium, Oxygen -le 20,000 kPa Non Flammable Type 11 G 5/8" RH INT Extended nipple Oxygen -gt 20,000 kPa, -le 25,000 kPa Oxidizer Type 20 G 5/8" LH INT Acetylene, Hydrogen, Ethylene, Methane Flammable Type 21 0.885"-14 NGO LH INT LPG, Propane Flammable Type 30 0.860"-14 BSW RH EXT Carbon Dioxide, Nitrous Oxide Non Flammable / Oxidizer Type 31 G 5/8" Sulphur Hexafluoride, Phosgene, Methyl Bromide Chemical Gases Type 32 G 1/2" Ammonia, Sulphur Dioxide Toxic Type 33 G 1/4" Small cyls -lt 4.5l water capacity Non Toxic, Non Flammable Mixtures Type 34 G 3/4" R134a Refrigerant Type 40 G 5/8" LH EXT Ethylene Oxide Toxic Type 41 G 3/8" BSP LH EXT LPG, Propane Flammable Type 42 G 1/2" LH EXT Methylamine Toxic Type 43 0.825"-14 NGO LH EXT Hydrogen Chloride, Hydrogen Sulphide Toxic / Corrosive Type 44 G 3/8" BSP Calibration gas mixtures Toxic, Non Flammable Mixtures Type 50 24x2 Whit Nitrogen -le 20,000 kPa Inert Type 51 1.045"-14 NGO RH INT Nitrogen -gt 20,000 kPa Inert Type 60 27x2 Whit Air -le 20,000 kPa Non Flammable Type 61 0.825"-14 NGO Air -gt 20,000 kPa Non Flammable G5/8 gas bottle thread, AS 2473.2 Type 10 (Australia/NZ), female on bottle; nonflammable below 20 MPa - argon, helium, oxygen G5/8 gas bottle thread, AS 2473.2 Type 11 (Australia/NZ), female on bottle, extended nipple; oxidizer 20-25 MPa - oxygen G5/8 left gas bottle thread, AS 2473.2 Type 20 (Australia/NZ), female on bottle; flammable - acetylene, hydrogen, ethylene, methane 0.885-14 NGO left gas bottle thread, AS 2473.2 Type 21 (Australia/NZ), female on bottle; flammable - LPG, propane 0.860-14 BSW gas bottle thread, AS 2473.2 Type 30 (Australia/NZ), male on bottle; nonflammable/oxidizer - CO2, N2O G5/8 gas bottle thread, AS 2473.2 Type 31 (Australia/NZ), male on bottle; chemical gases - SF6, phosgene, methyl bromide G1/2 gas bottle thread, AS 2473.2 Type 32 (Australia/NZ), male on bottle; toxic - NH3, SO2 G1/4 gas bottle thread, AS 2473.2 Type 33 (Australia/NZ), male on bottle; nontoxic, nonflammable, small bottles below 4.5l water G3/4 gas bottle thread, AS 2473.2 Type 34 (Australia/NZ), male on bottle; refrigerant - R134a G5/8 left gas bottle thread, AS 2473.2 Type 40 (Australia/NZ), male on bottle; toxic - ethylene oxide G3/8 left gas bottle thread, AS 2473.2 Type 41 (Australia/NZ), male on bottle; flammable - LPG, propane G1/2 left gas bottle thread, AS 2473.2 Type 42 (Australia/NZ), male on bottle; toxic - methylamine 0.825-14 NGO left gas bottle thread, AS 2473.2 Type 43 (Australia/NZ), male on bottle; toxic/corrosive - HCl, H2S G3/8 gas bottle thread, AS 2473.2 Type 44 (Australia/NZ), male on bottle; toxic/nonflammable - calibration gases W24x2 gas bottle thread, AS 2473.2 Type 50 (Australia/NZ), male on bottle; inert to 20 MPa - nitrogen 1.045-14 NGO gas bottle thread, AS 2473.2 Type 51 (Australia/NZ), female on bottle; inert over 20 MPa - nitrogen W27x2 gas bottle thread, AS 2473.2 Type 60 (Australia/NZ), male on bottle; nonflammable to 20 MPa - air 0.825-14 NGO gas bottle thread, AS 2473.2 Type 61 (Australia/NZ), male on bottle; nonflammable over 20 MPa - air
ABNT 172-1 3/8"-18 NGT INT Ammonia Toxic ABNT 218-1 W 21.8-14 INT Air, Oxygen, Oxygen Mix >20% Oxidizer ABNT 218-2 W 21.8-14 LH INT Hydrogen, Methane Flammable ABNT 225-2 0.885"-14 NGO LH Acetylene, Butane Flammable ABNT 245-1 0.960"-14 NGO Argon, Helium, Nitrogen Inerts ABNT 245-1 0.960"-14 NGO Inert gases + Oxygen Mix -lt 20% Inerts ABNT 245-2 0.960"-14 NGO LH Sulphur Hexafluoride Non Flammable ABNT 262-1 1.035"-14 NGO INT Sulphur Dioxide, Chlorine Toxic ABNT 209-1 0.830"-14 NGO INT Carbon Dioxide Non Flammable ABNT 209-2 0.830"-14 NGO LH INT (Round Nipple) Carbon Monoxide, Phosphine, Silane Toxic, Flammable ABNT 209-4 0.830"-14 NGO LH INT (Flat Nipple) Hydrogen Chloride, Hydrogen Sulphide Toxic ABNT 166-1 G 3/8" A - ISO 228-1 Nitrous Oxide Oxidizer 3/8-18 NGT gas bottle thread, ABNT 172-1 (Brazil), female on bottle; toxic - ammonia W21.8-14 gas bottle thread, ABNT 218-1 (Brazil), female on bottle; oxidizer - air, oxygen, oxygen mix over 20% W21.8-14 left gas bottle thread, ABNT 218-2 (Brazil), female on bottle; flammable - hydrogen, methane 0.885-14 NGO left gas bottle thread, ABNT 225-2 (Brazil), male on bottle; flammable - acetylene, butane 0.960-14 NGO gas bottle thread, ABNT 245-1 (Brazil), male on bottle; inerts - Ar, He, N2 0.960-14 NGO gas bottle thread, ABNT 245-1 (Brazil), male on bottle; inerts - inert gases + oxygen below 20% 0.960-14 NGO left gas bottle thread, ABNT 245-2 (Brazil), male on bottle; nonflammable - SF6 1.035-14 NGO gas bottle thread, ABNT 262-1 (Brazil), female on bottle; toxic - SO2, Cl2 0.830-14 NGO gas bottle thread, ABNT 209-1 (Brazil), female on bottle; nonflammable - CO2 0.830-14 NGO left gas bottle thread, ABNT 209-2 (Brazil), female on bottle, round nipple; toxic, flammable - CO, PH3, SiH4 0.830-14 NGO left gas bottle thread, ABNT 209-4 (Brazil), female on bottle, flat nipple; toxic - HCl, H2S G1/8 A gas bottle thread, ABNT 166-1 (Brazil), male on bottle, ISO 228-1; oxidizer - N2O
NF B W 30 x 1.75 Industrial Air Oxidizer NF C SI 21.7 x 1.814 Argon, Helium, Nitrogen Inert Gases NF E SI 21.7 x 1.814 LH Hydrogen, Hydrogen Mix >4% Flammable NF F SI 22.94 x 1.814 INT Oxygen Oxidizer NF G SI 26 x 1.5 INT Nitrous Oxide Oxidizer NF H W 22.91 x 1.814 LH INT Acetylene Flammable NF J W 25.4 x 3.175 Chlorine Corrosive NF K W 27 x 2 Hydrogen Chloride Corrosive NF L W 27 x 2 Inert gases + Oxygen Mix > 21% Oxidizer NF M W 30 x 2 Inert gases + Oxygen Mix > 21% + CO2 -lt 7% Oxidizer NF P W 27 x 2 Nitric Oxide, Nitrogen Dioxide Oxidizer or Corrosive W30x1.75 gas bottle thread, AFNOR NF B (France), male on bottle; oxidizer - industrial air SI 21.7-14 gas bottle thread, AFNOR NF C (France), male on bottle; inert gases - Ar, He, N2 SI 21.7-14 left gas bottle thread, AFNOR NF E (France), male on bottle; flammable - H2, H2 mix over 4% SI 22.94-14 gas bottle thread, AFNOR NF F (France), female on bottle; oxidizer - oxygen SI 26x1.5 gas bottle thread, AFNOR NF G (France), female on bottle; oxidizer - N2O W22.91-14 left gas bottle thread, AFNOR NF H (France), female on bottle; flammable - acetylene W25.4-8 gas bottle thread, AFNOR NF J (France), male on bottle; corrosive - Cl2 W27x2 gas bottle thread, AFNOR NF K (France), male on bottle; corrosive - HCl W27x2 gas bottle thread, AFNOR NF L (France), male on bottle; oxidizer - inert + oxygen over 21% W30x2 gas bottle thread, AFNOR NF M (France), male on bottle; oxidizer - inert + oxygen over 21% + CO2 under 7% W27x2 gas bottle thread, AFNOR NF P (France), male on bottle; oxidizer or corrosive - N2O, NO2 gas bottle thread, ABNT 218-1 (Brazil), female on bottle;
DIN 477 No. 1 W 21.8 x 1/14" LH Hydrogen, Propane Flammable DIN 477 No. 2 W 21.8" x 1/14" LH Propane Flammable DIN 477 No. 3 Yoke Acetylene Flammable DIN 477 No. 3.1 M 24 x 2" LH Acetylene Flammable DIN 477 No. 5 W 1" x 1/8" LH Carbon Monoxide Toxic DIN 477 No. 6 W 21.8 x 1/14" Argon, Helium, Carbon Dioxide Various DIN 477 No. 7 G 5/8" Sulphur Dioxide Toxic DIN 477 No. 8 W 1" x 1/8" Boron Trichloride Toxic DIN 477 No. 9 G 3/4" Oxygen Oxidizer DIN 477 No. 10 W 24.32 x 1/14" RH Nitrogen Inerts DIN 477 No. 11 G 3/8" Nitrous Oxide (>3 l size) Oxidizer DIN 477 No. 12 G 3/4" INT Nitrous Oxide (-lt 3 l size) Oxidizer DIN 477 No. 13 G 5/8" INT Air Non Flammable DIN 477 No. 14 M 19 x 1.5 LH Mixtures Various W21.8-14 left gas bottle thread, DIN 477 No.1 (Germany, most Europe), male on bottle; flammable - hydrogen, propane W21.8-14 left gas bottle thread, DIN 477 No.2 (Germany, most Europe), male on bottle; flammable - propane yoke gas bottle thread, DIN 477 No.3 (Germany, most Europe), male on bottle; flammable - acetylene M24x2 left gas bottle thread, DIN 477 No.3.1 (Germany, most Europe), male on bottle; flammable - acetylene W1-8 left gas bottle thread, DIN 477 No.5 (Germany, most Europe), male on bottle; toxic - CO W21.8-14 gas bottle thread, DIN 477 No.6 (Germany, most Europe), male on bottle; various - Ar, He, CO2 G5/8 gas bottle thread, DIN 477 No.7 (Germany, most Europe), male on bottle; toxic - SO2 W1-8 gas bottle thread, DIN 477 No.8 (Germany, most Europe), male on bottle; toxic - BCl3 G3/4 gas bottle thread, DIN 477 No.9 (Germany, most Europe), male on bottle; oxidizer - oxygen W24.32-14 gas bottle thread, DIN 477 No.10 (Germany, most Europe), male on bottle; inerts - N2 G3/8 gas bottle thread, DIN 477 No.11 (Germany, most Europe), male on bottle; oxidizer - N2O over 3 liters G3/4 gas bottle thread, DIN 477 No.12 (Germany, most Europe), female on bottle; oxidizer - N2O to 3 liters G5/8 gas bottle thread, DIN 477 No.13 (Germany, most Europe), female on bottle; nonflammable - air M19x1.5 left gas bottle thread, DIN 477 No.14 (Germany, most Europe), male on bottle; various - mixtures
UNI 4405 W 20 x 1/14" LH Hydrogen Flammable UNI 4406 W 21.7 x 1/14" Carbon Dioxide, Oxygen Non Flammable / Oxidizer UNI 4407 W 30 x 1/14" Ammonia Toxic UNI 4408 W 1" x 1/8" Chlorine Toxic UNI 4409 W 21.7 x 1/14" Nitrogen Inert UNI 4410 W 30 x 1/14" Air Non Flammable UNI 4411 W 22.9 x 1/14" Acetylene Flammable UNI 4412 W 24.5 x 1/14" Argon, Helium Inerts UNI 9097 G 3/8" EXT Nitrous Oxide Oxidizer W20-14 left gas bottle thread, UNI 4405 (Italy), male on bottle; flammable - H2 W21.7-14 gas bottle thread, UNI 4406 (Italy), male on bottle; nonflammable/oxidizer - CO2, oxygen W30-14 gas bottle thread, UNI 4407 (Italy), male on bottle; toxic - ammonia W1-8 gas bottle thread, UNI 4408 (Italy), male on bottle; toxic - Cl2 W21.7-14 gas bottle thread, UNI 4409 (Italy), male on bottle; inert - N2 W30-14 gas bottle thread, UNI 4410 (Italy), male on bottle; nonflammable - air W22.9-14 gas bottle thread, UNI 4411 (Italy), male on bottle; flammable - acetylene W24.5-14 gas bottle thread, UNI 4412 (Italy), male on bottle; inerts - Ar, He G3/8 gas bottle thread, UNI 9097 (Italy), male on bottle; oxidizer - N2O gas bottle thread, UNI 4405 (Italy), male on bottle;
LU 0 M 19 x 1.5 LH Flammable Mixtures Flammable Mixtures LU 1 W 21.8 - 1/14" LH Hydrogen, Methane Flammable LU 4 W 25.4 x 3.175" LH Hydrogen Cyanide Toxic RI 2 G 22.91 x 1.814" RH Oxygen Oxidizer RU 1 W 21.8 - 1/14" Ammonia, Carbon Dioxide Refigerants RU 3 W 24.32 - 1/14" Argon, Helium, Nitrogen Inerts RU 4 W 25.4 x 3.175" RH Chlorine, Hydrogen Chloride, Sulphur Dioxide Toxic RU 6 W 28.81 x 1.814" RH Air Oxidizer M19x1.5 left gas bottle thread, NEN 3268 LU 0 (Netherlands), male on bottle; flammable mixtures W21.8-14 left gas bottle thread, NEN 3268 LU 1 (Netherlands), male on bottle; flammable - H2, methane W25.4-8 left gas bottle thread, NEN 3268 LU 4 (Netherlands), male on bottle; toxic - HCN G22.91-14 gas bottle thread, NEN 3268 RI 2 (Netherlands), male on bottle; oxidizer - oxygen W21.8-14 gas bottle thread, NEN 3268 RU 1 (Netherlands), male on bottle; refrigerants - NH3, CO2 W24.32-14 gas bottle thread, NEN 3268 RU 3 (Netherlands), male on bottle; inerts - Ar, He, N2 W25.4-8 gas bottle thread, NEN 3268 RU 4 (Netherlands), male on bottle; toxic - Cl2, HCl, SO2 W28.81-14 gas bottle thread, NEN 3268 RU 6 (Netherlands), male on bottle; oxidizer - air
TIPO B M 30 x 1.75 Air Non Flammable TIPO C W 21.7 x 1/14" Argon, Helium, Nitrogen Inerts TIPO E W 21.7 x 1/14" LH Hydrogen, Methane, Propane Flammable TIPO F G 5/8" INT Oxygen Oxidizer TIPO G M 26 x 1.5 INT Oxygen Mix > 23% Oxidizing Mixtures TIPO H G 5/8" LH INT Acetylene Flammable TIPO J W 1" Hydrogen Chloride, Hydrogen Bromide Toxic and Corrosive TIPO M M 19 x 1.5 LH Calibration Gas Mixtures Mixtures TIPO T W 31.75 x 1/7" 237 Chlorine Drum Tanks Toxic or Corrosive TIPO U G 3/8" Nitrous Oxide Oxidizer M30x1.75 gas bottle thread, ITC EP6 TIPO B (Spain), male on bottle; nonflammable - air W21.7-14 gas bottle thread, ITC EP6 TIPO C (Spain), male on bottle; inerts - Ar, He, N2 W21.7-14 left gas bottle thread, ITC EP6 TIPO E (Spain), male on bottle; flammable - H2, methane, propane G5/8 gas bottle thread, ITC EP6 TIPO F (Spain), female on bottle; oxidizer - oxygen M26x15 gas bottle thread, ITC EP6 TIPO G (Spain), female on bottle; oxidizer - oxygen over 23% G5/8 left gas bottle thread, ITC EP6 TIPO H (Spain), female on bottle; flammable - acetylene W1 gas bottle thread, ITC EP6 TIPO J (Spain), male on bottle; toxic and corrosive - HCl, HBr M19x1.5 left gas bottle thread, ITC EP6 TIPO M (Spain), male on bottle; mixtures - calibration gases W31.75-7 gas bottle thread, ITC EP6 TIPO T (Spain), male on bottle; toxic or corrosive - chlorine drum tanks G3/8 gas bottle thread, ITC EP6 TIPO U (Spain), male on bottle; oxidizer - N2O
BS 341 No. 2 G 5/8" LH Acetylene Flammable BS 341 No. 3 G 5/8" INT Air, Argon, Neon, Nitrogen Inerts BS 341 No. 3 G 5/8" INT Oxygen Oxidizer BS 341 No. 4 G 5/8" LH INT Acetylene, Hydrogen Flammable BS 341 No. 4 G 5/8" LH INT Carbon Monoxide, Methane, Natural Gas Flammable BS 341 No. 6 G 5/8" Chlorine, Hydrogen Chloride Toxic BS 341 No. 7 G 5/8" LH Flammable Refrigerants Flammable Refrigerants BS 341 No. 8 W 0.860" x 14 TPI Carbon Dioxide Non Flammable BS 341 No. 10 G 1/2" Ammonia Toxic BS 341 No. 12 G 1/2" Sulphur Dioxide Toxic BS 341 No. 13 W 11/16" - 20 TPI Nitrous Oxide Oxidizer BS 341 No. 14 G 3/8" Hydrogen Cyanide, Nitric Oxide Toxic BS 341 No. 15 G 3/8" LH Carbonyl Sulphide, Hydrogen Sulphide Toxic G5/8 left gas bottle thread, BS341 No.2 (UK), male on bottle; flammable - acetylene G5/8 gas bottle thread, BS341 No.3 (UK), female on bottle; inerts - air, Ar, Ne, N2 G5/8 gas bottle thread, BS341 No.3 (UK), female on bottle; oxidizer - oxygen G5/8 left gas bottle thread, BS341 No.4 (UK), female on bottle; flammable - acetylene, H2 G5/8 left gas bottle thread, BS341 No.4 (UK), female on bottle; flammable - CO, methane, natural gas G5/8 gas bottle thread, BS341 No.6 (UK), male on bottle; toxic - Cl2, HCl G5/8 left gas bottle thread, BS341 No.7 (UK), male on bottle; flammable refrigerants W0.860-14 gas bottle thread, BS341 No.8 (UK), male on bottle; nonflammable - CO2 G1/2 gas bottle thread, BS341 No.10 (UK), male on bottle; toxic - NH3 G1/2 gas bottle thread, BS341 No.12 (UK), male on bottle; toxic - SO2 W11/16-20 gas bottle thread, BS341 No.13 (UK), male on bottle; oxidizer - N2O G3/8 gas bottle thread, BS341 No.14 (UK), male on bottle; toxic - HCN, NO G3/8 left gas bottle thread, BS341 No.15 (UK), male on bottle; toxic - carbonyl sulfide, H2S
Computer case screws !!6-32 UNC - common on hard drives, chassis backs, expansion cards, power supplies; 1/32 inch pitch, 3.51mm outer dia 4-40 UNC - common on D-sub ("Canon") ports M3
!4-40 UNC - thread on Canon trapezoid connector screws 10-32 UNF - SMC connectors !1/4-36 - SMA connectors !!3/8-32 UNEF - F connectors, BNC/TNC bulkhead connector threads 7/16-28 - TNC connectors 5/8-24 - N connectors, UHF connectors (PL-259/SO-239) 3/4-20 - HN connectors
http://brass-electronic-hardware.brass-inserts.com/brass-panel-nuts.html 1/4-40 1/4-32 9/32-28 5/16-24 3/8-32 3/8-27 3/8-24 UNF 3/8-18 NPS 7/16-28 UNEF 7/16-20 15/32-32 1/2-32 1/2-24 1/2-20 UNF 9/16-18 UNF 5/8-32 common 5/8-24 UNEF 5/8-18 UNF 11/16-28 11/16-27 11/16-24 UNEF 11/16-20 3/4-32 3/4-28 3/4-27 common? 3/4-25 3/4-24 3/4-20 UNEF 3/4-14 NPSM 3/4-16 UNF, common 13/16-28 13/16-27 7/8-24 7/8-20 UNEF 7/8-16 7/8-14 UNF 1-27 1-20 UNEF 1-16 1-14 1-12 UNF 1.1/4-18 1.1/4-16 1.3/8-12 UNF 1.3/8-6 UNC
http://kortick.com/wp-content/uploads/2016/10/KORTICK-CATALOG-216-10-03-16.pdf ...possibly mixed up diameter of drill-through hole and tpi tap?
33/64-13 M13.1x1.95 1/2" 41/64-11 M16.28x2.31 5/8" 49/64-10 M19.45x2.54 3/4" 1.1/64-8 M25.8x3.175 1"
1/4-32 UNEF - cinch connector 1/4-32 UNEF - 1/8" 3.12mm jack, metal M9x0.75 - 1/4" 6.35mm jack, metal M9x1.0 - 1/4" 6.35mm jack 3/8-32 UNEF - 1/4" 6.35mm jack, metal 4BA - 4mm banana jack female panel all-outside 5/16-24 UNF - 5.5mm power barrel jack 5/16-32 NEF - 5.5mm power barrel jack, metal 5/16-32 UNEF - 2mm banana jack M8x0.5 - 4mm banana jack M8x0.75 - 5.5mm power barrel jack, metal M8x1.0 - 5.5mm power barrel jack, plastic M12x0.75 - 4mm banana jack with safety sleeve
M8x1 - common thread on "aviation connectors" with sleeve nuts, eg. GX8, small ones M12x1 - common thread on "aviation connectors" with sleeve nuts, eg. GX12, mid ones M16x1 - common thread on "aviation connectors" with sleeve nuts, eg. GX16, large ones M19x1 - common thread on "aviation connectors" with sleeve nuts, eg. GX19/GX20, large ones M25x1.25 - common thread on "aviation connectors" with sleeve nuts, eg. GX25, large ones M29x1 - common thread on "aviation connectors" with sleeve nuts, eg. GX30, large ones
https://www.components-mart.my/datasheets/82/RM15WTLP-12P.pdf M13x0.75 - cable clamp nut on RM12 connector, cord clamps sleeve nuts M14x0.75 - panel nut on RM12 panel connector M16x0.75 - cable clamp nut on RM15 connector, cord clamps sleeve nuts M17x0.75 - panel nut on RM15 panel connector M20x0.75 - cable clamp nut on RM21 connector, cord clamps sleeve nuts M22x0.75 - panel nut on RM21 panel connector M24x0.75 - cable clamp nut on RM24 connector, cord clamps sleeve nuts M26x0.75 - panel nut on RM24 panel connector M28x0.75 - cable clamp nut on RM31 connector, cord clamps sleeve nuts M32x0.75 - panel nut on RM31 panel connector M19x1 - RM15 connector, "business end" sleeve nut M25x2 - RM21 connector, "business end" sleeve nut M29x2 - RM24 connector, "business end" sleeve nut M35x2 - RM31 connector, "business end" sleeve nut
1/4-32 NEF - potentiometer, dia 19mm back, dia 3.175mm shaft (3/4", 1/8"), MIL style RV5 M7x0.75 - potentiometer, dia 17mm back, dia 6.0mm shaft, option. with 18/22/24 teeth (also 13mm back) M8x0.75 - potentiometer, dia 24mm back, dia 6.0mm shaft, option. with 18/22/24 teeth M9x0.75 - potentiometer, dia 25mm back, dia 6.35mm shaft 3/8-32 NEF - potentiometer, dia 23mm back, dia 6.32mm shaft (0.91", 0.249"), also dia 6.0mm shaft opt. with 24 teeth M10x0.75 - potentiometer, dia 21mm back, dia 6.0mm shaft (also 17mm back)
1/8-27 NPT 1/4-40 NS 1/4-32 NEF 5/16-32 NEF 3/8-32 NEF 7/16-28 UNEF 15/32-32 NEF 1/2-28 NEF 5/8-27 NS 1 11/16-18 UNEF 2B 1 1/2-18 UNEF 2B switches: 10-48 M4x0.7 1/4-40 M6x0.75 M10x0.75 15/32-32 NS M12x0.75 11/16-27 NS M6x0.5 M8x0.75 M10x0.75 M12x0.75 M14x1 M16x1 M19x1 M22x1 M22x1.5 M24x1
common diameters: 8,8.3,12,16,18,30,31mm M5x0.5 - inductive proximity M8x1 M12x1 M12x - common M18x1 - common M18 M30x1.5 - common M36x1.5
M6x0.5 stoves M6x0.75 M8x1 (M8x1.25) M9x1 M10x1 M12x1.5 1/4-20 BSW 1/8-? 7/16-? 11/32-? 1/2-14 NPT thermowell 3/4-14 NPT thermowell speedometers: 5/8-18 7/8-18 temperature gauge 1/2-14 NPT car oil temp sensors
http://www.usignition.com/igniter-index.html 1/2-14 NPT M10x1 M14x1.25
M16x1.5 M20x1.5 M10x1 nozzles
http://www.ferroperm.com/?id=325&c=Sealed-bushing-filters.-Metric-size ; http://www.ferroperm.com/?id=324&c=Sealed-bushing-filters.-Inch-size ; M2.5(x0.45) M3(x0.5) M3.5(x0.6) M4(x0.7) M5x0.5 M6x0.75 M8x0.75 M8(x1.25) 4-40 UNC 6-32 UNC 8-32 UNC 12-32 UNEF 12-28 UNF 1/4-28 UNF 5/16-32 UNEF 5/16-24 UNF
M3.5 M3.5x0.75 M4(x0.7) M4.5x0.75 M5 M4x0.5 - Montesa 4Rt race replicas
kill-flash, sunshades: M31.8x0.75 riflescope objective lens thread, mostly 1-4x24 first focal plane scopes M45x0.75 riflescope objective lens thread, most threaded 40mm objective lenses, Meopta 42mm M46x0.75 riflescope eyepiece filter thread, some 50mm scopes, Meopta 40mm,42mm scopes M49x0.75 riflescope objective lens thread, Marcool 44mm scopes M50x0.75 riflescope objective lens thread M55x0.75 riflescope objective lens thread, most threaded 50mm objective lenses, Marcool 50mm scopes, Meopta Optika6 50mm M56x0.6 riflescope objective lens thread, some 4-16x50FFP scopes M58.2x0.75 riflescope objective lens thread, can fit Schmidt and Bender 5-25x56 etc M60.75x0.75 riflescope objective lens thread, Marcool 56mm scopes M61x0.75 riflescope objective lens thread, some 6-25x56FFP and 10-40x56FFP scopes, Meopta Optika6 56mm M26.5x0.75 riflescope objective lens thread, 22mm,24mm Meopta scope M42x0.75 riflescope objective lens thread, 40mm Meopta scope M47x0.75 riflescope objective lens thread, 44mm Meopta scope M48.5x0.75 riflescope objective lens thread, 44mm Meopta Optika6 scope M52x0.75 riflescope objective lens thread, 44mm,50mm Meopta scope M53x0.75 riflescope objective lens thread, 50mm Meopta scope M54x0.75 riflescope objective lens thread, 50mm Meopta MeoTac scope M57x0.75 riflescope objective lens thread, 50mm Meopta scope M59x0.75 riflescope objective lens thread, 56mm Meopta scope diameters: 32,42,44,48,50mm 42,47,57mm
https://www.cloudynights.com/topic/491256-what-is-the-thread-size-used-for-125-inch-filters/ 1.1/8-42 M28.575x0.605, optical filters, industry standard for 1.25" filters (except Questar/Brandon) M48x0.75 optical filters, industry standard for 48mm filters, threads into 2" eyepieces XXx0.75 usual for XXmm filters http://www.rudolf-reiser.de/astro_atm_gewinde_en.html M28.5x0.5 on astronomy 1.1/4(31.8mm) eyepieces M28.5x0.6 on astronomy 1.1/4(31.8mm) eyepieces 1.1/8-40 on astronomy 1.1/4(31.8mm) eyepieces M29.5x0.5 on astronomy 31.0mm eyepieces (Lichtenknecker) M43x0.75 on astronomy eyepieces, Pentax XW - Frontside Camera Adaptor M48x0.6 on astronomy 2" eyepieces (less common?) M48x0.75 on astronomy 2" eyepieces M59x0.75 on astronomy Lichtenknecker (System 64) eyepieces 2"-24 on astronomy telescopes, adaptor at focuser; Celestron/Meade 8 Inch SCs, Intes Micro 715 3.3"-16 on astronomy telescopes, adaptor at focuser; Celestron C11/C14 4"-16 on astronomy telescopes, adaptor at focuser; Meade LX200 16 Inch SC M35x1 on astronomy telescopes, adaptor at focuser; Meade ETX 90/105/125 M36.4x1 on astronomy telescopes, adaptor at focuser; Vixen/Lichtenknecker M42x1 on astronomy telescopes, adaptor at focuser; Russian Telephoto Lens MTO 11-CA M43x1 on astronomy telescopes, adaptor at focuser; Vixen M44x1 on astronomy telescopes, adaptor at focuser; Zeiss M56x1 on astronomy telescopes, adaptor at focuser; Synta Refractors (Bresser, Skywatcher, Konus et. al.) M60x0.75 on astronomy telescopes, adaptor at focuser; Vixen / GSO 2"- Focuser M68x1 on astronomy telescopes, adaptor at focuser; Zeiss M109.35-24 on astronomy telescopes, Astrophysics Traveler 2.7" focuser, telescope side M69.5-24 on astronomy telescopes, Astrophysics Traveler 2.7" focuser, adapter side M123.75-24 on astronomy telescopes, Starlight Instruments 3,5" Feathertouch Focuser, telescope side M104.1-24 on astronomy telescopes, Starlight Instruments 3,5" Feathertouch Focuser, telescope side M42x1 photo adapter, Praktica, MTO 11-CA M42x0.75 photo adapter, T2-Mount, T-mount (T = Tamron) 1"-32 C-mount, CS-mount W39-26 photo adapter, Lenses for Enlargers, Leica-Thread M54x0.75 photo adapter, Series 7 (e.g. Fisheye-Converter)
M32x0.5 optical filter; on Watershot Underwater Housing for Samsung Galaxy S3, many of the older Kern Switar lenses M32x0.75 optical filter; on Watershot Underwater Housing for Apple iPhone M39x?? M49x?? ? M52x?? most common on compact housings M67x?? most common on DSLR/mirrorless housings
M5.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M6.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M7.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M8.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M9.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M10.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M11.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M12.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M13.5x0.5 for 13mm-dia lens mounts, eg. Thorlab M14.5x0.5 for 14mm-dia lens mounts, eg. Thorlab M15.5x0.5 for 15mm-dia lens mounts, eg. Thorlab M16.5x0.5 for 16mm-dia lens mounts, eg. Thorlab M17.5x0.5 for 17mm-dia lens mounts, eg. Thorlab M19.5x0.5 for 18mm-dia lens mounts, eg. Thorlab M20.5x0.5 for 20mm-dia lens mounts, eg. Thorlab 3/4-40 for 18mm-dia lens mounts, eg. Thorlab 1-32 for C-mount and CS-mount lens mounts, eg. Thorlab M31.5x0.5 M32.5x0.5 M33.5x0.5 M34.5x0.5 M35.5x0.5 M36.5x0.5 M37.5x0.5 M38x0.5 M39.5x0.5 M40.5x0.5 M41.5x0.5 M42.5x0.5 M43.5x0.5 M44.5x0.5 M45.5x0.5 M46.5x0.5 M47.5x0.5 M48.5x0.5 M75.5x0.5 M100.75x0.5 M5.5x0.5 lens mounting ring, for 5mm-dia lens mounts, eg. Thorlabs M6.5x0.5 lens mounting ring, for 6mm-dia lens mounts, eg. Thorlabs M7.5x0.5 lens mounting ring, for 7mm-dia lens mounts, eg. Thorlabs M8.5x0.5 lens mounting ring, for 8mm-dia lens mounts, eg. Thorlabs M9.5x0.5 lens mounting ring, for 9mm-dia lens mounts, eg. Thorlabs M10.5x0.5 lens mounting ring, for 10mm-dia lens mounts, eg. Thorlabs M11.5x0.5 lens mounting ring, for 11mm-dia lens mounts, eg. Thorlabs M12.5x0.5 lens mounting ring, for 12mm-dia lens mounts, eg. Thorlabs M13.5x0.5 lens mounting ring, for 13mm-dia lens mounts, eg. Thorlabs M14.5x0.5 lens mounting ring, for 14mm-dia lens mounts, eg. Thorlabs M15.5x0.5 lens mounting ring, for 15mm-dia lens mounts, eg. Thorlabs M16.5x0.5 lens mounting ring, for 16mm-dia lens mounts, eg. Thorlabs M17.5x0.5 lens mounting ring, for 17mm-dia lens mounts, eg. Thorlabs M19.5x0.5 lens mounting ring, for 18mm-dia lens mounts, eg. Thorlabs M20.5x0.5 lens mounting ring, for 20mm-dia lens mounts, eg. Thorlabs 3/4-40 some lens mounting rings, for 18mm-dia lens mounts, eg. Thorlabs 1-32 some lens mounting rings, for C-mount and CS-mount lens mounts, eg. Thorlabs M31.5x0.5 some lens mounting rings, eg. Thorlabs M32.5x0.5 some lens mounting rings, eg. Thorlabs M33.5x0.5 some lens mounting rings, eg. Thorlabs M34.5x0.5 some lens mounting rings, eg. Thorlabs M35.5x0.5 some lens mounting rings, eg. Thorlabs M36.5x0.5 some lens mounting rings, eg. Thorlabs M37.5x0.5 some lens mounting rings, eg. Thorlabs M38x0.5 some lens mounting rings, eg. Thorlabs M39.5x0.5 some lens mounting rings, eg. Thorlabs M40.5x0.5 some lens mounting rings, eg. Thorlabs M41.5x0.5 some lens mounting rings, eg. Thorlabs M42.5x0.5 some lens mounting rings, eg. Thorlabs M43.5x0.5 some lens mounting rings, eg. Thorlabs M44.5x0.5 some lens mounting rings, eg. Thorlabs M45.5x0.5 some lens mounting rings, eg. Thorlabs M46.5x0.5 some lens mounting rings, eg. Thorlabs M47.5x0.5 some lens mounting rings, eg. Thorlabs M48.5x0.5 some lens mounting rings, eg. Thorlabs M75.5x0.5 some lens mounting rings, eg. Thorlabs M100.75x0.5 some lens mounting rings, eg. Thorlabs
@ 1/8-40 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 3/16-32 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 3/16-24 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 7/32-28 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1/4-26 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1/4-20 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 9/32-26 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 5/16-22 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 5/16-18 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 3/8-20 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 3/8-16 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 7/16-18 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 7/16-14 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1/2-16 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1/2-12 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 9/16-16 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 9/16-12 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 5/8-14 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 5/8-11 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 11/16-14 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 11/16-11 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 3/4-12 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 3/4-10 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 7/8-11 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 7/8-9 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1-10 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1-8 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1.1/8-9 Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1.1/8-7 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1.1/4-9 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1.1/4-7 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1.3/8-8 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1.1/2-8 TWF Truncated Whitworth Fine; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSF; H28 1944 @ 1.1/2-6 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1.3/4-5 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 2-4.1/2 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 2.1/4-4 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 2.1/2-4 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 2.3/4-3.5 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 3-3.5 TWC Truncated Whitworth Coarse; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSW; H28 1944 @ 1/8-28 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 1/4-19 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 3/8-19 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 1/2-14 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 5/8-14 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 3/4-14 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 7/8-14 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 1-11 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 1.1/4-11 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944 @ 1.1/2-11 TWPP Truncated Whitworth Parallel Pipe; US WW2 wartime standard; flat root/crest, 55deg, compatible with BSPP/G; H28 1944
taper 3/16 in/ft 4.3916-10 British water well casing, nominal bore 4", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 6.5165-10 British water well casing, nominal bore 6", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 8.5003-8 British water well casing, nominal bore 8", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 10.6251-8 British water well casing, nominal bore 10", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 12.6251-8 British water well casing, nominal bore 12", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 13.8749-8 British water well casing, nominal bore 13", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 15.8749-8 British water well casing, nominal bore 15", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 18.8749-8 British water well casing, nominal bore 18", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 21.8437-8 British water well casing, nominal bore 21", taper 3/16 in/ft, thread diameter at gauge length 1.3/8" 24.8437-8 British water well casing, nominal bore 24", taper 3/16 in/ft, thread diameter at gauge length 1.3/8"
Whitworth bore tpi 0.50..0.70 60 0.75..0.95 60 48 1.00..1.20 60 48 36 1.25..1.50 60 48 36 30 1.55..1.75 48 36 30 1.80..2.50 36 30 2.60..3.00 36 18 and 30 tpi where listed not practical nominal major dia of screw = bore+factor (0.025/60tpi, 0.030/48tpi, 0.040/36tpi, 0.050/30tpi) where diameter x tpi > about 72, thread tends to jam when screwed home on to square shoulders
https://www.wixfilters.com/Lookup/FilterBySize.aspx?catid=3&styleid=7 ; 7/16-20 lube; rare 13/16-16 lube, hydraulic, transmission, turbocharger, power steering; common-ish 3/4-16 lube, hydraulic; very common 3/4-20 lube, transmission; rare 5/8-18 lube; common-ish 7/8-14 lube, hydraulic; rare-ish 7/8-16 lube; rare 31/32-20 hydraulic; rare 0.974-20 hydraulic; rare 1-12 lube, hydraulic, transmission; very common 1-14 hydraulic/transmission; rare 1-16 lube; unusual 1.1/8-12 lube, hydraulic; rare 1.1/8-16 lube, hydraulic, transmission; common 1.1/4-12 lube, hydraulic, transmission; unusual 1.5/16-12 hydraulic/transmission; unusual 1.3/4-12 lube, hydraulic, transmission; common-ish 1.3/4-16 hydraulic; unusual 1.3/8-12 hydraulic/transmission; common-ish 1.3/8-16 lube; unusual 1.1/2 UN 2A hydraulic 1.1/2-12 lube; common-ish 1.1/2-16 lube, hydraulic; pretty common 1.5/8-12 lube; unusual 2-12 hydraulic, transmission; unusual 2-16 hydraulic; uncommon 2.1/4-12 lube; unusual 2.1/2-6 hydraulic; rare 3-8 hydraulic; rare 3/4-14 BSP hydraulic; very common 1.1/4-11 BSP lube, hydraulic; common 1.1/2-11 BSP hydraulic; unusual M14x1.5 lube; rare M16x1.5 lube; rare-ish M18x1.5 lube, some hydraulic; unusual M20x1 lube; rare M20x1.5 lube, hydraulic, transmission; common M22x1.5 lube; common M23x1.5 hydraulic/transmission; rare M24x1.5 lube, hydraulic, transmission; unusual M24x2 lube, hydraulic; rare-ish M26x1.5 lube; unusual M27x1.5 lube; rare M27x2 lube, hydraulic; rare M30x1.5 lube; rare M30x2 lube; unusual M32x1.5 lube; rare M32x2 hydraulic; rare M36x1.5 lube; rare-ish M39x1.5 lube; rare M39x1.75 lube; rare M40x2 hydraulic; rare M42x2 hydraulic, lube; common-ish M45x1.5 lube, hydraulic; rare M45x2 hydraulic; rare M48x2 hydraulic; rare M52x1.5 lube; rare M55x1.5 hydraulic; rare M60x2 hydraulic; rare M68x2 hydraulic; rare M72x2 hydraulic; rare M87x2.5 hydraulic; rare M90x2 hydraulic, lube; rare-ish M92x2 lube; rare M92x2.5 lube; rare M95x2 lube; rare M95x2.5 lube; rare-ish M108x2.5 hydraulic; rare M120x2 hydraulic; rare M126x4 lube; rare
https://www.aboveboardelectronics.com/documents/Essentra-Thread-Inserts-Tools-and-Kits.pdf 10-32 EZ-Lok steel, 4-40 1/4-20 EZ-Lok steel, 6-32 5/16-18 keylocking and EZ-Lok steel thinwall, 10-32, 10-24; keylocking heavy duty and EZ-Lok steel, 8-32; extra heavy duty, 6-32 3/8-16 keylocking and EZ-Lok steel thinwall, 1/4-28, 1/4-20; keylocking heavy duty and EZ-Lok steel, 10-32, 10-24; EZ-Lok steel, M6x1 7/16-14 keylocking and EZ-Lok steel thinwall, 5/16-24, 5/16-18; keylocking heavy duty and EZ-Lok steel, 1/4-28, 1/4-20 1/2-13 keylocking and EZ-Lok steel thinwall, 3/8-24, 3/8-16; keylocking heavy duty and EZ-Lok steel, 5/16-24, 5/16-18; EZ-Lok steel, M8x1.25; keylocking extra heavy duty and EZ-Lok steel extra heavy, 1/4-20 9/16-12 keylocking and EZ-Lok steel thinwall, 7/16-20, 7/16-14; keylocking heavy duty and EZ-Lok steel, 3/8-24, 3/8-16; EZ-Lok steel, M10x1.25, M10x1.5; keylocking extra heavy duty and EZ-Lok steel extra heavy, 5/16-18 5/8-11 keylocking and EZ-Lok steel thinwall, 1/2-20, 1/2-13; keylocking heavy duty and EZ-Lok steel, 7/16-20, 7/16-14; keylocking extra heavy duty, 3/8-24, 3/8-16; EZ-Lok steel extra heavy, 3/8-16 3/4-16 keylocking heavy duty, 1/2-20, 1/2-13, 9/16-12 3/4-10 EZ-Lok steel, 1/2-20, 1/2-13, 9/16-18, 9/16-12, M12x1.75 7/8-14 keylocking heavy duty, 5/8-18, 5/8-11; extra heavy duty, 1/2-13 7/8-9 EZ-Lok steel, 5/8-18, 5/8-11, M14x2; EZ-Lok steel extra heavy, 1/2-13 1-12 keylocking extra heavy duty, 5/8-18, 5/8-11 1-8 EZ-Lok steel, 3/4-16, 3/4-10, M16x2; EZ-Lok steel extra heavy, 5/8-11 1.1/8-12 keylocking heavy duty, 3/4-16, 3/4-10 1.1/4-12 keylocking heavy duty, 7/8-14, 7/8-9; extra heavy duty, 3/4-16, 3/4-10 1.1/4-7 EZ-Lok steel, 7/8-9 1.3/8-12 keylocking heavy duty and EZ-Lok steel, 1-14, 1-8 1.1/2-12 keylocking heavy duty, 1.1/8-7 1.5/8-12 keylocking heavy duty, 1.1/4-12, 1.1/4-7 1.7/8-12 keylocking heavy duty, 1.1/2-12, 1.1/2-6 M6x1 EZ-Lok steel, 6-32, M3x0.5 M8x1.25 keylocking thinwall, M5x0.8; EZ-Lok steel, 8-32, M4x0.7, M5x0.8; keylocking heavy duty, M4x0.7 M10x1.25 keylocking thinwall, M6x1; keylocking heavy duty, M5x0.8 M10x1.5 EZ-Lok steel, 10-32, 10-24, M6x1 M12x1.25 keylocking thinwall, M8x1.25; keylocking heavy duty, M6x1 M12x1.75 EZ-Lok steel, 1/4-20, 5/16-18, M8x1.25 M14x1.5 keylocking thinwall, M10x1.25, M10x1.5; keylocking heavy duty, M8x1, M8x1.25 M16x1.5 keylocking thinwall, M12x1.75; keylocking heavy duty, M10x1.25, M10x1.5 M16x2 EZ-Lok steel, 3/8-16, 1/2-13, M10x1.5, M12x1.75 M18x1.5 keylocking heavy duty, M12x1.25, M12x1.75 M20x1.5 keylocking heavy duty, M14x1.5, M14x2 M22x1.5 keylocking heavy duty, M16x1.5, M16x2 M24x1.5 keylocking heavy duty, M18x1.5 M24x3 EZ-Lok steel, M16x2 M30x2 keylocking heavy duty, M20x1.5, M20x2.5 M32x2 keylocking heavy duty, M22x1.5 M33x2 keylocking heavy duty, M24x3 M36x4 EZ-Lok steel, M20x2.5 common uncommon sizes: https://images-na.ssl-images-amazon.com/images/I/A1mpY8GZsSL.pdf 4-36 11/16-16 11/16-11 1-14
https://gasmaskandrespirator.fandom.com/wiki/Thread:11144 DIN 40mm gas mask filter thread "DIN", round/knuckle thread 3.5mm pitch; masks also take GOST and STANAG filters; common in WW2 by Axis Rd40x1/7" gas mask filter thread "STANAG", also "RD40", round/knuckle thread, NATO standard gas masks, STANAG 4155, Rd40x1/7", 3.63mm pitch Kr40h4 gas mask filter thread "GOST", round/knuckle thread, Soviet standard, GOST 8762-75, Kr40h4; GOST filter fits STANAG mask but not vice versa 3M 6000 series 60x4 gas mask filter thread "60mm", round/knuckle thread 4mm pitch; Finnish M51 series, Canadian C3, (Including Dutch export models), American M9 (Including Yugoslavian and Iraqi clones), and also British WW2 D-Day 'Lightweight' respirators and 1950's models bayonet assembly on some industrial masks 60mm thread from here: https://www.thingiverse.com/thing:2533057
3/4-14 NPT common on steel drums/barrels, smaller one (larger is 2" NPT), for 19mm openings (DN20) 3/4 BSPP 1.1/2 2"(-11.5) NPS common on steel drums/barrels, larger one (smaller is 3/4 NPT), for 57mm (51mm) openings (DN50) 2" BSPP 2" buttress on some steel drums/barrels, for 63mm openings, "US drum thread", "coarse thread" M64 metric G3/4 G2" some 2" caps have 3/4" thread for a center tap metric: BCS 38x6 BCS 56x4, metric buttress, european plastic drums CCS 60x6 jerrican? BCS 64x5, metric buttress, less common BCS 70x5 BCS 70x6 ("BCS 70mm"), metric buttress, most commonly found in Europe and Asia BCS 71x4 https://www.usplastic.com/catalog/files/charts/77853.pdf CCS 32x4 CCS 36x3 CCS 38x3 CCS 39x3 CCS 45x4 CCS 50x4 CCS 25x3 CCS 52x4 CCS 54x4 CCS 61x3 CCS 63x4 CCS 65x6 CCS 80x6 CCS 90x6 CCS 160x7 CCS 240x12 CCS 60x6 An opening with some very heavy coarse, weird thread in it known as the dreaded "buttress" thread: Doesn't fit any standard faucets or pumps. Buttress threads are a holdover from the early days of plastic drums. Back then, it was difficult to precisely mold pipe threads directly into the drum. NPS plugs would leak, cross thread, or strip out when you tightened them. The heavy, strong buttress thread solved the problem. Today, plastic drum technology is vastly improved, and NPS plugs now perform just as well as buttress plugs.
https://www.kstools.com/cz/produkty/specialni-naradi-na-nakladni-vozidla/motor-system-chlazeni-motoru/soupravy-nastroju-pro-servisni-diagnostiku-chladiciho-systemu/1863/souprava-nastroju-pro-servisni-diagnostiku-chladiciho-systemu-master-25dilna M34x3 M42x2.5 M42x3 M45x3 M46x3 M48x2.5 M48x4 M50x2.5 M50x3 M52x3 M58x3 M60x4 M62x3
M4.5x0.5 rare M6x0.5 rare M6x0.75 common M6x1 rare M7x0.75 rare M7x1 M8x0.75 M8x1 M8 M9x1 M10x0.75 rare M10x1 common M10x1.5 M11x1 M12x1 M12x1.5 M13x1 M14x1 rare M15x1 rare M15x1.25 rare M16x1.5 rare 12 UNF rare 12-28 UNF rare 1/8 1/8 NPT rare 1/4 1/4 IT internal 1/4 NPT rare 3/8 3/8 UNF rare 5/16 UNEF rare 7/16 1/2 UNEF 9/16 UNF
http://content.penturners.org/library/general_reference/taps_dies_kitless.pdf M6.4x0.6 Bock size 5 nibs M6.5x0.5 Jowo size 5 nibs, Heritance size 5 nibs (discontinued), Schmidt roller writer rollerball M7.9x0.6 Bock size 6 nibs M7.5x0.5 Jowo size 6 nibs M8.4x0.75 Heritance size 6 nibs (discontinued) M8.4x1 common nose cone/front section, front ends for Baron/Sedona/Navigator/etc (M8.5x1 also works) M9x0.75 common nose cone/front section M10x0.75 common nose cone/front section, common cap thread M10x0.75x3 triple-lead, common cap thread M10x1 common nose cone/front section, El Grande kit front ends M12x0.75 common cap thread M12x0.75x3 triple-lead, common cap thread M13x1 common cap thread M14x0.8x3 triple-lead, common cap thread M14x1 common cap thread https://www.practicalmachinist.com/vb/general/anyone-know-where-find-m6-4x0-6-tap-274662/index2.html Pelican fountain pens threads: 9/32-36 11/32-36 3/8-36 https://www.penturners.org/threads/kitless-pen-threading.116938/ Thread sizes for pens M6.4x0.5 Schmidt roller/small FP feeds M6.4x0.75 Jr Gent feed holder M7x0.75 Richard Greenwald click transmission M7.4x0.5 Meisternib M8x0.5 Cigar transmission M8x0.75 Cigar nib and final M8.4x0.75 Large FP feeds M8.4x1 Baron/Navigator front end M8.5x1 Sierra/wall street transmission M9x0.75 finals and sections M10x1 El Grande/ Churchill section M12x0.8x3 El Grande/ Churchill cap threads Also, M12x0.75 and M12x0.8x3 are used for a lot of cap threads and M9x0.75 for finials and sections. Really it's about what fits for the design you want https://www.fpnibs.com/accessories/taps.html M6.5x0.5 size 5 Jowo nibs, Bock 076/180/060 nibs M7.5x0.5 size 6 Jowo nibs, Bock 250 nibs M8.5x0.5 size 6 Ebonite nibs M9.5x0.5 size 8 Jowo nibs, Bock 380 nibs https://www.beaufortink.co.uk/bushes-drills-bits-thread-taps-dies M6.4x0.6 Bock size 5 M6.5x0.5 Refillable Rollerball nibs, also compatible with Jowo, Schmidt and Heritance size 5 fountain pen nibs M7.9x0.6 Bock size 6 M8.5x1 Bock intermediate section for size 5,6,8 M10x0.8x3 triple-lead, pen cap M11x0.8x3 triple-lead, pen cap M12x0.8x3 triple-lead, pen cap M13x0.8x3 triple-lead, pen cap M14x0.8x3 triple-lead, pen cap http://www.silverpenparts.com/page7.html M6.5x0.5 nib M7.4x0.5 #6 nib and feed holder assembly, for the Jowo M9.4x0.5 front of the piston filler M8.5x1 for the Baron/Sedona Navigator style pens and the Sierra style transmission threads M8.5x0.75 Parker Duo fold and Heritance #6 feeds 9/32-36 Pelikan 200/400/600 Nibs and feeds as well as Esterbrook and Reform 11/32-36 (M10x0.75) nose cone threads M8.5x0.5 nose cone threads M8.5x0.75 nose cone threads M10x0.75x3 triple-lead, pen cap Parker pens: 36 and 48 tpi
M3x0.5 M3.5x0.5 common M4x0.5 common M6x0.5 common M10x1 threads http://www.magnet-tech.com/core/NiZn/th.htm OC3: thread 60deg, pitches 0.35,0.50,0.60,0.75,1.00 OC4: thread 90deg, pitches 0.50,0.60,0.80 threads http://www.buildweb.com.tw/ferrites/bead-toroidal-core/threaded-spec.htm 4.75x0.5 5.00x0.5 5.95x0.5 6.50x0.6 6.70x0.6 6.80x0.6 7.45x0.8 threads https://assets.noviams.com/novi-file-uploads/tta/pdfs-and-documents/Standard_Specification_for_Ferrite_Threaded_Cores.pdf pitch 28,32,40 1/4 .245-28,40 5/16 .300-28 https://neosid.de/en/products/ferrite-components-and-accessories/adjustment-elements/screw-cores/?p=2 3x0.5 3.5x0.75 4x0.5 5x0.75 6x0.75 6x1
euro-style clock movements: hour hand: 4.95mm round hole minute hand: M3.5x0.35 thread, cut faces from opposite faces to 2.8mm width seconds hand: 0.8mm round hole
https://scilab.co.jp/product/mems/download/piezo_catalog_120930_2.pdf M2, M3, M4, M5, M6, M8 M8x0.5 M12x0.5 M22x0.75 M32x0.75 external threads: M8x0.5 M10x0.75 M12x0.75 M14x1 M18x1 optic adaptors for ring actuators: M14x0.5 M12x0.5 M22x0.5 M28x0.75
BSP 1/4 G1/4 - most common G1/2 G3/8 G1/8 NPT 1/4 M12 7/16-20 UNF SAE
M10x0,75 M12x1 M15x1 M17x1 M20x1 M25x1,5 M30x1,5 M35x1,5 M40x1,5 M45x1,5 M50x1,5 M55x2 M60x2 M65x2 M70x2 M75x2 M80x2 M85x2 M90x2 M95x2 M100x2 M105x2 M110x2 M115x2 M120x2 M125x2 M130x2 M135x2 M140x2 M145x2 M150x2 M155x3 M160x3 M165x3 M170x3 M180x3 M190x3 M200x3
[ ref]
8-32 - TR post, imperial, top side
1/4-20 - TR post, imperial, bottom side
M4x0.7 - TR post, metric, top side
M6x1.0 - TR post, metric, bottom side
matrix 1"x1" of 1/4-20 holes: optical bench, imperial
matrix 25x25mm of M6 holes: optical bench, metric
double-density boards: mix 8-32 and 1/4-20 (or M4 and M6), larger holes in 1" (or 25mm) raster, smaller holes in the other positions of a matching 0.5" (or 12.5mm) raster
also boards with 4-40 and M3 holes
black anodized to reduce stray light reflections
unanodized for use in vacuum
M16x0.75 smaller CO2 lasers M22x0.75 most common M24x0.5 rare M29x1 uncommon, high power CO2 laser beam expanders M30x0.75 on some YAG laser lenses M30x1 Nd:YAG, 532nnm; on zoom beam expanders, alternative to C-mount M33x0.5 rare M44x1 rare M52x1.5 standard on CO2 lasers M56x1 on some YAG laser lenses
[ ref]
M2.5x0.2 - adjustment screws
M3x0.2 - adjustment screws
M3x0.25 - adjustment screws
M3 - standard M3, mounting holes, less common
M4x0.7 - standard M4, mounting holes smaller
M4.5x0.5 - adjuster nut
M6x0.25 - adjustment screws
M6x0.5 - aspheric lens housing
M6x1.0 - standard M4, mounting holes larger
M8x0.5 - aspheric lens housing, some diode laser lenses
M9x0.5 - aspheric lens housing, common diode laser lenses
M10x0.5 - aspheric lens housing
M11x0.5 - mounted-pair aspheric lens housing
M12x0.5 - aspheric lens housing, S-mount
M14x0.5 - similar to M12x0.5, uncommon
M25x0.75 - objective lenses, microscopes
1/4-80 - adjustment screws?
4-40
6-32
8-32 - mounting holes smaller
1/4-20 - mounting holes larger
M17x0.75 - NF mount; up to 40% smaller and 50% lighter lens than C/CS mount; larger sensors than S-mount
M35x0.75 - lens mount, TFL mount; 17.526mm flange distance equal to 1"-32 C-mount, "larger-diameter C-mount", proposed C-mount alternative to large sensors
M25x1.5 M32x1.5 M40x1.5 M50x1.5 M60x1.5 M63x1.5 M70x1.5 M75x1.5 M80x1.5 M85x1.5 M90x1.5 M100x1.5 M110x1.5
https://eshop.wavelength-oe.com/ M16x0.75 common, "miniBET" M22x0.75 common 1"-32 C-mount M28x0.75 M29x0.75 M30x1 common, "uniBET" M38x0.75 F-theta scan lenses M36x0.75 M39x1 second most common M55x1 uncommon M65x1.5 some lens assemblies, STU2 and STU3 M70x1 on some thread ring M85x1 laser galvo F-Theta scan lens, Nd:YAG engraver lasers, most common M92x1 M95x1 3.875-32 3.7/8-32, M98.425x0.794 M102x1 M110x1 M120x1 M132x1 M150x1 TK52 TK60 TK87 TK133 TK145 TK267 wavelengths: 1850nm 1550nm 1064nm most common; fused silica has low absorption 808nm 532nm 405nm 355nm 266nm
https://www.ttcnorthamerica.com/wp-content/uploads/2019/10/KGT_Cap-nut-for-collet-sleeves.pdf M28x1 Citizen M30x1.5 Strohm M31x1.5 STAR M32x1 Citizen M32x1.5 Feinler M33x1.5 STAR M35x1.5 Citizen M36x1.5 STAR M38x1.5 STAR M40x1.5 Citizen, Feinler, STAR, Tornos M43.5x2 Traub M44x1.5 STAR M45x1.5 STAR M46x1.5 Tsugami M50x1 STAR M50x1.5 Citizen, STAR M52x3 Traub M55x1.5 Citizen M56x1.5 STAR, Strohm M60x1 STAR M60x1 STAR M62x2.5 Traub M65x1.5 Citizen M66x3 SAIC M68x3 Spinner M70x1.5 Citizen M70x3 Traub M70x1.5 Citizen, Tsugami M75x1.5 Citizen M76x1.5 STAR M80x1.5 STAR M80x2 Spinner M80x3 Traub M85x1.5 STAR M98x3 Traub M32x1L Tornos M33x1.25L Tornos M40x1.5L Index ON12/OR12 M52x2L Index 12/24/DG12 M58x2L Index 18 M63x2L Index 25/C19 M74x2L Index 24/B30/C29 M85x2L Index B42/36/E42/ER42 M108x2L Index 52/B60
M39x1.5 MAN, RVI, Volvo M39x1.5 left(?) M41x1.5 DAF M22x1.5 most common air dryer ports M18x1.5 on air hoses M16x1.5 on air hoses
[ ref]
6-80
3/16-100
3/16-120
1/4-80
1/4-100
M2.5x0.20
M3x0.20
M3x0.25
M4x0.25
M6x0.25
6-80 adjustment screws
3/16-120 adjustment screws
3/16-100 adjustment screws
1/4-100 adjustment screws
1/4-80 adjustment screws
M2.5x0.2 adjustment screws
M3x0.2 adjustment screws
M3x0.25 adjustment screws
M4x0.25 adjustment screws
M6x0.25 adjustment screws
!M12x0.5 - lens mount, S-mount !M9x0.5 - laser diode module lenses M4.2x0.2 - lens mount (1/7" sensors) M4.6x0.25 - lens mount (1/5", 2.4mm, 3.8mm sensors, industrial endoscopes) M5x0.35 - lens mount (1/6", 1/5" sensors) M5.5x0.35 - lens mount (1.7", 1/5.8", 1/5", 1/4" sensors) M6x0.35 - lens mount (1/4", 5.2mm, 4.85mm sensors), believed to be in Raspbery Pi camera v1 M6.4x0.25 - lens mount (1/3" sensors) M7x0.35 - lens mount (1.8", 1.7", 1/6", 1/5", 1/4", 1/3.6", 1/3.2", 1/2.7", 4.85mm sensors) M8x0.35 - lens mount (1/4", 1/3" sensors) !M8x0.5 - lens mount (1/5", 1/4", 1/3" sensors; sometimes occurs in diode laser modules), second most common in small cams !!!M9x0.5 - lens mount (1/2.7", 1/3", 1/3.2" sensors; also commonly encountered in diode laser modules) M10x0.5 - lens mount (1/4", 1/3" sensors), third most common after M12x0.5 and M8x0.5 !!!M12x0.5 - lens mount (the S-mount, listed in the table) ? M14x0.5 5/8-32 - lens mount, D 0.8"-36 - microscope objective, RMS thread (older) M19x0.75 - microscope objective, apparently less common M24x0.75 - microscope objective, apparently less common, some thermal camera lenses M24x1 - lens mount, Narciss M25x0.75 - microscope objective, Leica/Nikon Biologicals 1"-32 - CCTV, C-mount/CS-mount M26x0.6 - lens mount, Arcturus binoviewer M26x0.706 - microscope objective, BD mount M26x0.75 - microscope objective, apparently less common M27x0.75 - microscope objective, Zeiss M28x0.75 - microscope objective, apparently less common M30x0.75 - microscope objective, apparently less common M32x0.75 - microscope objective M37x0.75 - lens mount, early T-thread, Tamron, microscopes M37x1 - lens mount, M37, LTM (Leica Thread Mount) M39-26 - lens mount, M39 Leica LSM, 26tpi, 35mm cameras M39x1 - lens mount, M39, LTM (Leica Thread Mount), 35mm cameras with rangefinders, common photo enlarger lenses M40x0.75 - microscope objective, apparently less common M40x1 - lens mount, M40, Practiflex M42x0.75 - lens mount, T-mount, T2, standard to attach cameras to microscopes M42x1 - lens mount, M42, 35mm SLR cameras, universal/common M47x0.75 - lens mount, T-thread, Tokina M48x0.75 - lens mount, "newly emerging de-facto standard", DSLR, replacement for M42 to better use 2" focusers/correctors M57x1 - lens mount, Bronica S2 medium-format M60x0.75 - lens mount, less common http://www.optics-online.com/Solutions/security.asp?sort=ImagerFormat M8x0.35 M10x0.35 M16x0.35 M20x0.35 for 1" 4k+ sensors http://www.macrolenses.de/objektive.php M18x0.5 lens mount, Leitz Wetzlar Ludar, Schneider-Kreuznach D-Claron, uncommon M19x1 lens mount, Schneider-Kreuznach D-Claron, uncommon M20x0.75 lens mount, Carl-Zeiss Mikrotar, uncommon M22x0.5 lens mount, Carl-Zeiss S-Planar, uncommon M23x0.5 lens mount, Carl-Zeiss Tessar, uncommon M25x0.5 lens mount, Carl-Zeiss Tessar, Schneider-Kreuznach Repro-Claron, uncommon M26.5x0.5 lens mount, Carl-Zeiss Mikrotar, Rodenstock Apo-Ronar, uncommon 1.325"-8 lens mount, 33.66x3.175, Bausch and Lomb Micro Tessar, uncommon M28x0.5 lens mount, Carl-Zeiss Tessar, uncommon M29.5x0.5 lens mount, Schneider-Kreuznach M-Componon, uncommon M30x0.5 lens mount, Schneider-Kreuznach Spezial-Anastigmat, Cassar, uncommon M32x0.5 lens mount, Carl-Zeiss S-Planar, uncommon M32x1 lens mount, Cooke copying lens, Rank-Taylor-Hobson Butar, Vickers Macro Lens, uncommon M33x0.5 lens mount, Carl-Zeiss Apo-Tessar, Apo-Germinar, Tessar uncommon M34x0.75 lens mount, Reichert Neu-Polar, Polar, uncommon M35x0.75 lens mount, Carl-Zeiss Luminar, uncommon M36x0.5 lens mount, Carl-Zeiss S-Planar, uncommon M36x0.75 lens mount, Leitz Wetzlar Summar, Photar, uncommon 1.55"-40 lens mount, 39.37x0.635, Kodak Ektar, uncommon M40x0.5 lens mount, Carl-Zeiss S-Planar, uncommon M44.5x0.5 lens mount, uncommon M45x0.5 lens mount, Carl-Zeiss Tessar, uncommon M55x0.5 lens mount, Carl-Zeiss S-Planar, uncommon M70x1 lens mount, 105mm Printing Nikkor older model 0.535"-40 - SM05, ThorLabs, optics and microscope objectives, optics dia 0.5" 1.035"-40 - SM1, ThorLabs, optics and microscope objectives, optics dia 1" M26x0.706 (36tpi) - microscope objective, BD mount, Mitutoyo M27x1.0 - microscope objective M30.5x0.5 - SM30, ThorLabs, optics and microscope objectives, optics dia 30mm M34x1.0 - microscope objective, Zeiss and Nicon M40x0.706 - microscope objective 2.035"-40 - SM2, ThorLabs, optics and microscope objectives, optics dia 2" 3.035"-40 - SM3, ThorLabs, optics and microscope objectives, optics dia 3" https://www.optikos.com/products/lens-mount-adapters/ 5/8-32 - 15.875x0.794, D-mount M12x0.35 M12x0.5 - S-mount M13x1 0.535"-40 - 13.59x0.635, Thorlabs SM05 M14x0.5 M16x0.5 - "M16" 0.8"-36 - 20x0.706, RMS microscope M25x0.75 - Nikon microscope 1"-32 - C-mount M26x0.706 - M26x36tpi, Miytoyo microscope 1.035"-40 - 26.29x0.635, Thorlabs SM1 M27x0.75 - Zeiss microscope M30.5x0.5 - Thorlabs SM30 M39x0.977 - M39x26tpi M42x0.75 - T-mount M42x1 2.035"-40 - 51.69x0.635, Thorlabs SM2 bayonet - Canon EF-mount bayonet - Leica M-mount bayonet - Nikon F-mount bayonet - Olympus OM-mount bayonet - Pentax K-mount bayonet - Sigma SA-mount bayonet - Leica M-mount bayonet - Nikon F-mount bayonet - Olympus OM-mount bayonet - Pentax K-mount bayonet - Sigma SA-mount https://www.thorlabs.com/newgrouppage9.cfm?objectgroup_id=1535 M75.5x0.5 - Thorlabs SM75, aperture 71.4mm 3.035"-40 - 77.09x0.635, Thorlabs SM3, aperture 71.4mm M100.5x0.5 - Thorlabs SM100, aperture 96.4mm 4.035"-40 - 102.49x0.635, Thorlabs SM4, aperture 96.8mm https://www.rafcamera.com/ M24x0.5 - lens mount, optical block of LOMO OKC1-22-1 lens M28.5x0.6 - lens mount, 1.25" astronomy filters M29x0.5 - lens mount, Arcturus binoviewer, Componon lenses, LWIR thermal cam lenses M30x0.5 - lens mount, optical block of LOMO OKC1-40-1 lens M30x0.75 - lens mount, some CCTV lenses M30.3x0.8 - lens mount, ENVIS (1.2"-32) astro M32x0.75 - lens mount M32.5x0.5 - lens mount, some objectives M33x0.75 - lens mount, LOMO Microplanar 4.5/65mm lenses M34x0.5 - lens mount, Agfa Repromaster 4.0/80mm, Agfa Repromaster 4.5/80mm, Staeble-magnogon R 5.6/105mm M34x0.7 - lens mount, some objectives M35x1 - lens mount, uncommon M38x0.8 - lens mount, Cooke Amotal lens M44x1 - lens mount, 35mm cameras, uncommon M45x0.75 - lens mount, 105mm Printing Nikkor M51x0.7 - optical filter M52x1 - lens mount, focusing helicoids M53x0.75 - optical filter M54x0.75 - lens mount, filter wheels, 2" Crayford-style astro focusers M54x1 - lens mount, focusing helicoids M58x1 - lens mount, focusing helicoids M65x1 - lens mount, Chinese focusing helicoids M68x1 - lens mount, Pentacon Six (P6) cameras M77.5-24 - lens mount, Aero Ektar lenses 3.3"-16 - lens mount, Celestron astro telescope (83.8x1.59) M90x1 - lens mount, astro telescope M117x1 - lens mount, astro telescope M36.4x1 - lens mount, Takahashi astro collimator? M22x0.5 - lens mount M28x0.5 - lens mount M35x0.75 - lens mount M64x1 M70x??? - lens mount, "M70" M76x0.75 - lens mount M88x??? M18x0.5 - lens mount, e.g. Schneider D-Claron 4/23mm https://rafcamera.com/adapters/for-lenses/step-rings?product_list_limit=all M67x1 M95x0.75 M96x0.75 M100x0.75 M105x0.75 M108.5x0.75 on Angenieux 10x25 T2 (25-250mm) zoom lens M112x1 M112x1.5 M115x0.75 known compatible lenses, front threads: m22.5x0.5 Lomography Minitar-1 32mm f/2.8 Art lens M23.5x0.5 Taylor-Hobson Cooke Kinic 25mm f/1.5 lens M29x0.5 Rodenstock 50mm f/2 Retina Heligon C Kodak Retina IIc, IIIc; Schneider&Kreuznach 50mm f/2 Retina-Xenon Kodak Retina IIa; Agfa 50mm f/2 Solagon KARAT IV M32x0.5 Watershot Underwater Housing for Samsung Galaxy S3, many of the older Kern Switar lenses M32x0.75 Watershot Underwater Housing for Apple iPhone M33x0.75 some Kiev-16U lenses (some have M35.5x0.5) M34x0.5 Angenieux 40mm Type S2, Angenieux 50mm Type S2 M34.5x0.5 lenses like old El-Nikkor 4/50mm M35x0.75 modern (not vintage version) Meyer Optik Görlitz Primoplan 58mm f/1.9 lens M35.5x0.75 Helios-44-3M lens, Kiev-16U lenses (some have M33x0.5) M38x0.5 Meopta C-mount primes, Bolex 26mm lens, and others M39x0.75 Leica "E39" M39.3x0.7 16mm Angenieux lenses: Type R41 1.3/15mm; Type S41 1.4/25mm; Type S42 1.4/25mm; Type M1 0.95/25mm; Type P3 2.5/75mm M40x0.75 Canon 8-C 2x M40.5x0.75 on Thorlabs M40.5x0.75 male on lens, uncommon M45x0.5 KMZ RO2-2M 2/75mm lens, KMZ RO3-3M 2/50mm lens, LOMO OKS1-75-1 in OCT-18 M45-36 Sankor, Singer, Eiki 16C, Eiki 16F, Kowa 16-D, Kowa 16-S, Sun Anamorphic, Angenieux 17-68mm, 17.5-70mm zoom lenses, ... M47x0.5 some Zeiss standard MK I prime lenses M49.5x0.75 Angenieux type S3 1.8/75mm, old Arriflex Schneider 10mm f1.8 lens M51x0.7 Angenieux Type M2 28mm lenses M52x0.75 LOMO Foton zoom lens M53x0.75 Nikon Repro-NIKKOR 1.0/85mm M56x0.7 Angenieux Type 6x12.5 12.5-75mm zoom lenses M58x0.75 Bolex 32/2x; Sankor, Singer, Eiki 16C, Eiki 16F, Kowa 16-D, Kowa 16-S, Sun Anamorphic; shutters: Compur #3, Copal #3, Prontor #3 M62x0.75 female on lens; LOMO OKS11-35-1 M62x0.75 male on lens; Omegaron 135 mm f/4.5, Rodagon 150 mm f/5.6, APO-Gerogon 210 mm f/9, APO-Gerogon 240 mm f/9 M65x0.75 Angenieux 9.5-57mm zoom lens M66.5x0.5 Angenieux Type M1 50mm lenses M68x1 Astro Zeiss extension M72x0.75 Kalimar 8/500mm lens, LOMO OKS10-28-1 M76x0.75 eg. LOMO Lenar zoom lens M77x0.75 Kiev-16U lenses M81x0.75 Philips SK 100mm F/1.5 projection lens M82x0.75 lenses with OCT-19 mount in Konvas housing that fit are: EKRAN 35OKS7-18-1, LOMO OKS5-18-1 M85x1 Salvo scanners, lenses with OCT-19 mount in Konvas housing that fit are: OKS7-28-1, OKS8-35-1, OKS1-50-1, OKS6-75-1 M86x0.75 some LOMO lenses with OCT-19 mount in Konvas housing - OKS1-50-6, OKS6-75-1 M95x0.75 Iscorama 54 lens M96x0.75 Angenieux Type 20x12 (3.5/12-240mm zoom lens), Angenieux 15-300mm zoom lens M100x0.75 LOMO 35BAS22-2, LOMO 35BAS23-2 M115x1 LOMO OKC1-18-1 smooth 97mm smooth 99mm LOMO OKC1-200-1 smooth 60mm smooth 62.5mm LOMO OKS5-18-1 in Konvas housing, LOMO OKS1-100-1 in Konvas housing smooth 37mm Kiev-16U lenses smooth 70.5mm projection lenses like Schneider Cinelux smooth 54mm Kowa 6mm lens smooth 83.5mm Leica-R 15mm lens smooth 58mm LOMO OKC8-35-1 in OCT-18 mount smooth 71mm smooth 80mm smooth 85mm smooth 70mm Kowa Prominar Anamorphic 16-H smooth 73mm LOMO OKS1-150-1 in Konvas housing smooth 62mm MC Zenitar-M 2.8/16mm attachments: M24x0.5 M: Bolex 8/19/1.5x attachment M27x0.5 M: Spiratone fish-eye 0.15x attachment M29.5x0.5 M: anamorphic attachments like KOWA Prominar 8/2x M30x0.5: Kowa 8, Baby Kowa 2x anamorphic adapter M34x0.5: anamorphic VM lens M34x1: Zeiss Ikon Steritar - a stereo attachment (beam splitter) allowing to take stereo picture pairs M37x0.75 M: Moondog Labs 1.33x anamorphic attachment, MSN-500 M40.5x0.5 M: Zeiss Ikon Steritar - a stereo attachment (beam splitter) allowing to take stereo picture pairs M54x1, 57.5mm smooth: Kowa 2x Anamorphic M55x0.75 F: Rapido FVD-8A attachment M67x0.75 M: Olympus underwater macro conversion lens (PTMC-01) and underwater wide conversion lens (PTWC-01) M67.7-36: front part of Schneider-Kreuznach Cinelux-Ultra 90mm F2 projection lens M68x0.75 M: FM Lens anamorphic attachment 39mm outer dia projection lenses that have 39 mm barrel diameter (like Kowa Prominar 16-A, for example) 43mm outer dia on rear: some projection lenses 49.5mm inner dia on rear: ISCO 2000 MC 52mm outer dia Kowa Prominar Anamorphic 16-H attachment, projection lenses 52.5mm outer dia projection attachment, ISCO Ultrastar Studio 80mm 54mm outer dia Kowa Anamorphic 35 1.5x 62.5mm outer dia: projection lenses 70mm outer dia 80mm inner dia 95mm outer dia matte box 95mm inner dia on rear: matte adapters 104mm outer dia relatively cheap LOMO projection anamorphic attachments of 35NAP series 114mm inner dia 120mm inner dia matte box M64x0.5, 52.5mm outer dia: projection lenses, ISCO-OPTIC CINEMASCOPE ULTRA STAR 80mm - 5.15 inch lens M75x0.7 F: single focus solution with 75mm female thread (HCDNA, FVD-16A) M75x0.75 F: Rapido FVD-16A attachment M45x0.75 rear mount thread on 105mm Printing Nikkor M49x0.75 M52x0.75 macro rings, circular lights M55x0.75 standard filter size M58x0.75 common standard filter size M62x0.75 circular lights M67x0.75 M77x0.75 common filters, circular light attachments M114x1 filters M26.5x0.5 lens mount, some Zeiss Microtar objectives M27x0.75 lens mount, microscope objectives, eg. Nikon CF Plan infinity/0 BD objectives, LOMO EPI-objectives M44x0.5 on some LOMO 75mm optical blocks M44x0.75 on some LOMO 75mm optical blocks, eg. LOMO lenses like OKS1-75-1, OKS6-75-1 adapter M72x0.75+M77x0.75+M86x1 to M77x0.75; 95mm outer dia to couple to matte box M18x0.75 some microscope turrets microscope dovetail diameters: 37mm 39.7mm 41mm 42mm 43mm 43.5mm 44mm 46mm 47mm 48.5mm 49.5mm 50.4mm 53.7mm 56mm Dovetail part is made with 39.7mm max diameter. This corresponds to phototube connection of American Optics / Reichert Diastar microscope Dovetail part is made with 50.4 mm max diameter. This corresponds to optical connection of American Optics / Reichert Diastar microscope. Nikon F mount Canon EOS mount
http://midopt.com/mounting-solutions/threaded-mount/ out.d aperture M13.25x0.5 14.4 10.6 M22x0.5 on Edmund Scientific 12mm Cx lens M22.5x0.5 24 18.5 1-32 25.2 19.5 C-mount M25.5x0.5 27.5 21 M27x0.5 29 22.5 M30.5x0.5 32.5 25.5 M34x0.5 36 29 M35.5x0.5 37.5 30.5 M37x0.75 39 31.9 M37.5x0.5 39.5 32.5 M39x0.5 41 34 M40.5x0.5 42.5 35.5 M43x0.75 45 38 M46x0.75 48 41 M48x0.75 50 43 M49x0.75 51 44 M52x0.75 54 47 M55x0.75 57 50 M58x0.75 60 52.9 M62x0.75 64 57.1 M67x0.75 70 61.8 M72x0.75 75 66.9 M77x0.75 80 71.9 M82x0.75 85 76.8 M86x1.0 89 80.8 M95x1.0 98.2 89.9 M105x1.0 109.8 100 https://www.dpreview.com/forums/thread/2713037 https://www.reddit.com/r/AskPhotography/comments/2zbemv/most_common_lens_filter_sizes/cphu2vs/ The full set of diameters used by Canon (I think) is: 52mm - only used on a few lenses, mostly primes, Canon Used on the small primes, such as the 50mm 1.8 mark 1 and the 28mm 2.8, and on some earlier consumer/midrange zoom lenses. 58mm - very common on consumer level lenses, vast majority of Canon midrange zooms, Canon few midsize zooms L and non-L 67mm - only used on a few lenses 72mm - most common on mid-range lenses (gold ring), Canon large/mid zooms and few primes 77mm - most common on high-end lenses (red ring), Canon most common on larger L-series lenses 82mm - only used on the TSE-24mm mkII(?), but I think some Sigma lenses use it as well https://www.dyxum.com/dforum/filter-threads-are-they-the-same_topic22871.html Hoya filters M24x0.5 M27x0.5 M27x0.75 M30x0.5 M30.5x0.5 M34x0.5 M37x0.75 M37.5x0.5 M39x0.5 M40.5x0.5 M43x0.75 M46x0.75 M49x0.75 50mm bayonet (older Hasselblad lenses) M52x0.75 M55x0.75 M58x0.75 60mm bayonet (current Hasselblad lenses) M62x0.75 M67x0.75 M72x0.75 M77x0.75 M82x0.75 M86x0.75 M95x0.75 B+W lists their 86,95,105,112 and 122mm filters as having Metric 1.0mm thread pitch. Below these all are .75mm pitch until you reach 43mm where both .05 and .75mm pitches are available. M86x1 M95x1 M105x1 M112x1 M122x1 https://tiffen.com/collections/filters/products/deep-yellow-15-screw-in-filter M94x M107 M127 M138 M110 M112.5 M125x1 M127x0.75 M138x1? M145x1 TV cameras: https://www.fujifilm.eu/fileadmin/countries/FR/optical_devices/Documentations/Catalogue_TV_et_Cinema_FUJINON_2017.pdf M127x0.75 M82x0.75 M95x1 M107x1
https://www.server-racks.com/rack-screws-10-32-12-24-m6.html and EIA-310-D (Figure 3) 10-32 UNF-2B - dia. 3/16" (4.76mm), original 19" rack size 12-24 UNC-2B - dia. between 4.8..5.5mm, now more common in prethreaded racks than 10-32 M5x0.8-6H - metric threads M6x1-6H - metric threads
see tables/shankwheel
http://www.tri-techmedical.com/sites/default/files/99-0550%20REV%20A%20-%20fairfield%20coupler%20outlets_0.pdf 1/2-20 UNF oxygen 5/8-28 UN oxygen 9/16-18 UNF left oxygen 5/8-18 UNF vacuum 9/16-18 UNF vacuum 9/16-28 UN vacuum 9/16-28 UN nitrous oxide 9/16-18 UNF nitrogen M14x1.25 air
https://www.stiweb.com/Mounting_Adapters_s/154.htm 10-32 1/4-28 common 1/4-20 5/16-24 3/8-24 1/2-20 M6x1 M6x1.25 M8x1.25 M10x1 M10x1.25
5-44 M5 10-32 M 1/4-32 M25
http://www.smcpneumatics.com/pdfs/smc/70FITTING.pdf M3 M5 G1/8 10-32 UNF 1/16 NPT 1/8 NPT M3 small pneumatic tubing ports (also M5, 10-32, 1/16 NPT, 1/8 NPT, G1/8) M5 small pneumatic tubing ports (also M3, 10-32, 1/16 NPT, 1/8 NPT, G1/8) 10-32 UNF small pneumatic tubing ports (also M3, M5, 1/16 NPT, 1/8 NPT, G1/8) 1/16 NPT small pneumatic tubing ports (also M3, M5, 10-32, 1/8 NPT, G1/8) 1/8 NPT small pneumatic tubing ports (also M3, M5, 10-32, 1/16 NPT, G1/8) G1/8 small pneumatic tubing ports (also M3, M5, 10-32, 1/16 NPT, 1/8 NPT)
usually male on tip M5 M6(x1) 1/4-28 1/4 UNC 5/16-24 UNF 5/16-18 UNC 3/8-28 (?) 3/8-24 - spot welder M8x1 M8x1 left (adaptor-diffuser for 1/4 UNF tip and M10x1.75 diffuser M8(x1.25) M9 M10 M10x1 M11x1 gas diffusers: 7/16 UNF 7/16-14 UNC on M10/M10x1 tip 9/16 UNF 5/8 UNF on M10 tip holder 7/8 UNF M16x1 on M10/M8 tip adapter M10x1 M10x1.75 M11x1.5 3/4 BSW 7/8 BSW 15/16 W 1" BSW M8 G1/4 M12x1 M11x1 M18.5 M21 M24 head assembly: 1/4 NPT 1/2 UNF 3/8 UNF (to 1/4 UNF tip, 1/2 UNC or 9/16 UNC shroud) M10x1/5 (to M6 tip, M11x1.5 shroud) 1/4 BSP (to M8 tip, 9/16 UNF or 5/8 UNF shroud) spot-weld tips: 3/8-16 7/16-14 atyp 3/4-10 5/8-18 5/8-11 3/4-10 Dremel M19x2 milling machine collet 3/4-16 Dremel handheld, throat mount thread (3/4-12?) M18x2 M2 3mm/3.2mm mandrel screw M1.7 for center hole 1.8mm or 1/16", 3/32" shanks M3 M6 for center hole 6mm 1/16 screw 1/8 screw 1/8-40 #5 UNC M3.175x0.635 common larger hole diameter 6.35mm or 1/4" arbor holes: 1/16 1.6mm 1/8 3.175mm 1/4 6.35mm M6 3/8 9.525mm Lathe spindles: http://www.lathe.com/spindles.html M12x1 Emco Maier Unimat SL M14x1.5 Cowells 90 3/4-16 Taig Microlathe II 1-10 Atlas 10100 1-8 Sears 101.0x 1.1/8-12 Myford, Seneca Falls Star 1.1/4-12 Dalton 1.3/8-10 South Bend Jr 1.1/2-8 Logan, Jet, Atlas TH42/5991/3986, Sears 101.2x M38x3 Habegger Neotor, Schaublin 102/102VM M39x4 King CH-920 AG, Emco Maier Maximat V10 1.432-12(?) Seneca Falls Star 9x5 1.3/4-8 Sheldon LWQ, Sheldon L44 2.1/4-8 South Bend, Logan, Sheldon WM-46-P, Sidney Machine Lot 160 2.1/4-6 South Bend 183-D 2.35-8 Jet 1236P 2.3/8-5 LeBlond 2.3/4-6 Monarch 2.656-8 Barker https://www.teknatool.com/thread/ M20x2 Tyme Cub M20x1.5 Electra Beckum, Multico Sumaro 1.1/8-8 UN 7/8-12 NS left 3/4-16 3/4-4 BSP left,right TL1000 (pre 1986) 1"-10 BSF TL1000, Woodfast/Durden 1"-10 BSF left TL1000, Woodfast/Durden 1"-8 UNC Delta, Rockwell, Golding, General, NOVA Comet (North America) and Mercury lathes 1-8 UNC l+r dual NOVA Mercury Mini Lathe 1"-12 UNF Myford ML8 Turnstyler 3/4-10 BSW Rockwell Homecraft M24x3 B-Line Arundel K600/K450 1.1/8-12 BSW Myford Mystro Masterlathe (New Zealand) 1.1/8-7 BSW Morton M18x2.5 Elu DB 180 1.1/4-8 NOVA Galaxi, NOVA Saturn, NOVA DVR 3000, NOVA XP, NOVA 1624 and 1624 II (North America), Laguna Revo M30x3.5 NOVA TL1500/3000/Comet (European and Southern Hemisphere), Woodfast 1.1/8-12 UNF Taiwanese lathes 7/8-14 NF M25x2 Tyme Avon (’83 on) and Classic Tanner SD165, Selbix Springwood, Sorby, Cotech
male 2mm: M2.5 4-40 male 4mm: M2 (female) M3 M4 M5 6-32 8-32 10-32 female 4mm: 1/4-32 (metal) M6 M8 (metal, plastic) M12x0.75 (plastic, highvoltage large)
https://image.isu.pub/091130212327-c061e2be7b014eb7ae534e629c7ec98c/jpg/page_180.jpg internal external 1/4-20 3/8-20 5/16-18 15/32-18 3/8-16 9/16-16 1/2-13 47/64-13 5/8-11 29/32-11 3/4-10 1.5/64-10 M6 3/8-20 M8 15/32-18 M10 9/16-16 M12 47/64-13 M16 29/32-11
internal external 4-40 10-32 6-32 1/4-20 8-32 5/16-18 10-32 5/16-18 10-32 3/8-16 10-32 M16x2 10-24 5/16-18 10-24 3/8-16 1/4-28 7/16-14 1/4-28 3/8-16 1/4-20 7/16-14 1/4-20 3/8-16 1/4-20 1/2-13 5/16-24 7/16-14 5/16-24 1/2-13 5/16-18 7/16-14 5/16-18 1/2-13 3/8-24 9/16-12 3/8-24 1/2-20 3/8-24 1/2-13 3/8-16 5/8-11 3/8-16 9/16-12 3/8-16 1/2-20 7/16-20 9/16-12 7/16-20 5/8-11 7/16-14 9/16-12 7/16-14 5/8-11 1/2-20 3/4-10 1/2-13 3/4-10 1/2-13 5/8-11 3/8-16 1/2-13 3/8-16 9/16-12 1/2-20 5/8-11 1/2-20 3/4-10 5/8-18 3/4-16 5/8-18 7/8-9 5/8-11 7/8-9 5/8-11 1-8 3/4-16 1-8 3/4-10 1-8 7/8-9 1.1/4-7 M3x0.5 M6x1 M4x0.7 M8x1.25 M5x0.8 M8x1.25 M6x1 M10x1.5 M6x1 3/8-16 M8x1.25 M12x1.75 M8x1.25 7/16-14 M8x1.25 1/2-13 M10x1.25 9/16-12 M10x1.25 M16x2 M10x1.5 9/16-12 M12x1.75 3/4-10 M12x1.75 M16x2 M16x2 1-8 M24x3 M36x4 wire inserts M16x1.5 M22x1.5 Plastite threadforming screws http://fasteners.oemfast.com/viewitems/all-categories/plastite-302-stainless-steel-thread-forming-screws 00-51 0-42 1-32 2-28 4-20 6-19 8-16 10-14 M1.59x0.60 M1.91x0.79 M2.26x0.91 M2.63x1.06 M3.12x1.27 M3.63x1.34 M4.55x1.59 Dril-Kwick self-drilling self-tapping Plasti-Fast http://fasteners.oemfast.com/viewitems/specialty-screws/dril-kwick-self-drilling-self-tapping-screws http://fasteners.oemfast.com/viewitems/specialty-screws/plasti-fast 4-24 Plasti-Fast only 6-20 8-18 10-16 12-14 1/4-14 Mag-Form thread-forming, for low-ductility eg. magnesium casting, wide-spaced thread with broad flank angle http://fasteners.oemfast.com/item/mag-form/thread-cutting-screws-for-magnesium-die-casting/8937 http://fasteners.oemfast.com/viewitems/mag-form/mag-form-thread-forming-screws MG1.4x0.60 MG1.6x0.70 MG2x0.80 MG2.5x0.90 MG3x1.00 MG3.5x1.20 MG4x1.40 MG5x1.60 MG6x2
https://www.elotechnik.cz/pripojka-manometru/ one side: G1/2, G1/4 other side: M12x1.5,M14x15,M16x1.5,M18x1.5,M20x1.5 pressure testpoints: M16x2 Test20, worldwide standard M16x1.5 used by Samsung 5/8-14 BSF HSP system, less common S12.65x1.5 Test12, used by Kawasaki, Schwing also 1/8 NPT 1/4 NPT 5/16 SAE 7/16 SAE 9/16 SAE M10x1 M14x1.5 M16x1.5 https://www.hydracheck.com/catalog/gauge-port-adaptors/jic-37o-female-swivel-x-jic-37o-male-gauge-ports/ ports on T inserts: 7/16 ORB 9/16 ORB less common 1/4 NPT 1/8 NPT G1/8
inner outer M12x1.75 M16x1.5 M10x1.5 M14x1.5 M8x1.25 M12x1.5 M6x1 M10x1.5 M5x0.8 M8x1 M4x0.7 M6.5x0.75 M3x0.5 M5x0.5 https://www.kerbkonus.de/proddb/pdf/en.ds.20.pdf external thread KKV standard M/MO=metric repair insert S=cutting slots, minimal inward spring action, screw-locking effect SB=cutting bores, difficult to thread materials, three cutting edges, thick wall SBD=cutting bores, thinwalled, same outer thread pitch as standard metric to allow use of threadcutting machines to drive the insert inner outer M/MO outer S outer SB outer SBD M2 4.5x0.5 M2.5 4.5x0.5 M3 M5 5x0.5 5x0.6 M3.5 6x0.75 6x0.8 5x0.6 M4 M6 6.5x0.75 6.5x0.8 6x0.7 M5 M7 8x1 8x1 6.5x0.8 M6 9x1 M6 M8 10x1.5 10x1.25 8x1 M8 M12 12x1.5 12x1.5 10x1.25 M10 M14 14x1.5 14x1.5 12x1.5 M12 M16 16x1.5 16x1.75 14x1.75 M14 18x1.5 18x2 M16 20x1.5 20x2 M18 22x1.5 22x2 M20 26x1.5 26x2 M22 26x1.5 26x2 M24 30x1.5 30x2 M27 34x1.5 M30 36x1.5 M4,M5,M6/10x1.5,M8,M10,M12 with hex drive inside M4,M5,M6/10x1.5,M8,M10 with head 4-48 UNF 5x0.5 4-40 UNC 5x0.5 6-40 UNF 6x0.75 6-32 UNC 6x0.75 8-36 UNF 6.5x0.75 8-32 UNC 6.5x0.75 10-32 UNF 8x1 10-24 UNC 8x1 1/4-28 UNF 10x1.5 1/4-20 UNC 10x1.5 1/4 BSW 10x1.5 5/16-24 UNF 12x1.5 5/16-18 UNC 12x1.5 5/16 BSW 12x1.5 3/8-24 UNF 14x1.5 3/8-16 UNC 14x1.5 3/8 BSW 14x1.5 7/16-20 UNF 16x1.5 7/16-14 UNC 16x1.5 7/16 BSW 16x1.5 1/2-20 UNF 18x1.5 1/2-13 UNC 18x1.5 1/2 BSW 18x1.5 5/8-18 UNF 20x1.5 5/8-11 UNC 20x1.5 5/8 BSW 20x1.5
from 6063 aluminium, blind rivets with thread common: 6-32 8-32 10-32
Most UK woodworking lathe headstock nuts: 3/4-16 UNF - spanner 1"1/8, UNified Fine, 28.6mm, dia 19.05mm 1-8 UNC - spanner 1"1/2, UNified Coarse, 38.1mm, dia 25.4mm M33x3.5 - spanner 50mm 1.5-6 M12x1 - smaller lathe chucks M20x2 - big drill/lathe chucks tapered cones: Jacobs taper: JT0, JT1, JT2, JT3, JT4, JT6, JT33 DIN B tapers: B10, B12, B16 (B18, B22, B24) (small end of Morse MT1, large MT1, small MT2, large MT2, small MT3, large MT3) chuck keys: common: 10mm (9.5mm, 3/8"), 13mm (12.7mm, 1/2"); less common: 16mm (15.875mm, 5/8"), 6mm (6.35mm, 1/4") 1/2": 10mm rod diameter, 6mm insert hole dia, 12.5mm (1/2") outer dia of the cogwheel 3/4": 13mm rod diameter, 6mm insert hole dia, 18mm (3/4") outer dia of the cogwheel quads of chuck keys: 1/4, 3/8, 1/2, 5/8 (2/8, 3/8, 4/8, 5/8) chuck tapers: JT0: 0.3..4 mm JT3: 3/16..3/4 B10: 0.6..6 B12: 1.5..10 B16: 1.5..13, 3..16, 5..20
M10x0.75 ERM8 mini collet nut M13x0.75 ERM11 mini collet nut M14x0.75 ER11 collet nut M19x1.0 ERM16 mini collet nut M22x1.5 ER16 collet nut M24x1.0 ERM20 mini collet nut M25x1.5 ER20 collet nut M30x1.0 ERM25 mini collet nut M32x1.5 ER25 collet nut M40x1.5 ER32 collet nut M50x1.5 ER40 collet nut M64x2 ER50 collet nut M33x1.5 OZ16 collet nut M42x2 OZ20 collet nut M48x2 OZ25 collet nut M60x2.5 OZ32 collet nut M68x2.5 OZ40 collet nut
M10x1 10 9.1 M12x1.25 12 10.5 M14x1.25 14 12.8 M18x1.5 18 16.8
https://www.hatraco.com/sites/default/files/downloads/auburn_productcatalog.pdf 1/2-14 NPT 3/4-20 NEF 13/16-24 7/8-18 NPT 7/8-14 NPT M10x1 SAE M14x1.25 SAE M18x1.5 SAE 11/16-24 NEF on top of M18x1.5 igniter 5/8-24 UNEF on top of M18x1.5 igniter
1/2-14 NPT 1/4-18 NPT M10x1 3/4-20 on top of 1/2 NPT flame rod
3/8-18 PTF SAE PTF=NPTF=NPT dry-seal 1/2-14 NPT 5/8-24 NEF 1-11.5 SAE
3/8-18 NPTF 1/2-14 NPT 5/8-24 NEF 7/8-14 UNF 1-11.5 NPT 1.5/8 NPT(?) 1.7/8-12 UN centerwires: 6-32 NC 10-24 NC 1/4-20 NC 3/8-16 NC 5/8-11 NC 7/8-14 UNF
1/2-14 NPT 3/4-14 NPT 1-11.5 NPT 7/8-18 NPT industrial igniters 7/8-14 NPT industrial igniters 1.5/8 NPT electrical feedthroughs
M18x1.5, spanner 22mm
M12x1.25 M12x1.5 (M14x1.25) M14x1.5 M16x1.5 M18x1.5 M20x1.5
0# 0.060-80 UNF d=1.524mm 1# 0.073-64 UNC d=1.854mm 1# 0.073-72 UNF d=1.854mm 2# 0.086-56 UNC d=2.184mm 2# 0.086-64 UNF d=2.184mm 3# 0.099-48 UNC d=2.515mm 3# 0.099-56 UNF d=2.515mm 4# 0.112-40 UNC d=2.845mm 4# 0.112-48 UNF d=2.845mm 5# 0.125-40 UNC d=3.175mm 5# 0.125-44 UNF d=3.175mm 6# 0.138-32 UNC d=3.505mm 6# 0.138-40 UNF d=3.505mm 8# 0.164-32 UNC d=4.166mm 8# 0.164-36 UNF d=4.166mm 10# 0.190-24 UNC d=4.826mm 10# 0.190-32 UNF d=4.826mm 12# 0.216-24 UNC d=5.486mm 12# 0.216-28 UNF d=5.486mm 12# 0.216-32 UNEF d=5.486mm 1/4-20 UNC d=6.350mm 1/4-28 UNF d=6.350mm 1/4-32 UNEF d=6.350mm 5/16-18 UNC d=7.938mm 5/16-24 UNF d=7.938mm 5/16-32 UNEF d=7.938mm 3/8-16 UNC d=9.525mm 3/8-24 UNF d=9.525mm 3/8-32 UNEF d=9.525mm 7/16-14 UNC d=11.11mm 7/16-20 UNF d=11.11mm 7/16-28 UNEF d=11.11mm 1/2-13 UNC d=12.70mm 1/2-20 UNF d=12.70mm 1/2-28 UNEF d=12.70mm 9/16-12 UNC d=14.29mm 9/16-18 UNF d=14.29mm 9/16-24 UNEF d=14.29mm 5/8-11 UNC d=15.88mm 5/8-18 UNF d=15.88mm 5/8-24 UNEF d=15.88mm 3/4-10 UNC d=19.05mm 3/4-16 UNF d=19.05mm 3/4-20 UNEF d=19.05mm 7/8-9 UNC d=22.23mm 7/8-14 UNF d=22.23mm 7/8-20 UNEF d=22.23mm 1-8 UNC d=25.40mm 1-12 UNF d=25.40mm, uncommon, 1-14 used instead 1-14 UNF d=25.40mm, de-facto standard for UNF 1-20 UNEF d=25.40mm
https://www.rntap.com/tap-technical-information/metric-tap-drill-sizes-percentages-threads.aspx M20x2.5 17.5 77% M20x1.5 18.5 77% M22x2.5 19.5 77% M22x1.5 20.5 77%
http://www.hoseandfittings.com/int-thread-id/
outer diameter=d size=(d-1/4") ex. 1" dia == 3/4" thread BSP thread angled 55deg NPT thread angled 60deg (like metric) BSPP - parallel thread BSPT - tapered thread
ISO 7/1?? tapered or straight Whitworth thread, 55-deg outer dia drill G1/16x28 7.72mm 6.6 "G" G1/8x28 9.73mm 8.8 11/32 G1/4x19 13.2mm 11.8 29/64 G3/8x19 16.6mm 15.25 19/32 G1/2x14 20.9mm 19.0 3/4 G5/8x14 22.9mm 21.0 53/64 G3/4x14 26.4mm 24.5 31/32 G1x11 33.2mm 30.75 1.7/64 G1-1/4x11 41.9mm 39.5 1.35/64 G1-1/2x11 47.8mm 45.5 1.25/32 G1-3/4x11 53.7mm 51.0 2" G2x11 59.6mm 57.0 2.1/4"
tapered Unified thread, 60-deg TPI outer dia female dia 1/16 NPT 27 7.84 6.22 1/8 NPT 27 10.18 8.54 1/4 NPT 18 13.54 11.07 3/8 NPT 18 16.98 14.49 1/2 NPT 14 21.14 17.90 3/4 NPT 14 26.49 23.21 1 NPT 11.5 33.25 29.15 1 1/4 NPT 11.5 41.91 37.87 1 1/2 NPT 11.5 47.97 43.49 2 1/4 NPT 11.5 60.00 55.95 1/16 1/8 1/4 3/8 1/2 3/4
(M8x1.0) (M10x1.0) M12x1.5 M14x1.5 M16x1.5 M18x1.5 M22x1.5 (M24x1.5) M26x1.5 (M27x2.0) M30x1.5 (M33x2.0) (M36x2.0) M38x1.5 (M42x2.0) M45x2.0 (M48x2.0) M52x1.5 (M60x2.0)
M8x1.0 M10x1.0 M12x1.0 M14x1.0 M16x1.0 M12,14,16,18,20,22,24,26x1.5 M30,36,42,45,52x2.0
M14,16,18,22,24,30,33,36,42x1.5
M30,36,45x1.5
M12x1.5 on outside of bulkhad push-in tube couplers, 4mm tube M14x1.5 on outside of bulkhad push-in tube couplers, 6mm tube M16x1.5 on outside of bulkhad push-in tube couplers, 8mm tube M20x2 on outside of bulkhad push-in tube couplers, 10mm tube M24x2 on outside of bulkhad push-in tube couplers, 12mm tube https://www.metalwork.cz/media/Download_Bro_Cat/RACCORDI_AUTOMATICI_EN_0619.pdf push-fit couplers M3 M5 M7 M12x1.5 1/4 3/8 1/2 outside of bulkhead couplers: M8x0.75 2mm M11x1 2.5mm M13x1 4.5mm, 2.5mm M14x1 4mm M15x1 6.5mm, 2.5mm, 4.5mm M17x1 8mm, 4.5mm, 6.5mm M20x1 10mm, 6mm, 8mm M24x1 12mm inserts, cartridge slots R26: M7x0.75 3..3.17mm dia M9.5x0.75 4mm dia M10.5x0.75 5mm dia M11.5x0.75 6mm dia M13.5x0.75 8mm dia M15.5x0.75 10mm dia M18x1 12mm dia
from http://docs-europe.electrocomponents.com/webdocs/1553/0900766b815535ec.pdf M5x0.5 spanner 7.0, tip-tip 8.0, th.1.2 M6x0.75 1/4-40 Thd (6.35mm) spanner 8.0mm, tip-tip 9.0, th.1.5 M7x0.75 M8x0.75 spanner 9.0mm 15/32-32 NS (11.9mm) spanner ~15 th. ~1.7 (14.0, tt 16.0, th.2.0) M10x0.75 M12x1 spanner 14.0mm, tip-tip 16.0, th.2.0 (14.3, tip-tip 16.0; 15.2dia) M16x1 spanner 19.0mm th. 2.5mm M19x1 spanner 22.0mm th. 3.4mm. M22x1 M25x1 spanner 30, tt 33,. on knobs, male M2.3x0.4 M3.5x0.6
M12x1.5 PG7 3.5..6(3..6.5?)mm cable spanner 15mm M16x1.5 PG9 4..8 19 M18x1.5 PG11 5..10 22 M20x1.5 PG13.5 6..12 24 // G1/2 M22x1.5 PG16 10..14 27 M24x1.5 PG18 12..16 27 M25x1.5 PG19 12..15 M27x1.5 PG21 13..18 33 // G3/4 M30x1.5 PG24 15..22 36 // G1 M36x1.5 PG29 18..25 38 // G5/4 M46x1.5 PG36 22..32 42 // G3/2 M54x1.5 PG42 30..38 53 M60x1.5 PG48 34..44 60 // G2 NPT NPT1/4"x18tpi NPT-14 3..6.5 NPT3/8"x18 NPT-38 2..6,4..8 spanner 19mm NPT1/2"x14 NPT-12 5..9,6..12 24 NPT3/4"x14 NPT-34 9..16,13..18 33 NPT1"x11.5 NPT-1 13..20,18..25 41 NPT1-1/4"x11.5 NPT-114 13..20,18..25 42/46
M12x1.25 M14,16,18,20,22,24,26,27,30,33,36,42,48x1.5 M27,42,60x2
M6x1.0 MAL 16mm M8x1.25 MAL 20mm M10x1.25 MAL 25,32mm M12x1.25 MAL 40mm M14x1.25 M16x1.5 MAL 16mm M18x1.5 M22x1.5 MAL 20,25mm M24x2.0 MAL 32mm M26x1.5 M27x2.0 M30x2.0 MAL 40mm
M1 (uncommon) M1.2x0.25 (less uncommon) M1.4x0.3 (most) M1.4x0.5 thread forming M1.6x0.4 thread forming M1.6 (less uncommon) M2..M3 (todo)
M12x1.25 M12x1.5 M12x1.75 M14x1.25 M14x1.5 M16x1.5
M10x1.25 M12x1.25 M12x1.5 M14x1.5 M14x2 M16x1.5 1/2 UNF 9/16 UNF
http://www.bajk.cz/data/clanek.asp?id_clanek=566 car tire (Schrader) - most likely .305-32 UNS (M7.7x.794)? ARI Standard 720-97? (minor diameter 6.9mm) valve caps to fit: .307-32 http://www.rmpis.com/default.aspx?page=item+detail&itemcode=NAT+.305-32+UNS+2B+SP+PNT+PLUG+TAP ; oddball taps/dies: http://www.e-taps.com/products.htm 9/16-20 - bicycle crank arm pedal thread, multipiece pedals (left, right thread pair) 1/2-20 - bicycle crank arm pedal thread, one-piece or BMX crank vintage bicycle and motorbike and car threads: 3/16"-26 BSCY/BSB CEI 1/4"-26 BSCY/BSB CEI 5/16-26 BSCY/BSB CEI 3/8-26 BSCY/BSB CEI 7/16-26 BSCY/BSB CEI 1/2-26 BSCY/BSB CEI (all threads same pitch? suspicious!) set: 3/16-32 BSF 1/4-26 BSF,BSC 5/16-22 BSF 3/8-20 BSF and 3/16-24 BSW 1/4-20 BSW 5/16-18 BSW 3/8-16 BSW and 5/16-26 BSC/CEI 3/8-26 BSC/CEI and 0 BA 1 BA 2 BA 4 BA and 1/8-28 BSP 1/4-19 BSP set fine: 3/16-32 BSF 1/4-26 BSF 5/16-22 BSF 3/8-20 BSF 7/16-18 BSF 1/2-16 BSF another set: 3/16-24 1/4-20 5/16-18 3/8-16 7/16-14 1/2-12 5/8-11 3/4-10
http://pipelinepackaging.com/resources/cap-neck-finishes/ T: 21.5 - ext.dia of thread E: 20.0 - ext.dia without thread I: 16.5 - int.dia H: 9.5 - top height 2 thread turns, thread pitch=4mm
https://www.festo.com/wiki/en/Threads_in_pneumatics http://www.physics.ncsu.edu/pearl/Tap_Drill_Chart.html http://www.lincolnmachine.com/tap_drill_chart.html http://www.shender4.com/metric_thread_chart.htm extended range: http://mdmetric.com/tech/M-thead%20600.htm thread outer drill 75%(steel 50% thread) M1x0.25 1 0.75 M1.2x0.25 1.2 0.95 M1.4x0.3 1.4 1.1 M1.6x0.35 1.6 1.25 M1.8x0.35 1.8 1.45 M2x0.4 2 1.6 M2.2x0.45 2.2 1.75 M2.5x0.45 2.5 2.05 M3x0.5 3 2.5 M3.5x0.6 3.5 2.9 M4x0.7 4 3.3 M5x0.8 5 4.2 M6x1 6 5.0 M8x1.25 8 7.0 M10x1.5 10 8.5 M12x1.75 12 10.2 M16x2 16 14.0 M18x1 (fine) 18 17.0
W1/4-20 6.35 5.1(5.6) W3/8-16 9.525 7.9(8.4)
G1/8 9.73 8.8 28 tpi G1/4 13.16 11.8 19 tpi G3/8 16.66 15.25 19 tpi G1/2 20.95 19.0 14 tpi G3/4 26.44 24.5 14 tpi G1 33.25 30.75 11 tpi
M10x1 10 9.1 M12x1.25 12 10.5 M14x1.25 14 12.8 M18x1.5 18 16.8
M16x1.5 25mm shaft M16x2 M20x1.5 30mm shaft M24x2 35mm shaft, 40mm shaft M30x2 45mm shaft M36x3 50mm shaft
https://shop.advanceautoparts.com/p/kastar-master-spindle-rethreader-die-set-kas2599/22981087-P 11/16-24 common on vehicle spindle/axle stubs, central wheel mount 3/4-16 common on vehicle spindle/axle stubs, central wheel mount 3/4-20 common on vehicle spindle/axle stubs, central wheel mount 13/16-20 common on vehicle spindle/axle stubs, central wheel mount 27/32-20 common on vehicle spindle/axle stubs, central wheel mount 7/8-14 common on vehicle spindle/axle stubs, central wheel mount 1-14 common on vehicle spindle/axle stubs, central wheel mount M16x1 common on vehicle spindle/axle stubs, central wheel mount M16x1.5 common on vehicle spindle/axle stubs, central wheel mount M18x1.5 common on vehicle spindle/axle stubs, central wheel mount M19x1.5 common on vehicle spindle/axle stubs, central wheel mount M20x1 common on vehicle spindle/axle stubs, central wheel mount M20x1.25 common on vehicle spindle/axle stubs, central wheel mount M20x1.5 common on vehicle spindle/axle stubs, central wheel mount M22x1 common on vehicle spindle/axle stubs, central wheel mount M22x1.5 common on vehicle spindle/axle stubs, central wheel mount M24x1.5 common on vehicle spindle/axle stubs, central wheel mount M24x2 common on vehicle spindle/axle stubs, central wheel mount M25x1.5 common on vehicle spindle/axle stubs, central wheel mount M27x2 common on vehicle spindle/axle stubs, central wheel mount
M26x2 common on piping, faucet/tap/shower attachment thread, female on wall, male on faucet/tap M22x2 1/2" 3/4" M28x1.5 M8x1 faucet water attachment pipe M10x1 faucet water attachment pipe, most common metric
M6 for electrical cable holders/clamps M8 for smaller pipe holders/clamps (to 63mm), most common for ventillation pipes; also M10 M10 for pipe holders/clamps; together with M8 most common for "sane" sizes M12 for heavy pipe holders/clamps M16 for heavy pipe holders/clamps
type 25, type B - http://www.clecofasteners.com/Cleco-Specs/threadselftappingtype25.gif 2.2x0.8 #2-32 2.9x1.06 #4-24 3.5x1.27 #6-20 3.9x1.3 metric 4.2x1.41 #8-18 4.8x1.59 #10-16 5.5x1.81 #12-14 6.3x1.81 1/4-14, #14-14 8x2.1 5/16-12 9.5x2.1 3/8-12 #2-32 self-tapping screws type B, type 25; 2.2x0.8; coarse, sharp #4-24 self-tapping screws type B, type 25; 2.9x1.1; coarse, sharp #6-20 self-tapping screws type B, type 25; 3.5x1.3; coarse, sharp #8-18 self-tapping screws type B, type 25; 4.2x1.4; coarse, sharp #10-16 self-tapping screws type B, type 25; 4.8x1.6; coarse, sharp #12-14 self-tapping screws type B, type 25; 5.5x1.8; coarse, sharp 1/4-14 self-tapping screws type B, type 25; 6.3x1.8, #14-14; coarse, sharp 5/16-12 self-tapping screws type B, type 25; 8x2.1; coarse, sharp 3/8-12 self-tapping screws type B, type 25; 9.5x2.1; coarse, sharp M2.2x0.8 self-tapping screws type B, type 25, metric variant of #2-32 M2.9x1 self-tapping screws type B, type 25, metric variant of #4-24 M3.5x1.3 self-tapping screws type B, type 25, metric variant of #6-20 M3.9x1.3 self-tapping screws type B, type 25, metric M4.2x1.4 self-tapping screws type B, type 25, metric variant of #8-18 M4.8x1.6 self-tapping screws type B, type 25, metric variant of #10-16 M5.5x1.8 self-tapping screws type B, type 25, metric variant of #12-14 M6.3x1.8 self-tapping screws type B, type 25, metric variant of 1/4-14 M8x2.1 self-tapping screws type B, type 25, metric variant of 5/16-12 M9.5x2.1 self-tapping screws type B, type 25, metric variant of 3/8-12 type 2 B0 shape - https://us.misumi-ec.com/vona2/detail/221000546998/ 2.6-28 #3-28? 3-24 #4-24 4-18 #8-18 2 models grooved B1 shape - https://us.misumi-ec.com/vona2/detail/221000547764/?CategorySpec=00000071004%3a%3ah 2.6-40 x0.635 2.3-32 x0.794 2.5-28 x0.907 2.6-28 3-24 x1.06 3.5-20 x1.27 4-18 x1.41 4.5-16 x1.59 5-16 6-14 x1.81 thread-rolling self-tapping stainless - https://www.raajsagarsteels.com/fasteners_nut_bolts_screws_washer_studs/fasteners/stainless-steel-self-tapping-screws-dimensions.gif type F, type 1, type 23 tapping - http://www.clecofasteners.com/Cleco-Specs/threadsandpoints.gif Taptite - rolling - http://www.clecofasteners.com/Cleco-Specs/threadselftappingtype25.gif 2-56 UNC 3-48 UNC 4-40 UNC 5-40 UNC 6-32 UNC 8-32 UNC 10-32 UNF 10-24 UNC 12-24 UNC 1/4-20 UNC 5/16-18 UNC 3/8-16 UNC 1/2-13 UNC type A #6-18 #8-15 #10-12 #12-11 1/4-10 5/16-9 3/8-9 type P482 2-28 4-20 6-19 8-16 10-14 12-14 1/4-10 type HL - for plastic, thread-forming 2-32 4-24 5-20 6-19 7-19 8-18 10-16 12-16 1/4-15 5/16-14 PLAST 48/2 - for plastic, thread-forming, 48deg thread, 2-start 2-28 4-20 6-19 8-16 10-14 1/4-10 6-18 self-tapping screws type A, obsolete 8-15 self-tapping screws type A, obsolete 10-12 self-tapping screws type A, obsolete 12-11 self-tapping screws type A, obsolete 1/4-10 self-tapping screws type A, obsolete 5/16-9 self-tapping screws type A, obsolete 3/8-9 self-tapping screws type A, obsolete type P482 2-28 self-tapping screws type P482, for plastic 4-20 self-tapping screws type P482, for plastic 6-19 self-tapping screws type P482, for plastic 8-16 self-tapping screws type P482, for plastic 10-14 self-tapping screws type P482, for plastic 12-14 self-tapping screws type P482, for plastic 1/4-10 self-tapping screws type P482, for plastic type HL 6-18 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 8-15 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 2-32 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 4-24 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 5-20 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 6-19 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 7-19 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 8-18 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 10-16 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 12-16 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 1/4-15 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 5/16-14 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads PLAST 48/2 - for plastic, thread-forming, 48deg thread, 2-start 2-28 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 4-20 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 6-19 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 8-16 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 10-14 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 1/4-10 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 2-32 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 2-28 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 4-24 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 4-20 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 5-20 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 6-19 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 6-19 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 7-19 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 8-18 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 8-16 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 10-16 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 10-14 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 12-16 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 1/4-15 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads 1/4-10 self-tapping screws type PLAST 48/2, for plastic; 48-deg, double-start, sharp thin threads, trilobular 5/16-14 self-tapping screws type HL, for plastic; double-lead, high and low, sharp thin threads
https://elginfasteners.com/resources/screw-point-types/ Type A - tapping - coarsest - for thin metals (0.015..0.05", 0.38..1.27 mm), sheetmetal, resined plywood, asbestos; 60-deg; sharp point; not recommended for new designs Type B - tapping - coarse - for thick metals (0.05..0.2", 1.27..5.1mm), sheetmetal, nonferrous castings, plastics, plywood; 60-deg; larger root dia, finer pitch Type AB - tapping - coarse - type A tip with type B thread Type TK - drilling - type B thread with drilling tip Type TA - UNC Type 1 - cutting - UNC/UNF - single flute, general use, UNC/UNF-compatible thread Type 17 - cutting - coarsest? - for wood, special long sharp point, coarse thread Type 23 - cutting - UNC/UNF - for metals, UNC/UNF compatible machine screw thread, good chip clearing and maximum thread cutting area Type 25 - cutting - coarse - similar to Type 23, with Type B thread Type F - cutting - UNC/UNF - machine screw thread, for heavy sheetmetal, aluminium, zinc, lead castings, cast iron, brass, plastic Type C - forming - UNC/UNF - coarse or fine machine screw thread, blunt tapered point, higher torque, heavy sheetmetal and die castings Type CA - forming - UNC/UNF - like Type C, with gimlet point; useful when holes in adjanced layers slightly misaligned Tri-Round - forming - UNC - mostly coarse machine screw threads, better forming than Type C, needs less torque Lo-Driv - forming - UNC - mostly coarse machine screw threads, tapered end, low end load, low torque PF - cutting - for plastic, 30-deg thin long threads, smallest minor diameter HL - forming - for plastic, double-lead with high and low, sharp thin threads PLAST 48/2 - - for plastic, 48-deg thin long threads, less stress on plastic than 60-deg thread, trilobular PLAST 60/1 - - for plastic, 60-deg threads
https://brafasco.com/media/wysiwyg/Charts_UNC-UNF-MetricISO.pdf https://www.pencomsf.com/wp-content/uploads/2018/02/screw_book.pdf lots of data, specs: http://www.techvitas.lv/images/saito_pav/prod_gam_pram/produktu_grupes/standartiniai_irenginiu_elementai/varztai/varztai_main/standartiniai_pdf/REYHER_technine_informacija.pdf
http://www.techvitas.lv/images/saito_pav/prod_gam_pram/produktu_grupes/standartiniai_irenginiu_elementai/varztai/varztai_main/standartiniai_pdf/REYHER_technine_informacija.pdf diameters: 3 3.5 4 4.5 5 6 8 wood screws: DIN 95/96/97: 2 2.5 3 3.5 4 4.5 5 5.5 6 7 8 DIN571: 5 6 7 8 10 12 16 20
M20x1.25 M25x1.25 M27x1.5 G3/4 (?) G1/2 M24x1 T2 thread on G1/2, G3/4 M22x1.25 T2 on M25x1.25, M20x1.25 M16x1 G1/2 tap head (valve) hot/cold water, bottom thread T1 (corresponding top thread T2 commonly M24x1) G3/4 tap head (valve) hot/cold water, bottom thread T1 (corresponding top thread T2 commonly M24x1) M20x1.25 tap head (valve) hot/cold water, bottom thread T1 (corresponding top thread T2 commonly M22x1.25) M22x1.25 tap head (valve) hot/cold water, top thread T2 (corresponding bottom thread T1 commonly M20x1.25, M25x1.25) M25x1.25 tap head (valve) hot/cold water, bottom thread T1 (corresponding top thread T2 commonly M22x1.25) M27x1.5 tap head (valve) hot/cold water, bottom thread T1 (corresponding top thread T2 commonly M16x1) M16x1 tap head (valve) hot/cold water, top thread T2 (corresponding bottom thread T1 commonly M27x1.5) G3/8 on shower hoses, uncommon (on boats?) G1/2 most common on shower hoses G3/4 less common on shower hoses M15x1 common on pull-out kitchen sink shower heads faucet backnuts: G1/2 backnut for kitchen/bathroom faucets, small G3/4 backnut for kitchen/bathroom faucets G1 backnut for kitchen/bathroom faucets M33x1.5 common backnut (bottom attachment) thread on kitchen/bathroom faucets M52x1.5 backnut (bottom attachment) thread on larger kitchen/bath faucets G1.1/4 backnut for kitchen/bathroom faucets, large G1.1/2 backnut for kitchen/bathroom faucets, large; for syphons G2 backnut for kitchen/bathroom for syphons tub drains: 1.3/8-16 common US bathtub drain thread 1.5/8-16 common US bathtub drain thread, "fine", 1.1/4 NPSM 1.7/8-11.5 common US bathtub drain thread, "coarse", 1.1/2 NPSM 2.1/8-16 common US bathtub drain thread, "Kohler style"
https://www.bosch-easycontrol.com/media/easycontrol-rrc2.0/funktionen/ean_smart_radiator_thermostats_adapters.pdf M20x1.5 heating radiator valve thread, outside for thermostatic heat attachment; Gampper M22x? heating radiator valve thread, outside for thermostatic heat attachment; Gampper M28x1 heating radiator valve thread, outside for thermostatic heat attachment; Vama M28x1.5 heating radiator valve thread, outside for thermostatic heat attachment; most common; also on some thermostatic valves M30x1 heating radiator valve thread, outside for thermostatic heat attachment; Oventrop M30x1.5 heating radiator valve thread, outside for thermostatic heat attachment; common; on thermostatic valves HERZ, Bosch M33x2 heating radiator valve thread, outside for thermostatic heat attachment; Rossweiner M38x1.5 heating radiator valve thread, outside for thermostatic heat attachment; Ondal, Meges
https://www.kamody.cz/soubory/relatedfile/Accessories_spare_parts_TRVs_CS_low.pdf G3/8 G1/2 G3/4 G1 G1.1/4 G1.1/2 G2 M22x1.5 seen on some metric heating radiator piping systems M26x1.5 seen on some metric heating radiator piping systems M34x1.5 seen on some metric heating radiator piping systems M40x2 seen on some metric heating radiator piping systems M50x2 seen on some metric heating radiator piping systems M55x2 seen on some metric heating radiator piping systems M70x2 seen on some metric heating radiator piping systems valve inserts, internal side M16x1 seen on some heating radiator piping systems, on internal side of valve insert
https://www.bleedscrews.co.uk/radiator-bleed-screws/ 5.8-26 RR001 type 1, 30deg tip, cast iron radiators 6.2-24 RR002 type 2, cast iron radiators 5.85-26 RR003 type 3, most common, on most steel radiators 4.7-28 RR004 type 4, 41deg tip, most Myson radiators 5.4-28 RR005 type 5, 30deg tip 4.9-28 RR006 type 6, 37deg tip 5.3-28 RR007 type 7, 32deg tip 5.8-26 RR008 type 8, 30deg tip 6.3-26 RR009 type 9, 30deg tip 5.825-24 RR010 type 10, 30deg tip 4.625-30 RR011 type 11, 30deg tip 4.72-30 RR012 type 12, 45deg tip, older Myson radiators M4(x0.7) RR013 type 13, 45deg tip 5.95-26 RR014 type 14, 45deg tip 7.00-20 RR015 type 15, 30deg tip 4.72-30 RR016 type 16, 45deg tip 4.91-30 RR017 type 17, 45deg tip 4.62-30 RR018 type 18, 45deg tip 7.00-20 RR019 type 19 M4(x0.7) RR013 type 13, 45deg tip 4.62-30 RR018 type 18, 45deg tip 4.625-30 RR011 type 11, 30deg tip 4.7-28 RR004 type 4, 41deg tip, most Myson radiators 4.72-30 RR012 type 12, 45deg tip, older Myson radiators 4.72-30 RR016 type 16, 45deg tip 4.9-28 RR006 type 6, 37deg tip 4.91-30 RR017 type 17, 45deg tip 5.3-28 RR007 type 7, 32deg tip 5.4-28 RR005 type 5, 30deg tip 5.8-26 RR008 type 8, 30deg tip 5.8-26 RR001 type 1, 30deg tip, cast iron radiators 5.85-26 RR003 type 3, most common, on most steel radiators 5.825-24 RR010 type 10, 30deg tip 5.95-26 RR014 type 14, 45deg tip 6.2-24 RR002 type 2, cast iron radiators 6.3-26 RR009 type 9, 30deg tip 7.00-20 RR015 type 15, 30deg tip 7.00-20 RR019 type 19
NPT 1/4 US standard, female on cartridge M15x1.5 "fine" thread, male on cartridge M15x2.5 "coarse" thread, male on cartridge M20x1.5 male on cartridge 7/8-14 "fine" 7/8-9 "coarse"
https://patents.google.com/patent/EP1923086A1/en trapezoid thread root dia 8.0+-0.1mm inner dia 6.7+-0.1mm pitch 2.5..2.8 mm front inclination > 30deg (towards syringe inside) back inclination 25..50deg (towards syringe tip) top width of thread 0.3..0.6 mm two starts cone: https://en.wikipedia.org/wiki/Luer_taper male: 3.50mm top, widening with 6% taper (1.72 deg to centerline) female: 3.967mm hole, narrowing with 6% taper (1.72 deg to centerline)
M26x2 mandated in EU on bottles of gas with oxygen above 22% (Nitrox), converters available to G5/8 M25x2 "DIN", common worldwide M18x1.5 argon tanks for drysuit inflation, tanks too small to take M25x2 or G5/8 G5/8 7/8-14 UNF 2A on DIN
M16x2.5 standard reinforced concrete rebar couplers M18x2.5 standard reinforced concrete rebar couplers M22x2.5 standard reinforced concrete rebar couplers M25x3 standard reinforced concrete rebar couplers M28x3 standard reinforced concrete rebar couplers M32x3 standard reinforced concrete rebar couplers M36x3 standard reinforced concrete rebar couplers M40x3 standard reinforced concrete rebar couplers
G1/4 common outlet on handset, female on handset G3/8 common inlet to handset, commonly female on handset M22x?? outlet on handset, male on handset
https://cartreatments.com/lug-nut-sizes-types/ socket sizes: including: 17mm, 19mm (or 3/4″), 21mm (or 13/16”), 22mm (or 7/8”), or 23mm M10x1.25 car wheel nuts M12x1.2 car wheel nuts; very rare M12x1.25 car wheel nuts, bolts; very common M12x1.5 car wheel nuts, bolts; most common M12x1.75 car wheel nuts, bolts M14x1.25 car wheel nuts, bolts M14x1.5 car wheel nuts, bolts; very common M14x2 car wheel nuts; common M16x1.5 car wheel nuts M22x1.5 car wheel nuts 3/8-24 UNF car wheel nuts; classic mini 7/16-20 UNF car wheel nuts; SAE/US standard; common 1/2-20 UNF car wheel nuts; SAE/US standard; very common 1/2-13 car wheel nuts 9/16-18 UNF car wheel nuts; SAE/US standard; common 5/8-18 car wheel nuts; common 5/8-11 car wheel nuts 11/16-16 car wheel nuts 3/4-16 car wheel nuts 3/4-10 car wheel nuts 13/16-21 car wheel nuts 1.1/8-16 car wheel nuts
E5.5 Edison screw, lightbulbs, Liliput (LES); Indicator lights, decorative lights E10 Edison screw, 9.3mm, 14tpi; lightbulbs, Miniature (MES), C6; Indicator lights, decorative lights E11 Edison screw, lightbulbs, Mini-Candelabra; 120V-halogen E12 Edison screw, 11.5mm, 10tpi; lightbulbs, Candelabra (CES), C7; Indicator lights, decorative lights; uncommon E14 Edison screw, 13.5mm, 9tpi; lightbulbs, some fuse holders, Small or Mignon (SES); 230 V candelabra/chandelier, night lamps, and some pendant lights; very common in UK, Europe E17 Edison screw, 9tpi; lightbulbs, Intermediate (IES), C9; 120 V appliance / Outdoor Christmas E26 Edison screw, 7tpi; lightbulbs, Medium (MES, ES); Standard 120 V lamps E27 Edison screw, 26mm, 7tpi; lightbulbs, some fuse holders, Medium (ES); Standard 230 V lamps; most common in UK (also bayonets there), Europe E33 Edison screw, 32mm; used primarily for ceramic fuse holders above 35A E39 Edison screw, 4tpi; lightbulbs, Mogul/Goliath (GES); 120 V 250+ W industrial E40 Edison screw, 4tpi; lightbulbs, Mogul/Goliath (GES); 230 V 250+ W industrial
shaft minichuck adapters: 2, 2.35, 3.17, 4.05, 5.05mm motor shaft dia: quadcopter common: 3.17mm (0.125", 1/8") tool shaft diameters: rigid flange couplers: 3,4,5,6,7,8,10,11,12mm 3,4,5,6mm: cylinder outer dia 10mm, total height 12mm, holes ring dia 16mm w/ 4x M3 7,8,10,11,12mm: cylinder outer dia 16mm, height 10mm, tot height 13mm, holes ring 24mm (7,8,10mm hole) or 26mm (11,12,14) w/ 4x M4 14mm: cylinder outer dia 18mm, height 10mm, tot height 13mm, holes ring 26mm w/ 4x M4 shaft couplers dia: 2, 2.3, 3, 3.17, 4, 5, 6, 6.35, (7), 8, (9), 10, (11), 12, 14, 15, 16mm 2-2,3-3,4-4,4-6,4-8,5-5,5-8,6-6,6-8,6.35-8 2-2,2-3,2-3.17,2-4,2.3-4,3-3,3-4,3-5,3.17-4,3.17-5,4-4,4-6,5-5,5-6,5-6.35,5-7,5-8,6-6,6-7,6.35-6.35,6.35-8,6.35-10,8-8,8-10 reprap couplers - flexible (spiral cut) Al: 5-5, 5-8
http://www.classichonda.se/forum/mek-renovering/198-jis-standard?start=30 on vintage Japanese bikes and electronics M3x0.6 changed to M3(x0.5) M4x0.75 changed to M4(x0.7) M5x0.9 changed to M5(x0.8) M12x1.5 changed to M12x1.25
http://www.dovavanik.cz/zavitniky---vrtaky-INCH.html?xmlid=484963 UNF/NF: 1/4" NF 28 5/16" NF24 3/8" NF24 7/16" NF20 1/2“ NF20 9/16“NF18 5/8“ NF18 3/4“ NF16 7/8“ NF14 1“ NF14 UNC/NC: 1/4" NC20 5/16" NC18 3/8" NC16 7/16" NC14 1/2“ NC13 9/16“NC12 5/8“ NC11 3/4“ NC10 7/8“ NC9 1“ NC8
M2x0,4mm; M3x0,5mm; M4x0,7mm; M5x0,8mm M6x0,75mm; M6x1,0mm M7x0,75mm; M7x1,0mm M8x0,75mm; M8x1,0mm; M8x1,25mm M9x0,75mm; M9x1,0mm; M9x1,25mm M10x0,75mm; M10x1,0mm; M10x1,25mm; M10x1,5mm M11x0,75mm; M11x1,0mm; M11x1,25mm; M11x1,5mm M12x0,75mm; M12x1,0mm; M12x1,25mm; M12x1,5mm; M12x1,75mm M14x1,0mm; M14x1,25mm; M14x1,5mm; M14x2,0mm M16x1,0mm; M16x1,5mm; M16x2,0mm M18x1,5mm same for PT110-1, AH20110 https://www.segu.cz/Souprava-pro-zavitovani-110-dilu-d4140.htm "D4140" M3x0,5; M3x0,6 M4x0,7; M4x0,75 M5x0,8; M5x0,9 M6x0,75; M6x1,0 M7x0,75; M7x1,0 M8x1,0; M8x1,25 M10x1,25; M10x1.5 M12x1,5; M12x1,75 1/8-27 NPT GEKO G38300 M2x0.4 t d M3x0.5 t d M4x0.7 t d M5x0.8 t d M6x0.75 t d M6x1.0 t d M7x0.75 t d M7x1.0 t d M8x0.75 t d M8x1.0 t d M8x1.25 t d M9x0.75 t d M9x1.0 t d M9x1.25 t d M10x0.75 t d M10x1.0 t d M10x1.25 t d M10x1.5 t d M11x0.75 t d M11x1.0 t d M11x1.25 t d M11x1.5 t d M12x0.75 t d M12x1.0 t d M12x1.25 t d M12x1.5 t d M12x1.75 t d M14x1.0 t d M14x1.25 t d M14x1.5 t d M14x2.0 t d M16x1.0 t d M16x1.5 t d M16x2.0 t d M18x1.5 t d
代做工资流水公司商丘工资流水账单费用大连工资流水账单打印上海房贷银行流水 图片舟山工资流水app截图报价苏州房贷收入证明费用常德工资流水单多少钱大庆背调银行流水费用贵阳公司银行流水办理深圳代开车贷工资流水黄冈代办流水账单杭州车贷银行流水 查询广州流水图片青岛背调银行流水模板绍兴企业贷流水多少钱柳州办银行对公流水襄阳银行流水单打印桂林离职证明代办孝感入职流水图片宜昌公司银行流水报价长沙查薪资流水青岛办理收入证明厦门工作收入证明样本贵阳办理流水镇江打对公账户流水德阳开背调流水宁波查工资流水单镇江入职工资流水报价珠海制作流水单柳州企业流水打印办理岳阳薪资流水香港通过《维护国家安全条例》两大学生合买彩票中奖一人不认账让美丽中国“从细节出发”19岁小伙救下5人后溺亡 多方发声卫健委通报少年有偿捐血浆16次猝死汪小菲曝离婚始末何赛飞追着代拍打雅江山火三名扑火人员牺牲系谣言男子被猫抓伤后确诊“猫抓病”周杰伦一审败诉网易中国拥有亿元资产的家庭达13.3万户315晚会后胖东来又人满为患了高校汽车撞人致3死16伤 司机系学生张家界的山上“长”满了韩国人?张立群任西安交通大学校长手机成瘾是影响睡眠质量重要因素网友洛杉矶偶遇贾玲“重生之我在北大当嫡校长”单亲妈妈陷入热恋 14岁儿子报警倪萍分享减重40斤方法杨倩无缘巴黎奥运考生莫言也上北大硕士复试名单了许家印被限制高消费奥巴马现身唐宁街 黑色着装引猜测专访95后高颜值猪保姆男孩8年未见母亲被告知被遗忘七年后宇文玥被薅头发捞上岸郑州一火锅店爆改成麻辣烫店西双版纳热带植物园回应蜉蝣大爆发沉迷短剧的人就像掉进了杀猪盘当地回应沈阳致3死车祸车主疑毒驾开除党籍5年后 原水城县长再被查凯特王妃现身!外出购物视频曝光初中生遭15人围殴自卫刺伤3人判无罪事业单位女子向同事水杯投不明物质男子被流浪猫绊倒 投喂者赔24万外国人感慨凌晨的中国很安全路边卖淀粉肠阿姨主动出示声明书胖东来员工每周单休无小长假王树国卸任西安交大校长 师生送别小米汽车超级工厂正式揭幕黑马情侣提车了妈妈回应孩子在校撞护栏坠楼校方回应护栏损坏小学生课间坠楼房客欠租失踪 房东直发愁专家建议不必谈骨泥色变老人退休金被冒领16年 金额超20万西藏招商引资投资者子女可当地高考特朗普无法缴纳4.54亿美元罚金浙江一高校内汽车冲撞行人 多人受伤