Welcome to Scribd!
LCD-S866 Unofficial User Manual 2019 (June 6) - Fan-Made Version
LCD-S866 Unofficial User Manual 2019 (June 6) - Fan-Made Version
LCD-S866 Unofficial User Manual 2019 (June 6) - Fan-Made Version
1
Operating voltage and connectors
1.Operating voltage: DC24V, 36V, 48V, 60V. Other voltages can be customized.
2.Connectors
Controller power
2 Blue(K) on/off control line
Transmit data to
5 Yellow(TX) controller
Features:
1. The LCD displays: Trip time, Current speed, Trip distance, Wattage, Average speed,
Total distance travelled, Current, Maximum speed reached, Battery voltage, Battery
monitor, PAS level, Error codes and Status indicators.
2. The followings settings are available: Backlight brightness, Metric and imperial units,
Voltage level, Sleep time, Number of power assist levels, Wheel diameter, Number of
motor magnets, Speed limit, Zero start, Drive mode, Boost sensitivity, Boost start
strength, Number of PAS magnets, Controller current limit, Controller undervoltage,
ODO reset, Walk assist, Cruise control, Speed ratio, 0 gear and Communication protocol
3. Communication protocol: UART
2
All display functions are shown for 1 second (display test) when turning on the display.
1. Display content
1.1 Battery indicator
When the battery is full, all 6 segments of the battery indicator are visible (black).
ODO: total distance travelled, DST: trip distance, VOL: battery voltage, TM: trip
duration, CUR: operating current, WATT: instantaneous power, error code (see error
code table). Depending on P02 parameter value setting, speed is displayed in km or mile.
AVG: average speed, MAX: maximum speed, CUR: current speed (mph or km/h).
The speed signal is taken from the Hall sensors and/or speed sensor in the hub motor and
sent to the display via the controller. The display will calculate the speed by wheel
diameter and Hall signal/speed sensor data. If a geared hub motor does not have a built-
in speed sensor (no white Hall sensor wire), the display will only show speed when the
motor is engaged. In that case an external Hall speed sensor can be installed to constantly
show the speed, even when coasting. Depending on P02 parameter value setting, speed
is displayed in km/h or mph.
3
1.5 Status display area
To turn the display on or off, press and hold the power button .
After the display is turned on you will see display mode 1. Short press the power button
to cycle through all three available display modes.
Short press the plus button to increase the power assistance/speed limit level, short
press the minus button to decrease the power assistance/speed limit level. Selecting
PAS level 0 allows you to temporarily disable PAS/throttle. Note: PAS level 0 is
available only when parameter value P19 is set to “0”.
2.4 Lights
Long press the plus button to turn on the lights, the light icon will be shown on
the display and the lights will turn on. Long press the plus button again to turn the
lights off.
Walk assist powers the bicycle up to a steady 6 km/h allowing you to walk alongside
the bicycle without needing to push. Long press the minus button to activate walk
assist, the walk assist icon will be shown on the display. Long press the minus
button again to deactivate. Note: This function will only work when parameter
value P17 is set to “0”.
4
2.6 Automatic cruise control
Cruise control will automatically be engaged when a steady throttle speed is maintained
for six seconds. When the cruise control is engaged, the cruise icon will be shown
on the display and the throttle does not need to be held in position anymore for the
bicycle to maintain the current speed. Note: This function will only work when
parameter value P17 is set to “1”.
Zero start allows the motor to start accelerating from a complete standstill when using
the throttle. Note: The value of parameter P09 needs to be set to “0” to enable zero
start.
When zero start is disabled the bicycle needs to be moving at a minimum speed of ??
km/h before the throttle can activate the motor. Note: The value of parameter P09
needs to be set to “1” to disable zero start.
3. Settings
Short press the plus button to increase the parameter value, short press the minus
button to decrease the value. After modifying the parameter value, short press the
power button to save the parameter value and go to the next parameter.
After parameters are modified, long press the plus and minus buttons
simultaneously to manually save the parameters and exit parameter setting mode.
Alternatively you can wait 8 seconds to automatically save the parameters and exit
parameter setting mode.
Long press the plus and minus buttons simultaneously to enter parameter setting
mode. Now long press and hold the power and plus buttons simultaneously to
enter password setting mode.
Use the plus and minus buttons to modify a digit. Short press the power
button to go to the next password digit. After the password is modified, long press
the power and plus buttons simultaneously to save the password and exit
password setting mode.
(Note: From now on you will need to enter the password when powering on the
display).
Long press the plus and minus buttons simultaneously again to manually save
parameters, exit parameter setting mode and go back to the normal user interface.
Alternatively you can wait 8 seconds to automatically save parameters and exit
parameter setting mode.
5
(!) Forgot password
If you forget your password, use the override password: “3745”and press and hold the
?? button for 10 seconds to enter the normal user interface. You can now set a new
password by going through the steps described above.
4. Parameter list
Note: The P09-P15 menu is only valid when the display has an active data connection
with the controller.
5. Error Codes
An error code will be shown on the display if there is an error in the electrical function
of the bicycle. Error codes are automatically cleared when the problem has been corrected
and the bicycle has reached a minimum motor(assisted) speed of 6 km/h. See the table
below for error code descriptions.
E01 Reserved
E02 Brake
E08 Throttle
E09 Controller
E13 Headlight
玻璃钢生产厂家玻璃钢花盆多少钱一台东城区商场美陈公司报价艺术玻璃钢雕塑厂家常州商场美陈策划自贡市不锈钢玻璃钢雕塑厂家凭祥玻璃钢工艺品雕塑福建室内商场美陈价钱名图玻璃钢雕塑厂家玻璃钢雕塑厂湖南栖霞商场入口美陈榆林玻璃钢雕塑制作厂家新野玻璃钢雕塑定制福建玻璃钢卡通雕塑制作鸡西人物玻璃钢雕塑福建玻璃钢雕塑厂打聘淮安玻璃钢雕塑价格商场中秋主题活动美陈玻璃钢蘑菇雕塑定制苏州玻璃钢雕塑厂商嘉兴景观玻璃钢雕塑优势江苏公园玻璃钢雕塑公司玻璃钢剪纸雕塑怎样制作方法常见商场美陈制造楚雄玻璃钢门头雕塑宣城玻璃钢关公雕塑巢湖玻璃钢卡通雕塑金牛玻璃钢花盆花器范县玻璃钢雕塑价格兰考玻璃钢雕塑费用抚州玻璃钢雕塑多少钱香港通过《维护国家安全条例》两大学生合买彩票中奖一人不认账让美丽中国“从细节出发”19岁小伙救下5人后溺亡 多方发声单亲妈妈陷入热恋 14岁儿子报警汪小菲曝离婚始末遭遇山火的松茸之乡雅江山火三名扑火人员牺牲系谣言何赛飞追着代拍打萧美琴窜访捷克 外交部回应卫健委通报少年有偿捐血浆16次猝死手机成瘾是影响睡眠质量重要因素高校汽车撞人致3死16伤 司机系学生315晚会后胖东来又人满为患了小米汽车超级工厂正式揭幕中国拥有亿元资产的家庭达13.3万户周杰伦一审败诉网易男孩8年未见母亲被告知被遗忘许家印被限制高消费饲养员用铁锨驱打大熊猫被辞退男子被猫抓伤后确诊“猫抓病”特朗普无法缴纳4.54亿美元罚金倪萍分享减重40斤方法联合利华开始重组张家界的山上“长”满了韩国人?张立群任西安交通大学校长杨倩无缘巴黎奥运“重生之我在北大当嫡校长”黑马情侣提车了专访95后高颜值猪保姆考生莫言也上北大硕士复试名单了网友洛杉矶偶遇贾玲专家建议不必谈骨泥色变沉迷短剧的人就像掉进了杀猪盘奥巴马现身唐宁街 黑色着装引猜测七年后宇文玥被薅头发捞上岸事业单位女子向同事水杯投不明物质凯特王妃现身!外出购物视频曝光河南驻马店通报西平中学跳楼事件王树国卸任西安交大校长 师生送别恒大被罚41.75亿到底怎么缴男子被流浪猫绊倒 投喂者赔24万房客欠租失踪 房东直发愁西双版纳热带植物园回应蜉蝣大爆发钱人豪晒法院裁定实锤抄袭外国人感慨凌晨的中国很安全胖东来员工每周单休无小长假白宫:哈马斯三号人物被杀测试车高速逃费 小米:已补缴老人退休金被冒领16年 金额超20万